git.sur5r.net Git - u-boot/blob - include/configs/advantech_dms-ba16.h

   1 /*
   2  * Copyright (C) 2016 Timesys Corporation
   3  * Copyright (C) 2016 Advantech Corporation
   4  * Copyright (C) 2012 Freescale Semiconductor, Inc.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __ADVANTECH_DMSBA16_CONFIG_H
  10 #define __ADVANTECH_DMSBA16_CONFIG_H
  11
  12 #include <asm/arch/imx-regs.h>
  13 #include <asm/imx-common/gpio.h>
  14
  15 #define CONFIG_BOARD_NAME       "Advantech DMS-BA16"
  16
  17 #define CONFIG_MXC_UART_BASE    UART4_BASE
  18 #define CONSOLE_DEV     "ttymxc3"
  19 #define CONFIG_EXTRA_BOOTARGS   "panic=10"
  20
  21 #define CONFIG_BOOT_DIR ""
  22 #define CONFIG_LOADCMD "fatload"
  23 #define CONFIG_RFSPART "2"
  24
  25 #define CONFIG_SUPPORT_EMMC_BOOT
  26
  27 #include "mx6_common.h"
  28 #include <linux/sizes.h>
  29
  30 #define CONFIG_CMDLINE_TAG
  31 #define CONFIG_SETUP_MEMORY_TAGS
  32 #define CONFIG_INITRD_TAG
  33 #define CONFIG_REVISION_TAG
  34 #define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  35
  36 #define CONFIG_MXC_GPIO
  37 #define CONFIG_MXC_UART
  38
  39 #define CONFIG_MXC_OCOTP
  40
  41 /* SATA Configs */
  42 #define CONFIG_CMD_SATA
  43 #define CONFIG_DWC_AHSATA
  44 #define CONFIG_SYS_SATA_MAX_DEVICE      1
  45 #define CONFIG_DWC_AHSATA_PORT_ID       0
  46 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  47 #define CONFIG_LBA48
  48 #define CONFIG_LIBATA
  49
  50 /* MMC Configs */
  51 #define CONFIG_FSL_ESDHC
  52 #define CONFIG_FSL_USDHC
  53 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  54 #define CONFIG_BOUNCE_BUFFER
  55
  56 /* USB Configs */
  57 #define CONFIG_USB_STORAGE
  58 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  59 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  60 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  61 #define CONFIG_MXC_USB_FLAGS    0
  62 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
  63
  64 #define CONFIG_USBD_HS
  65 #define CONFIG_USB_FUNCTION_MASS_STORAGE
  66 #define CONFIG_USB_GADGET_VBUS_DRAW 2
  67
  68 /* Networking Configs */
  69 #define CONFIG_FEC_MXC
  70 #define CONFIG_MII
  71 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  72 #define CONFIG_FEC_XCV_TYPE             RGMII
  73 #define CONFIG_ETHPRIME         "FEC"
  74 #define CONFIG_FEC_MXC_PHYADDR          4
  75 #define CONFIG_PHYLIB
  76 #define CONFIG_PHY_ATHEROS
  77
  78 /* Serial Flash */
  79 #ifdef CONFIG_CMD_SF
  80 #define CONFIG_MXC_SPI
  81 #define CONFIG_SF_DEFAULT_BUS           0
  82 #define CONFIG_SF_DEFAULT_CS            0
  83 #define CONFIG_SF_DEFAULT_SPEED 20000000
  84 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
  85 #endif
  86
  87 /* allow to overwrite serial and ethaddr */
  88 #define CONFIG_ENV_OVERWRITE
  89 #define CONFIG_CONS_INDEX       1
  90
  91 #define CONFIG_LOADADDR 0x12000000
  92 #define CONFIG_SYS_TEXT_BASE    0x17800000
  93
  94 #define CONFIG_EXTRA_ENV_SETTINGS \
  95         "script=boot.scr\0" \
  96         "image=" CONFIG_BOOT_DIR "/uImage\0" \
  97         "uboot=u-boot.imx\0" \
  98         "fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \
  99         "fdt_addr=0x18000000\0" \
 100         "boot_fdt=yes\0" \
 101         "ip_dyn=yes\0" \
 102         "console=" CONSOLE_DEV "\0" \
 103         "fdt_high=0xffffffff\0"   \
 104         "initrd_high=0xffffffff\0" \
 105         "sddev=0\0" \
 106         "emmcdev=1\0" \
 107         "partnum=1\0" \
 108         "loadcmd=" CONFIG_LOADCMD "\0" \
 109         "rfspart=" CONFIG_RFSPART "\0" \
 110         "update_sd_firmware=" \
 111                 "if test ${ip_dyn} = yes; then " \
 112                         "setenv get_cmd dhcp; " \
 113                 "else " \
 114                         "setenv get_cmd tftp; " \
 115                 "fi; " \
 116                 "if mmc dev ${mmcdev}; then "   \
 117                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 118                                 "setexpr fw_sz ${filesize} / 0x200; " \
 119                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 120                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 121                         "fi; "  \
 122                 "fi\0" \
 123         "update_sf_uboot=" \
 124                 "if tftp $loadaddr $uboot; then " \
 125                         "sf probe; " \
 126                         "sf erase 0 0xC0000; " \
 127                         "sf write $loadaddr 0x400 $filesize; " \
 128                         "echo 'U-Boot upgraded. Please reset'; " \
 129                 "fi\0" \
 130         "setargs=setenv bootargs console=${console},${baudrate} " \
 131                 "root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \
 132         "loadbootscript=" \
 133                 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
 134         "bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
 135                 " source\0" \
 136         "loadimage=" \
 137                 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
 138         "loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
 139         "tryboot=" \
 140                 "if run loadbootscript; then " \
 141                         "run bootscript; " \
 142                 "else " \
 143                         "if run loadimage; then " \
 144                                 "run doboot; " \
 145                         "fi; " \
 146                 "fi;\0" \
 147         "doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
 148                 "run setargs; " \
 149                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 150                         "if run loadfdt; then " \
 151                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 152                         "else " \
 153                                 "if test ${boot_fdt} = try; then " \
 154                                         "bootm; " \
 155                                 "else " \
 156                                         "echo WARN: Cannot load the DT; " \
 157                                 "fi; " \
 158                         "fi; " \
 159                 "else " \
 160                         "bootm; " \
 161                 "fi;\0" \
 162         "netargs=setenv bootargs console=${console},${baudrate} " \
 163                 "root=/dev/nfs " \
 164                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 165         "netboot=echo Booting from net ...; " \
 166                 "run netargs; " \
 167                 "if test ${ip_dyn} = yes; then " \
 168                         "setenv get_cmd dhcp; " \
 169                 "else " \
 170                         "setenv get_cmd tftp; " \
 171                 "fi; " \
 172                 "${get_cmd} ${image}; " \
 173                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 174                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 175                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 176                         "else " \
 177                                 "if test ${boot_fdt} = try; then " \
 178                                         "bootm; " \
 179                                 "else " \
 180                                         "echo WARN: Cannot load the DT; " \
 181                                 "fi; " \
 182                         "fi; " \
 183                 "else " \
 184                         "bootm; " \
 185                 "fi;\0" \
 186
 187 #define CONFIG_BOOTCOMMAND \
 188         "usb start; " \
 189         "setenv dev usb; " \
 190         "setenv devnum 0; " \
 191         "setenv rootdev sda${rfspart}; " \
 192         "run tryboot; " \
 193         \
 194         "setenv dev mmc; " \
 195         "setenv rootdev mmcblk0p${rfspart}; " \
 196         \
 197         "setenv devnum ${sddev}; " \
 198         "if mmc dev ${devnum}; then " \
 199                 "run tryboot; " \
 200         "fi; " \
 201         \
 202         "setenv devnum ${emmcdev}; " \
 203         "setenv rootdev mmcblk${emmcdev}p${rfspart}; " \
 204         "if mmc dev ${devnum}; then " \
 205                 "run tryboot; " \
 206         "fi; " \
 207         \
 208         "bmode usb; " \
 209
 210 #define CONFIG_ARP_TIMEOUT     200UL
 211
 212 /* Miscellaneous configurable options */
 213 #define CONFIG_SYS_LONGHELP
 214 #define CONFIG_AUTO_COMPLETE
 215
 216 /* Print Buffer Size */
 217 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 218 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 219
 220 #define CONFIG_SYS_MEMTEST_START       0x10000000
 221 #define CONFIG_SYS_MEMTEST_END         0x10010000
 222 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 223
 224 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 225
 226 #define CONFIG_CMDLINE_EDITING
 227
 228 /* Physical Memory Map */
 229 #define CONFIG_NR_DRAM_BANKS           1
 230 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 231
 232 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 233 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 234 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 235
 236 #define CONFIG_SYS_INIT_SP_OFFSET \
 237         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 238 #define CONFIG_SYS_INIT_SP_ADDR \
 239         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 240
 241 /* FLASH and environment organization */
 242
 243 #define CONFIG_ENV_IS_IN_SPI_FLASH
 244 #define CONFIG_ENV_SIZE                 (8 * 1024)
 245 #define CONFIG_ENV_OFFSET               (768 * 1024)
 246 #define CONFIG_ENV_SECT_SIZE            (64 * 1024)
 247 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 248 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 249 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 250 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 251
 252 #ifndef CONFIG_SYS_DCACHE_OFF
 253 #endif
 254
 255 #define CONFIG_SYS_FSL_USDHC_NUM        3
 256
 257 /* Framebuffer */
 258 #ifdef CONFIG_VIDEO
 259 #define CONFIG_VIDEO_IPUV3
 260 #define CONFIG_VIDEO_BMP_RLE8
 261 #define CONFIG_SPLASH_SCREEN
 262 #define CONFIG_SPLASH_SCREEN_ALIGN
 263 #define CONFIG_BMP_16BPP
 264 #define CONFIG_VIDEO_LOGO
 265 #define CONFIG_VIDEO_BMP_LOGO
 266 #define CONFIG_IPUV3_CLK                260000000
 267 #define CONFIG_IMX_HDMI
 268 #define CONFIG_IMX_VIDEO_SKIP
 269 #endif
 270
 271 #define CONFIG_PWM_IMX
 272 #define CONFIG_IMX6_PWM_PER_CLK         66000000
 273
 274 #undef CONFIG_CMD_PCI
 275 #ifdef CONFIG_CMD_PCI
 276 #define CONFIG_PCI_SCAN_SHOW
 277 #define CONFIG_PCIE_IMX
 278 #define CONFIG_PCIE_IMX_PERST_GPIO      IMX_GPIO_NR(7, 12)
 279 #define CONFIG_PCIE_IMX_POWER_GPIO      IMX_GPIO_NR(1, 5)
 280 #endif
 281
 282 /* I2C Configs */
 283 #define CONFIG_SYS_I2C
 284 #define CONFIG_SYS_I2C_MXC
 285 #define CONFIG_SYS_I2C_SPEED            100000
 286 #define CONFIG_SYS_I2C_MXC_I2C1
 287 #define CONFIG_SYS_I2C_MXC_I2C2
 288 #define CONFIG_SYS_I2C_MXC_I2C3
 289
 290 #endif  /* __ADVANTECH_DMSBA16_CONFIG_H */