2 * am3517_evm.h - Default configuration for AM3517 EVM board.
4 * Author: Vaibhav Hiremath <hvaibhav@ti.com>
6 * Based on omap3_evm_config.h
8 * Copyright (C) 2010 Texas Instruments Incorporated
10 * SPDX-License-Identifier: GPL-2.0+
16 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
19 * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
20 * 64 bytes before this address should be set aside for u-boot.img's
21 * header. That is 0x800FFFC0--0x80100000 should not be used for any
25 #define CONFIG_SYS_TEXT_BASE 0x80100000
26 #define CONFIG_SYS_SPL_MALLOC_START 0x80208000
27 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
29 #include <configs/ti_omap3_common.h>
30 #undef CONFIG_SDRC /* Disable SDRC since we have EMIF4 */
32 #define CONFIG_MISC_INIT_R
33 #define CONFIG_REVISION_TAG
35 /* Hardware drivers */
37 /* allow to overwrite serial and ethaddr */
38 #define CONFIG_ENV_OVERWRITE
42 * Enable CONFIG_USB_MUSB_HOST for Host functionalities MSC, keyboard
43 * Enable CONFIG_USB_MUSB_GADGET for Device functionalities.
46 #ifdef CONFIG_USB_MUSB_AM35X
48 #ifdef CONFIG_USB_MUSB_HOST
50 #ifdef CONFIG_USB_KEYBOARD
51 #define CONFIG_PREBOOT "usb start"
52 #endif /* CONFIG_USB_KEYBOARD */
54 #endif /* CONFIG_USB_MUSB_HOST */
56 #endif /* CONFIG_USB_MUSB_AM35X */
61 #define CONFIG_DRIVER_TI_EMAC
62 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
64 #define CONFIG_BOOTP_DEFAULT
65 #define CONFIG_BOOTP_DNS
66 #define CONFIG_BOOTP_DNS2
67 #define CONFIG_BOOTP_SEND_HOSTNAME
68 #define CONFIG_NET_RETRY_COUNT 10
70 /* Board NAND Info. */
72 #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
74 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
75 #define CONFIG_SYS_NAND_PAGE_COUNT 64
76 #define CONFIG_SYS_NAND_PAGE_SIZE 2048
77 #define CONFIG_SYS_NAND_OOBSIZE 64
78 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
79 #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
80 #define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, 10, \
81 11, 12, 13, 14, 16, 17, 18, 19, 20, \
82 21, 22, 23, 24, 25, 26, 27, 28, 30, \
83 31, 32, 33, 34, 35, 36, 37, 38, 39, \
84 40, 41, 42, 44, 45, 46, 47, 48, 49, \
85 50, 51, 52, 53, 54, 55, 56 }
87 #define CONFIG_SYS_NAND_ECCSIZE 512
88 #define CONFIG_SYS_NAND_ECCBYTES 13
89 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
90 #define CONFIG_SYS_NAND_MAX_OOBFREE 2
91 #define CONFIG_SYS_NAND_MAX_ECCPOS 56
92 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
93 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
94 #define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
95 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
96 /* NAND block size is 128 KiB. Synchronize these values with
97 * corresponding Device Tree entries in Linux:
98 * MLO(SPL) 4 * NAND_BLOCK_SIZE = 512 KiB @ 0x000000
99 * U-Boot 15 * NAND_BLOCK_SIZE = 1920 KiB @ 0x080000
100 * U-Boot environment 2 * NAND_BLOCK_SIZE = 256 KiB @ 0x260000
101 * Kernel 64 * NAND_BLOCK_SIZE = 8 MiB @ 0x2A0000
102 * DTB 4 * NAND_BLOCK_SIZE = 512 KiB @ 0xAA0000
103 * RootFS Remaining Flash Space @ 0xB20000
105 #endif /* CONFIG_NAND */
107 /* Environment information */
109 #define CONFIG_BOOTFILE "uImage"
111 #define CONFIG_EXTRA_ENV_SETTINGS \
112 "loadaddr=0x82000000\0" \
113 "console=ttyO2,115200n8\0" \
114 "fdtfile=am3517-evm.dtb\0" \
115 "fdtaddr=0x82C00000\0" \
117 "bootenv=uEnv.txt\0" \
120 "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
121 "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
124 "mmcroot=/dev/mmcblk0p2 rw\0" \
125 "mmcrootfstype=ext4 rootwait fixrtc\0" \
126 "mmcargs=setenv bootargs console=${console} " \
130 "rootfstype=${mmcrootfstype} " \
132 "nandargs=setenv bootargs console=${console} " \
135 "root=ubi0:rootfs rw ubi.mtd=rootfs " \
136 "rootfstype=ubifs rootwait " \
138 "loadbootenv=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootenv}\0"\
139 "importbootenv=echo Importing environment from mmc ...; " \
140 "env import -t ${loadaddr} ${filesize}\0" \
141 "bootscript=echo Running bootscript from mmc ...; " \
142 "source ${loadaddr}\0" \
143 "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootfile}\0" \
144 "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdtaddr} ${fdtfile}\0" \
145 "mmcboot=echo Booting from mmc ...; " \
147 "bootz ${loadaddr} - ${fdtaddr}\0" \
148 "nandboot=echo Booting from nand ...; " \
150 "nand read ${loadaddr} 2a0000 800000; " \
151 "nand read ${fdtaddr} aa0000 80000; " \
152 "bootm ${loadaddr} - ${fdtaddr}\0" \
154 #define CONFIG_BOOTCOMMAND \
155 "mmc dev ${mmcdev}; if mmc rescan; then " \
156 "echo SD/MMC found on device $mmcdev; " \
157 "if run loadbootenv; then " \
158 "run importbootenv; " \
160 "echo Checking if uenvcmd is set ...; " \
161 "if test -n $uenvcmd; then " \
162 "echo Running uenvcmd ...; " \
165 "echo Running default loadimage ...; " \
166 "setenv bootfile zImage; " \
167 "if run loadimage; then " \
171 "else run nandboot; fi"
173 /* Miscellaneous configurable options */
174 #define CONFIG_AUTO_COMPLETE
175 #define CONFIG_CMDLINE_EDITING
176 #define CONFIG_SYS_LONGHELP
178 /* We set the max number of command args high to avoid HUSH bugs. */
179 #define CONFIG_SYS_MAXARGS 64
181 /* Print Buffer Size */
182 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
183 + sizeof(CONFIG_SYS_PROMPT) + 16)
184 /* Boot Argument Buffer Size */
185 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
187 /* memtest works on */
188 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
189 #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
190 0x01F00000) /* 31MB */
192 /* Physical Memory Map */
193 #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
194 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
195 #define CONFIG_SYS_INIT_RAM_SIZE 0x800
197 /* FLASH and environment organization */
199 /* **** PISMO SUPPORT *** */
200 #define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */
202 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
203 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
205 #if defined(CONFIG_NAND)
206 #define CONFIG_SYS_FLASH_BASE NAND_BASE
209 /* Monitor at start of flash */
210 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
212 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
213 #define CONFIG_ENV_SIZE CONFIG_SYS_ENV_SECT_SIZE
214 #define CONFIG_ENV_OFFSET 0x260000
215 #define CONFIG_ENV_ADDR 0x260000
217 /* Defines for SPL */
218 #define CONFIG_SPL_FRAMEWORK
219 #undef CONFIG_SPL_TEXT_BASE
220 #define CONFIG_SPL_TEXT_BASE 0x40200000
222 #undef CONFIG_SPL_BSS_START_ADDR
223 #define CONFIG_SPL_BSS_START_ADDR 0x80000000
224 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
226 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
227 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
229 #define CONFIG_SPL_NAND_BASE
230 #define CONFIG_SPL_NAND_DRIVERS
231 #define CONFIG_SPL_NAND_ECC
233 #endif /* __CONFIG_H */