git.sur5r.net Git - u-boot/blob - include/configs/ea20.h

   1 /*
   2  * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
   3  *
   4  * Based on davinci_dvevm.h. Original Copyrights follow:
   5  *
   6  * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * Board
  16  */
  17 #define CONFIG_DRIVER_TI_EMAC
  18 #define CONFIG_USE_SPIFLASH
  19 #define CONFIG_SYS_USE_NAND
  20 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
  21 #define CONFIG_DRIVER_TI_EMAC_RMII_NO_NEGOTIATE
  22 #define CONFIG_PREBOOT
  23
  24 /*
  25  * SoC Configuration
  26  */
  27 #define CONFIG_SYS_CLK_FREQ             clk_get(DAVINCI_ARM_CLKID)
  28 #define CONFIG_SYS_OSCIN_FREQ           24000000
  29 #define CONFIG_SYS_TIMERBASE            DAVINCI_TIMER0_BASE
  30 #define CONFIG_SYS_HZ_CLOCK             clk_get(DAVINCI_AUXCLK_CLKID)
  31 #define CONFIG_SKIP_LOWLEVEL_INIT
  32 #define CONFIG_DA8XX_GPIO
  33
  34 /*
  35  * Memory Info
  36  */
  37 #define CONFIG_SYS_MALLOC_LEN   (0x10000 + 4*1024*1024) /* malloc() len */
  38 #define PHYS_SDRAM_1            DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
  39 #define PHYS_SDRAM_1_SIZE       (64 << 20) /* SDRAM size 64MB */
  40 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
  41
  42 /* memtest start addr */
  43 #define CONFIG_SYS_MEMTEST_START        (PHYS_SDRAM_1 + 0x2000000)
  44
  45 /* memtest will be run on 16MB */
  46 #define CONFIG_SYS_MEMTEST_END  (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
  47
  48 #define CONFIG_NR_DRAM_BANKS    1 /* we have 1 bank of DRAM */
  49
  50 /*
  51  * Serial Driver info
  52  */
  53 #define CONFIG_SYS_NS16550_SERIAL
  54 #define CONFIG_SYS_NS16550_REG_SIZE     -4      /* NS16550 register size */
  55 #define CONFIG_SYS_NS16550_COM1 DAVINCI_UART0_BASE /* Base address of UART0 */
  56 #define CONFIG_SYS_NS16550_CLK  clk_get(DAVINCI_UART2_CLKID)
  57 #define CONFIG_CONS_INDEX       1               /* use UART0 for console */
  58
  59 #define CONFIG_SPI
  60 #define CONFIG_SYS_SPI_BASE             DAVINCI_SPI1_BASE
  61 #define CONFIG_SYS_SPI_CLK              clk_get(DAVINCI_SPI1_CLKID)
  62 #define CONFIG_SF_DEFAULT_SPEED         30000000
  63 #define CONFIG_ENV_SPI_MAX_HZ   CONFIG_SF_DEFAULT_SPEED
  64
  65 /*
  66  * I2C Configuration
  67  */
  68 #define CONFIG_SYS_I2C
  69 #define CONFIG_SYS_I2C_DAVINCI
  70 #define CONFIG_SYS_DAVINCI_I2C_SPEED            100000
  71 #define CONFIG_SYS_DAVINCI_I2C_SLAVE   10 /* Bogus, master-only in U-Boot */
  72
  73 /*
  74  * Network & Ethernet Configuration
  75  */
  76 #ifdef CONFIG_DRIVER_TI_EMAC
  77 #define CONFIG_MII
  78 #define CONFIG_BOOTP_DNS
  79 #define CONFIG_BOOTP_DNS2
  80 #define CONFIG_BOOTP_SEND_HOSTNAME
  81 #define CONFIG_NET_RETRY_COUNT  10
  82 #endif
  83
  84 #ifdef CONFIG_USE_SPIFLASH
  85 #define CONFIG_ENV_SIZE                 (8 << 10)
  86 #define CONFIG_ENV_OFFSET               0x80000
  87 #define CONFIG_ENV_SECT_SIZE            (64 << 10)
  88 #endif
  89
  90 #if defined(CONFIG_VIDEO)
  91 #define CONFIG_VIDEO_DA8XX
  92 #define CONFIG_SPLASH_SCREEN_ALIGN
  93 #define CONFIG_VIDEO_LOGO
  94 #define CONFIG_VIDEO_BMP_RLE8
  95 #define CONFIG_VIDEO_BMP_LOGO
  96 #endif
  97
  98 /*
  99  * U-Boot general configuration
 100  */
 101 #define CONFIG_BOOTFILE         "uImage" /* Boot file name */
 102 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 103 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
 104 #define CONFIG_SYS_LOAD_ADDR    (PHYS_SDRAM_1 + 0x700000)
 105 #define CONFIG_AUTO_COMPLETE
 106 #define CONFIG_CMDLINE_EDITING
 107 #define CONFIG_SYS_LONGHELP
 108 #define CONFIG_MX_CYCLIC
 109
 110 /*
 111  * Linux Information
 112  */
 113 #define LINUX_BOOT_PARAM_ADDR   (PHYS_SDRAM_1 + 0x100)
 114 #define CONFIG_CMDLINE_TAG
 115 #define CONFIG_SETUP_MEMORY_TAGS
 116
 117 #ifdef CONFIG_CMD_BDI
 118 #define CONFIG_CLOCKS
 119 #endif
 120
 121 #ifndef CONFIG_DRIVER_TI_EMAC
 122 #endif
 123
 124 /* NAND Setup */
 125 #ifdef CONFIG_SYS_USE_NAND
 126 #define CONFIG_MTD_DEVICE
 127 #define CONFIG_MTD_PARTITIONS
 128
 129 #define CONFIG_NAND_DAVINCI
 130 #define CONFIG_SYS_NAND_PAGE_2K
 131 #define CONFIG_SYS_NAND_NO_SUBPAGE
 132 #define CONFIG_SYS_NAND_CS              2
 133 #define CONFIG_SYS_NAND_BASE            DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
 134 #undef CONFIG_SYS_NAND_HW_ECC
 135 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
 136 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 137 #define CONFIG_SYS_MAX_NAND_DEVICE      1 /* Max number of NAND devices */
 138 #endif
 139
 140 /* SPI Flash */
 141 #ifdef CONFIG_USE_SPIFLASH
 142 #endif
 143
 144 #if !defined(CONFIG_SYS_USE_NAND) && \
 145         !defined(CONFIG_USE_NOR) && \
 146         !defined(CONFIG_USE_SPIFLASH)
 147 #define CONFIG_ENV_SIZE         (16 << 10)
 148 #endif
 149
 150 /* additions for new relocation code, must added to all boards */
 151 #define CONFIG_SYS_SDRAM_BASE           0xc0000000
 152 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_SDRAM_BASE + 0x1000 - \
 153                                         GENERATED_GBL_DATA_SIZE)
 154 /*
 155  * Default environment and default scripts
 156  * to update uboot and load kernel
 157  */
 158
 159 #define CONFIG_HOSTNAME ea20
 160 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 161         "as=3\0"                                                        \
 162         "netdev=eth0\0"                                         \
 163         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 164                 "nfsroot=${serverip}:${rootpath}\0"                     \
 165         "rfsbargs=setenv bootargs root=/dev/nfs rw "                    \
 166         "nfsroot=${serverip}:${rfsbpath}\0"                             \
 167         "testrfsargs=setenv bootargs root=/dev/nfs rw "         \
 168         "nfsroot=${serverip}:${testrfspath}\0"                          \
 169         "ramargs=setenv bootargs root=/dev/ram rw initrd="              \
 170         "0x${ramdisk_addr_r},4M\0"                                      \
 171         "mtdids=nand0=davinci_nand.0\0"                         \
 172         "serverip=192.168.5.249\0"                                      \
 173         "ipaddr=192.168.5.248\0"                                        \
 174         "rootpath=/opt/eldk/arm\0"                                      \
 175         "splashpos=230,180\0"                                           \
 176         "testrfspath=/opt/eldk/test_arm\0"                              \
 177         "nandargs=setenv bootargs rootfstype=ubifs ro chk_data_crc "    \
 178         "ubi.mtd=${as} root=ubi0:rootfs\0"                              \
 179         "nandrwargs=setenv bootargs rootfstype=ubifs rw chk_data_crc "  \
 180         "ubi.mtd=${as} root=ubi0:rootfs\0"                              \
 181         "addip_sta=setenv bootargs ${bootargs} "                        \
 182                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 183                 ":${hostname}:${netdev}:off panic=1\0"                  \
 184         "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"               \
 185         "addip=if test -n ${ipdyn};then run addip_dyn;"         \
 186                 "else run addip_sta;fi\0"                               \
 187         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 188         "addtty=setenv bootargs ${bootargs}"                            \
 189                 " console=${consoledev},${baudrate}n8\0"                \
 190         "addmisc=setenv bootargs ${bootargs} ${misc}\0"         \
 191         "addmem=setenv bootargs ${bootargs} mem=${memory}\0"            \
 192         "consoledev=ttyS0\0"                                            \
 193         "loadaddr=c0000014\0"                                           \
 194         "memory=32M\0"                                                  \
 195         "kernel_addr_r=c0700000\0"                                      \
 196         "hostname=" __stringify(CONFIG_HOSTNAME) "\0"                   \
 197         "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0"            \
 198         "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/image.ext2\0"    \
 199         "flash_self=run ramargs addip addtty addmtd addmisc addmem;"    \
 200                         "bootm ${kernel_addr_r}\0"                      \
 201         "flash_nfs=run nfsargs addip addtty addmtd addmisc addmem;"     \
 202                 "bootm ${kernel_addr}\0"                                \
 203         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
 204                 "run nfsargs addip addtty addmtd addmisc addmem;"       \
 205                 "bootm ${kernel_addr_r}\0"                              \
 206         "net_rfsb=tftp ${kernel_addr_r} ${bootfile}; "                  \
 207                 "run rfsbargs addip addtty addmtd addmisc addmem; "     \
 208                 "bootm ${kernel_addr_r}\0"                              \
 209         "net_testrfs=tftp ${kernel_addr_r} ${bootfile}; "               \
 210                 "run testrfsargs addip addtty addmtd addmisc addmem; "  \
 211                 "bootm ${kernel_addr_r}\0"                              \
 212         "net_self_load=tftp ${kernel_addr_r} ${bootfile};"              \
 213                 "tftp ${ramdisk_addr_r} ${ramdisk_file};\0"             \
 214         "nand_nand=ubi part nand0,${as};ubifsmount ubi:rootfs;"         \
 215                 "ubifsload ${kernel_addr_r} /boot/uImage;"              \
 216                 "ubifsumount; run nandargs addip addtty "               \
 217                 "addmtd addmisc addmem;clrlogo;"                        \
 218                 "bootm ${kernel_addr_r}\0"                              \
 219         "nand_nandrw=ubi part nand0,${as};ubifsmount ubi:rootfs;"       \
 220                 "ubifsload ${kernel_addr_r} /boot/uImage;"              \
 221                 "ubifsumount; run nandrwargs addip addtty "             \
 222                 "addmtd addmisc addmem;clrlogo;"                        \
 223                 "bootm ${kernel_addr_r}\0"                              \
 224         "net_nandrw=tftp ${kernel_addr_r} ${bootfile}; run nandrwargs"  \
 225                 " addip addtty addmtd addmisc addmem;"                  \
 226                 "clrlogo;bootm ${kernel_addr_r}\0"                      \
 227         "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0"          \
 228         "load_magic=if sf probe 0;then sf "                             \
 229                 "read c0000000 0x10000 0x60000;fi\0"                    \
 230         "load_nand=ubi part nand0,${as};ubifsmount ubi:rootfs;"         \
 231                 "if ubifsload c0000014 /boot/u-boot.bin;"               \
 232                 "then mw c0000008 ${filesize};else echo Error reading"  \
 233                 " u-boot from nand!;fi\0"                               \
 234         "load_net=if sf probe 0;then sf read c0000000 0x10000 " \
 235                 "0x60000;tftp c0000014 ${u-boot};"                      \
 236                 "mw c0000008 ${filesize};fi\0"                          \
 237         "upd=if sf probe 0;then sf erase 10000 60000;"                  \
 238                 "sf write c0000000 10000 60000;fi\0"                    \
 239         "ublupdate=if tftp C0700000 ${ublname};then sf probe 0; "       \
 240                 "sf erase 0 10000;"                                     \
 241                 "sf write 0xc0700000 0 ${filesize};fi\0"                \
 242         "ubootupd_net=if run load_net;then echo Updating u-boot;"       \
 243                 "if run upd; then echo U-Boot updated;"         \
 244                         "else echo Error updating u-boot !;"            \
 245                         "echo Board without bootloader !!;"             \
 246                 "fi;"                                                   \
 247                 "else echo U-Boot not downloaded..exiting;fi\0" \
 248         "ubootupd_nand=echo run load_magic,run load_nand,run upd;\0"    \
 249         "bootcmd=run net_testrfs\0"
 250
 251 #include <asm/arch/hardware.h>
 252
 253 #endif /* __CONFIG_H */