git.sur5r.net Git - u-boot/blob - include/configs/ls1043a_common.h

   1 /*
   2  * Copyright (C) 2015 Freescale Semiconductor
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __LS1043A_COMMON_H
   8 #define __LS1043A_COMMON_H
   9
  10 /* SPL build */
  11 #ifdef CONFIG_SPL_BUILD
  12 #define SPL_NO_FMAN
  13 #define SPL_NO_DSPI
  14 #define SPL_NO_PCIE
  15 #define SPL_NO_ENV
  16 #define SPL_NO_MISC
  17 #define SPL_NO_USB
  18 #define SPL_NO_SATA
  19 #define SPL_NO_QE
  20 #define SPL_NO_EEPROM
  21 #endif
  22 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
  23 #define SPL_NO_MMC
  24 #endif
  25 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT_QSPI))
  26 #define SPL_NO_IFC
  27 #endif
  28
  29 #define CONFIG_REMAKE_ELF
  30 #define CONFIG_FSL_LAYERSCAPE
  31 #define CONFIG_MP
  32 #define CONFIG_GICV2
  33
  34 #include <asm/arch/stream_id_lsch2.h>
  35 #include <asm/arch/config.h>
  36
  37 /* Link Definitions */
  38 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  39
  40 #define CONFIG_SUPPORT_RAW_INITRD
  41
  42 #define CONFIG_SKIP_LOWLEVEL_INIT
  43
  44 #define CONFIG_VERY_BIG_RAM
  45 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  46 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  47 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  48 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL
  49
  50 #define CPU_RELEASE_ADDR               secondary_boot_func
  51
  52 /* Generic Timer Definitions */
  53 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  54
  55 /* Size of malloc() pool */
  56 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 1024 * 1024)
  57
  58 /* Serial Port */
  59 #define CONFIG_CONS_INDEX               1
  60 #define CONFIG_SYS_NS16550_SERIAL
  61 #define CONFIG_SYS_NS16550_REG_SIZE     1
  62 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  63
  64 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  65
  66 /* SD boot SPL */
  67 #ifdef CONFIG_SD_BOOT
  68 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  69
  70 #define CONFIG_SPL_TEXT_BASE            0x10000000
  71 #define CONFIG_SPL_MAX_SIZE             0x17000
  72 #define CONFIG_SPL_STACK                0x1001e000
  73 #define CONFIG_SPL_PAD_TO               0x1d000
  74
  75 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
  76                                         CONFIG_SPL_BSS_MAX_SIZE)
  77 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  78 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
  79 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
  80
  81 #ifdef CONFIG_SECURE_BOOT
  82 #define CONFIG_U_BOOT_HDR_SIZE                          (16 << 10)
  83 /*
  84  * HDR would be appended at end of image and copied to DDR along
  85  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  86  * size increases then increase this size in case of secure boot as
  87  * it uses raw u-boot image instead of fit image.
  88  */
  89 #define CONFIG_SYS_MONITOR_LEN          (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
  90 #else
  91 #define CONFIG_SYS_MONITOR_LEN          0x100000
  92 #endif /* ifdef CONFIG_SECURE_BOOT */
  93 #endif
  94
  95 /* NAND SPL */
  96 #ifdef CONFIG_NAND_BOOT
  97 #define CONFIG_SPL_PBL_PAD
  98 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  99 #define CONFIG_SPL_TEXT_BASE            0x10000000
 100 #define CONFIG_SPL_MAX_SIZE             0x1a000
 101 #define CONFIG_SPL_STACK                0x1001d000
 102 #define CONFIG_SYS_NAND_U_BOOT_DST      CONFIG_SYS_TEXT_BASE
 103 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 104 #define CONFIG_SYS_SPL_MALLOC_START     0x80200000
 105 #define CONFIG_SPL_BSS_START_ADDR       0x80100000
 106 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
 107 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 108
 109 #ifdef CONFIG_SECURE_BOOT
 110 #define CONFIG_U_BOOT_HDR_SIZE                          (16 << 10)
 111 #endif /* ifdef CONFIG_SECURE_BOOT */
 112
 113 #ifdef CONFIG_U_BOOT_HDR_SIZE
 114 /*
 115  * HDR would be appended at end of image and copied to DDR along
 116  * with U-Boot image. Here u-boot max. size is 512K. So if binary
 117  * size increases then increase this size in case of secure boot as
 118  * it uses raw u-boot image instead of fit image.
 119  */
 120 #define CONFIG_SYS_MONITOR_LEN          (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
 121 #else
 122 #define CONFIG_SYS_MONITOR_LEN          0x100000
 123 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
 124
 125 #endif
 126
 127 /* IFC */
 128 #ifndef SPL_NO_IFC
 129 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
 130 #define CONFIG_FSL_IFC
 131 /*
 132  * CONFIG_SYS_FLASH_BASE has the final address (core view)
 133  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
 134  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
 135  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
 136  */
 137 #define CONFIG_SYS_FLASH_BASE                   0x60000000
 138 #define CONFIG_SYS_FLASH_BASE_PHYS              CONFIG_SYS_FLASH_BASE
 139 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY        0x00000000
 140
 141 #ifdef CONFIG_MTD_NOR_FLASH
 142 #define CONFIG_FLASH_CFI_DRIVER
 143 #define CONFIG_SYS_FLASH_CFI
 144 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 145 #define CONFIG_SYS_FLASH_QUIET_TEST
 146 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
 147 #endif
 148 #endif
 149 #endif
 150
 151 /* I2C */
 152 #define CONFIG_SYS_I2C
 153 #define CONFIG_SYS_I2C_MXC
 154 #define CONFIG_SYS_I2C_MXC_I2C1
 155 #define CONFIG_SYS_I2C_MXC_I2C2
 156 #define CONFIG_SYS_I2C_MXC_I2C3
 157 #define CONFIG_SYS_I2C_MXC_I2C4
 158
 159 /* PCIe */
 160 #ifndef SPL_NO_PCIE
 161 #define CONFIG_PCIE1            /* PCIE controller 1 */
 162 #define CONFIG_PCIE2            /* PCIE controller 2 */
 163 #define CONFIG_PCIE3            /* PCIE controller 3 */
 164
 165 #ifdef CONFIG_PCI
 166 #define CONFIG_PCI_SCAN_SHOW
 167 #endif
 168 #endif
 169
 170 /* Command line configuration */
 171
 172 /*  MMC  */
 173 #ifndef SPL_NO_MMC
 174 #ifdef CONFIG_MMC
 175 #define CONFIG_FSL_ESDHC
 176 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 177 #endif
 178 #endif
 179
 180 /*  DSPI  */
 181 #ifndef SPL_NO_DSPI
 182 #define CONFIG_FSL_DSPI
 183 #ifdef CONFIG_FSL_DSPI
 184 #define CONFIG_DM_SPI_FLASH
 185 #define CONFIG_SPI_FLASH_STMICRO        /* cs0 */
 186 #define CONFIG_SPI_FLASH_SST            /* cs1 */
 187 #define CONFIG_SPI_FLASH_EON            /* cs2 */
 188 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
 189 #define CONFIG_SF_DEFAULT_BUS           1
 190 #define CONFIG_SF_DEFAULT_CS            0
 191 #endif
 192 #endif
 193 #endif
 194
 195 /* FMan ucode */
 196 #ifndef SPL_NO_FMAN
 197 #define CONFIG_SYS_DPAA_FMAN
 198 #ifdef CONFIG_SYS_DPAA_FMAN
 199 #define CONFIG_SYS_FM_MURAM_SIZE        0x60000
 200
 201 #ifdef CONFIG_NAND_BOOT
 202 /* Store Fman ucode at offeset 0x900000(72 blocks). */
 203 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 204 #define CONFIG_SYS_FMAN_FW_ADDR         (72 * CONFIG_SYS_NAND_BLOCK_SIZE)
 205 #elif defined(CONFIG_SD_BOOT)
 206 /*
 207  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 208  * about 1MB (2040 blocks), Env is stored after the image, and the env size is
 209  * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800).
 210  */
 211 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 212 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x4800)
 213 #define CONFIG_SYS_QE_FW_ADDR           (512 * 0x4a08)
 214 #elif defined(CONFIG_QSPI_BOOT)
 215 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 216 #define CONFIG_SYS_FMAN_FW_ADDR         0x40900000
 217 #define CONFIG_ENV_SPI_BUS              0
 218 #define CONFIG_ENV_SPI_CS               0
 219 #define CONFIG_ENV_SPI_MAX_HZ           1000000
 220 #define CONFIG_ENV_SPI_MODE             0x03
 221 #else
 222 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 223 /* FMan fireware Pre-load address */
 224 #define CONFIG_SYS_FMAN_FW_ADDR         0x60900000
 225 #define CONFIG_SYS_QE_FW_ADDR           0x60940000
 226 #endif
 227 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 228 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 229 #endif
 230 #endif
 231
 232 /* Miscellaneous configurable options */
 233 #define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
 234
 235 #define CONFIG_HWCONFIG
 236 #define HWCONFIG_BUFFER_SIZE            128
 237
 238 #ifndef SPL_NO_MISC
 239 #include <config_distro_defaults.h>
 240 #ifndef CONFIG_SPL_BUILD
 241 #define BOOT_TARGET_DEVICES(func) \
 242         func(MMC, mmc, 0) \
 243         func(USB, usb, 0)
 244 #include <config_distro_bootcmd.h>
 245 #endif
 246
 247 /* Initial environment variables */
 248 #define CONFIG_EXTRA_ENV_SETTINGS               \
 249         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 250         "fdt_high=0xffffffffffffffff\0"         \
 251         "initrd_high=0xffffffffffffffff\0"      \
 252         "fdt_addr=0x64f00000\0"                 \
 253         "kernel_addr=0x61000000\0"              \
 254         "scriptaddr=0x80000000\0"               \
 255         "scripthdraddr=0x80080000\0"            \
 256         "fdtheader_addr_r=0x80100000\0"         \
 257         "kernelheader_addr_r=0x80200000\0"      \
 258         "kernel_addr_r=0x81000000\0"            \
 259         "fdt_addr_r=0x90000000\0"               \
 260         "load_addr=0xa0000000\0"                \
 261         "kernelheader_addr=0x60800000\0"        \
 262         "kernel_size=0x2800000\0"               \
 263         "kernelheader_size=0x40000\0"           \
 264         "kernel_addr_sd=0x8000\0"               \
 265         "kernel_size_sd=0x14000\0"              \
 266         "kernelhdr_addr_sd=0x4000\0"            \
 267         "kernelhdr_size_sd=0x10\0"              \
 268         "console=ttyS0,115200\0"                \
 269         "boot_os=y\0"                           \
 270         "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"        \
 271         BOOTENV                                 \
 272         "boot_scripts=ls1043ardb_boot.scr\0"    \
 273         "boot_script_hdr=hdr_ls1043ardb_bs.out\0"       \
 274         "scan_dev_for_boot_part="               \
 275                 "part list ${devtype} ${devnum} devplist; "     \
 276                 "env exists devplist || setenv devplist 1; "    \
 277                 "for distro_bootpart in ${devplist}; do "       \
 278                         "if fstype ${devtype} "                 \
 279                                 "${devnum}:${distro_bootpart} " \
 280                                 "bootfstype; then "             \
 281                                 "run scan_dev_for_boot; "       \
 282                         "fi; "                                  \
 283                 "done\0"                        \
 284         "scan_dev_for_boot="                                    \
 285                 "echo Scanning ${devtype} "                     \
 286                         "${devnum}:${distro_bootpart}...; "     \
 287                 "for prefix in ${boot_prefixes}; do "           \
 288                         "run scan_dev_for_scripts; "            \
 289                 "done;\0"                                       \
 290         "boot_a_script="                                        \
 291                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 292                         "${scriptaddr} ${prefix}${script}; "    \
 293                 "env exists secureboot && load ${devtype} "     \
 294                         "${devnum}:${distro_bootpart} "         \
 295                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 296                         "&& esbc_validate ${scripthdraddr};"    \
 297                 "source ${scriptaddr}\0"                        \
 298         "qspi_bootcmd=echo Trying load from qspi..;"    \
 299                 "sf probe && sf read $load_addr "       \
 300                 "$kernel_addr $kernel_size; env exists secureboot "     \
 301                 "&& sf read $kernelheader_addr_r $kernelheader_addr "   \
 302                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 303                 "bootm $load_addr#$board\0"     \
 304         "nor_bootcmd=echo Trying load from nor..;"      \
 305                 "cp.b $kernel_addr $load_addr " \
 306                 "$kernel_size; env exists secureboot "  \
 307                 "&& cp.b $kernelheader_addr $kernelheader_addr_r "      \
 308                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 309                 "bootm $load_addr#$board\0"         \
 310         "sd_bootcmd=echo Trying load from SD ..;"       \
 311                 "mmcinfo; mmc read $load_addr "         \
 312                 "$kernel_addr_sd $kernel_size_sd && "     \
 313                 "env exists secureboot && mmc read $kernelheader_addr_r "               \
 314                 "$kernelhdr_addr_sd $kernelhdr_size_sd "                \
 315                 " && esbc_validate ${kernelheader_addr_r};"     \
 316                 "bootm $load_addr#$board\0"
 317
 318
 319 #undef CONFIG_BOOTCOMMAND
 320 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 321 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; "     \
 322                            "env exists secureboot && esbc_halt;"
 323 #elif defined(CONFIG_SD_BOOT)
 324 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; "  \
 325                            "env exists secureboot && esbc_halt;"
 326 #else
 327 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run nor_bootcmd; "      \
 328                            "env exists secureboot && esbc_halt;"
 329 #endif
 330 #endif
 331
 332 /* Monitor Command Prompt */
 333 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 334 #define CONFIG_SYS_LONGHELP
 335
 336 #ifndef SPL_NO_MISC
 337 #ifndef CONFIG_CMDLINE_EDITING
 338 #define CONFIG_CMDLINE_EDITING          1
 339 #endif
 340 #endif
 341
 342 #define CONFIG_AUTO_COMPLETE
 343 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 344
 345 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 346
 347 #include <asm/arch/soc.h>
 348
 349 #endif /* __LS1043A_COMMON_H */