git.sur5r.net Git - u-boot/blob - include/configs/tqma6.h

   1 /*
   2  * Copyright (C) 2013, 2014, 2017 Markus Niebel <Markus.Niebel@tq-group.com>
   3  *
   4  * Configuration settings for the TQ Systems TQMa6<Q,D,DL,S> module.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 #include <linux/kconfig.h>
  13 /* SPL */
  14 /* #if defined(CONFIG_SPL_BUILD) */
  15 /* common IMX6 SPL configuration */
  16 #include "imx6_spl.h"
  17
  18 /* #endif */
  19
  20 /* place code in last 4 MiB of RAM */
  21
  22 #include "mx6_common.h"
  23
  24 #if defined(CONFIG_TQMA6S)
  25 #define PHYS_SDRAM_SIZE                 (512u * SZ_1M)
  26 #elif defined(CONFIG_TQMA6DL)
  27 #define PHYS_SDRAM_SIZE                 (SZ_1G)
  28 #elif defined(CONFIG_TQMA6Q)
  29 #define PHYS_SDRAM_SIZE                 (SZ_1G)
  30 #endif
  31
  32 #define CONFIG_MXC_UART
  33
  34 /* SPI Flash */
  35
  36 #define TQMA6_SPI_FLASH_SECTOR_SIZE     SZ_64K
  37
  38 #define CONFIG_SF_DEFAULT_BUS   0
  39 #define CONFIG_SF_DEFAULT_CS    0
  40 #define CONFIG_SF_DEFAULT_SPEED 50000000
  41 #define CONFIG_SF_DEFAULT_MODE  (SPI_MODE_0)
  42
  43 /* I2C Configs */
  44 #define CONFIG_SYS_I2C
  45 #define CONFIG_SYS_I2C_MXC
  46 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  47 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  48 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  49 #define CONFIG_I2C_MULTI_BUS
  50 #define CONFIG_SYS_I2C_SPEED            100000
  51
  52 /* I2C EEPROM (M24C64) */
  53 #define CONFIG_SYS_I2C_EEPROM_ADDR                      0x50
  54 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN                  2
  55 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS           5 /* 32 Bytes */
  56 #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS       20
  57
  58 #define CONFIG_POWER
  59 #define CONFIG_POWER_I2C
  60 #define CONFIG_POWER_PFUZE100
  61 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  62 #define TQMA6_PFUZE100_I2C_BUS          2
  63
  64 /* MMC Configs */
  65 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  66
  67 /* USB Configs */
  68 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  69 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  70 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
  71
  72 #define CONFIG_FEC_MXC
  73 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  74 #define CONFIG_MII
  75
  76 #define CONFIG_ARP_TIMEOUT              200UL
  77
  78 #define CONFIG_ENV_SIZE                 (SZ_8K)
  79 /* Size of malloc() pool */
  80 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 2 * SZ_1M)
  81
  82 #if defined(CONFIG_TQMA6X_MMC_BOOT)
  83
  84 #define TQMA6_UBOOT_OFFSET              SZ_1K
  85 #define TQMA6_UBOOT_SECTOR_START        0x2
  86 #define TQMA6_UBOOT_SECTOR_COUNT        0x7fe
  87
  88 #define CONFIG_ENV_OFFSET               SZ_1M
  89 #define CONFIG_SYS_MMC_ENV_DEV          0
  90
  91 #define TQMA6_FDT_OFFSET                (2 * SZ_1M)
  92 #define TQMA6_FDT_SECTOR_START          0x1000
  93 #define TQMA6_FDT_SECTOR_COUNT          0x800
  94
  95 #define TQMA6_KERNEL_SECTOR_START       0x2000
  96 #define TQMA6_KERNEL_SECTOR_COUNT       0x2000
  97
  98 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
  99         "uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0"                \
 100         "uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"                 \
 101         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 102         "fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                     \
 103         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 104         "kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"               \
 105         "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0"                       \
 106         "loadimage=mmc dev ${mmcdev}; "                                        \
 107                 "mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0"       \
 108         "loadfdt=mmc dev ${mmcdev}; "                                          \
 109                 "mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0"             \
 110         "update_uboot=if tftp ${uboot}; then "                                 \
 111                 "if itest ${filesize} > 0; then "                              \
 112                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 113                         "setexpr blkc ${filesize} + 0x1ff; "                   \
 114                         "setexpr blkc ${blkc} / 0x200; "                       \
 115                         "if itest ${blkc} <= ${uboot_size}; then "             \
 116                                 "mmc write ${loadaddr} ${uboot_start} "        \
 117                                         "${blkc}; "                            \
 118                         "fi; "                                                 \
 119                 "fi; fi; "                                                     \
 120                 "setenv filesize; setenv blkc \0"                              \
 121         "update_kernel=run kernel_name; "                                      \
 122                 "if tftp ${kernel}; then "                                     \
 123                         "if itest ${filesize} > 0; then "                      \
 124                                 "mmc dev ${mmcdev}; mmc rescan; "              \
 125                                 "setexpr blkc ${filesize} + 0x1ff; "           \
 126                                 "setexpr blkc ${blkc} / 0x200; "               \
 127                                 "if itest ${blkc} <= ${kernel_size}; then "    \
 128                                         "mmc write ${loadaddr} "               \
 129                                                 "${kernel_start} ${blkc}; "    \
 130                                 "fi; "                                         \
 131                         "fi; "                                                 \
 132                 "fi; "                                                         \
 133                 "setenv filesize; setenv blkc \0"                              \
 134         "update_fdt=if tftp ${fdt_file}; then "                                \
 135                 "if itest ${filesize} > 0; then "                              \
 136                         "mmc dev ${mmcdev}; mmc rescan; "                      \
 137                         "setexpr blkc ${filesize} + 0x1ff; "                   \
 138                         "setexpr blkc ${blkc} / 0x200; "                       \
 139                         "if itest ${blkc} <= ${fdt_size}; then "               \
 140                                 "mmc write ${loadaddr} ${fdt_start} ${blkc}; " \
 141                         "fi; "                                                 \
 142                 "fi; fi; "                                                     \
 143                 "setenv filesize; setenv blkc \0"                              \
 144
 145 #define CONFIG_BOOTCOMMAND \
 146         "run mmcboot; run netboot; run panicboot"
 147
 148 #elif defined(CONFIG_TQMA6X_SPI_BOOT)
 149
 150 #define TQMA6_UBOOT_OFFSET              0x400
 151 #define TQMA6_UBOOT_SECTOR_START        0x0
 152 /* max u-boot size: 512k */
 153 #define TQMA6_UBOOT_SECTOR_SIZE         TQMA6_SPI_FLASH_SECTOR_SIZE
 154 #define TQMA6_UBOOT_SECTOR_COUNT        0x8
 155 #define TQMA6_UBOOT_SIZE                (TQMA6_UBOOT_SECTOR_SIZE * \
 156                                          TQMA6_UBOOT_SECTOR_COUNT)
 157
 158 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 159 #define CONFIG_ENV_OFFSET               (TQMA6_UBOOT_SIZE)
 160 #define CONFIG_ENV_SECT_SIZE            TQMA6_SPI_FLASH_SECTOR_SIZE
 161 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + \
 162                                          CONFIG_ENV_SECT_SIZE)
 163
 164 #define CONFIG_ENV_SPI_BUS              (CONFIG_SF_DEFAULT_BUS)
 165 #define CONFIG_ENV_SPI_CS               (CONFIG_SF_DEFAULT_CS)
 166 #define CONFIG_ENV_SPI_MAX_HZ           (CONFIG_SF_DEFAULT_SPEED)
 167 #define CONFIG_ENV_SPI_MODE             (CONFIG_SF_DEFAULT_MODE)
 168
 169 #define TQMA6_FDT_OFFSET                (CONFIG_ENV_OFFSET_REDUND + \
 170                                          CONFIG_ENV_SECT_SIZE)
 171 #define TQMA6_FDT_SECT_SIZE             (TQMA6_SPI_FLASH_SECTOR_SIZE)
 172
 173 #define TQMA6_FDT_SECTOR_START          0x0a /* 8 Sector u-boot, 2 Sector env */
 174 #define TQMA6_FDT_SECTOR_COUNT          0x01
 175
 176 #define TQMA6_KERNEL_SECTOR_START       0x10
 177 #define TQMA6_KERNEL_SECTOR_COUNT       0x60
 178
 179 #define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                       \
 180         "mmcblkdev=0\0"                                                        \
 181         "uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0"                     \
 182         "uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0"              \
 183         "fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0"                    \
 184         "fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0"                  \
 185         "kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0"              \
 186         "kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0"            \
 187         "update_uboot=if tftp ${uboot}; then "                                 \
 188                 "if itest ${filesize} > 0; then "                              \
 189                         "setexpr blkc ${filesize} + "                          \
 190                                 __stringify(TQMA6_UBOOT_OFFSET) "; "           \
 191                         "setexpr size ${uboot_sectors} * "                     \
 192                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 193                         "if itest ${blkc} <= ${size}; then "                   \
 194                                 "sf probe; "                                   \
 195                                 "sf erase 0 ${size}; "                         \
 196                                 "sf write ${loadaddr} ${uboot_offset} "        \
 197                                         "${filesize}; "                        \
 198                         "fi; "                                                 \
 199                 "fi; fi; "                                                     \
 200                 "setenv filesize 0; setenv blkc; setenv size \0"               \
 201         "update_kernel=run kernel_name; if tftp ${kernel}; then "              \
 202                 "if itest ${filesize} > 0; then "                              \
 203                         "setexpr size ${kernel_sectors} * "                    \
 204                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 205                         "setexpr offset ${kernel_start} * "                    \
 206                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 207                         "if itest ${filesize} <= ${size}; then "               \
 208                                 "sf probe; "                                   \
 209                                 "sf erase ${offset} ${size}; "                 \
 210                                 "sf write ${loadaddr} ${offset} "              \
 211                                         "${filesize}; "                        \
 212                         "fi; "                                                 \
 213                 "fi; fi; "                                                     \
 214                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 215         "update_fdt=if tftp ${fdt_file}; then "                                \
 216                 "if itest ${filesize} > 0; then "                              \
 217                         "setexpr size ${fdt_sectors} * "                       \
 218                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 219                         "setexpr offset ${fdt_start} * "                       \
 220                                 __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "   \
 221                         "if itest ${filesize} <= ${size}; then "               \
 222                                 "sf probe; "                                   \
 223                                 "sf erase ${offset} ${size}; "                 \
 224                                 "sf write ${loadaddr} ${offset} "              \
 225                                         "${filesize}; "                        \
 226                         "fi; "                                                 \
 227                 "fi; fi; "                                                     \
 228                 "setenv filesize 0; setenv size ; setenv offset\0"             \
 229         "loadimage=sf probe; "                                                 \
 230                 "setexpr size ${kernel_sectors} * "                            \
 231                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 232                 "setexpr offset ${kernel_start} * "                            \
 233                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 234                 "sf read ${loadaddr} ${offset} ${size}; "                      \
 235                 "setenv size ; setenv offset\0"                                \
 236         "loadfdt=sf probe; "                                                   \
 237                 "setexpr size ${fdt_sectors} * "                               \
 238                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 239                 "setexpr offset ${fdt_start} * "                               \
 240                         __stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; "           \
 241                 "sf read ${fdt_addr} ${offset} ${size}; "                      \
 242                 "setenv size ; setenv offset\0"                                \
 243
 244 #define CONFIG_BOOTCOMMAND                                                     \
 245         "sf probe; run mmcboot; run netboot; run panicboot"                    \
 246
 247 #else
 248
 249 #error "need to define boot source"
 250
 251 #endif
 252
 253 /* 128 MiB offset as in ARM related docu for linux suggested */
 254 #define TQMA6_FDT_ADDRESS               0x18000000
 255
 256 /* set to a resonable value, changeable by user */
 257 #define TQMA6_CMA_SIZE                 160M
 258
 259 #define CONFIG_EXTRA_ENV_SETTINGS                                              \
 260         "board=tqma6\0"                                                        \
 261         "uimage=uImage\0"                                                      \
 262         "zimage=zImage\0"                                                      \
 263         "boot_type=bootz\0"                                                    \
 264         "kernel_name=if test \"${boot_type}\" != bootz; then "                 \
 265                 "setenv kernel ${uimage}; "                                    \
 266                 "else setenv kernel ${zimage}; fi\0"                           \
 267         "uboot=u-boot.imx\0"                                                   \
 268         "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0"                               \
 269         "fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0"                          \
 270         "console=" CONSOLE_DEV "\0"                                            \
 271         "cma_size="__stringify(TQMA6_CMA_SIZE)"\0"                             \
 272         "fdt_high=0xffffffff\0"                                                \
 273         "initrd_high=0xffffffff\0"                                             \
 274         "rootfsmode=ro\0"                                                      \
 275         "addcma=setenv bootargs ${bootargs} cma=${cma_size}\0"                 \
 276         "addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0"  \
 277         "addfb=setenv bootargs ${bootargs} "                                   \
 278                 "imx-fbdev.legacyfb_depth=32 consoleblank=0\0"                 \
 279         "mmcpart=2\0"                                                          \
 280         "mmcblkdev=0\0"                                                        \
 281         "mmcargs=run addmmc addtty addfb addcma\0"                             \
 282         "addmmc=setenv bootargs ${bootargs} "                                  \
 283                 "root=/dev/mmcblk${mmcblkdev}p${mmcpart} ${rootfsmode} "       \
 284                 "rootwait\0"                                                   \
 285         "mmcboot=echo Booting from mmc ...; "                                  \
 286                 "setenv bootargs; "                                            \
 287                 "run mmcargs; "                                                \
 288                 "run loadimage; "                                              \
 289                 "if run loadfdt; then "                                        \
 290                         "echo boot device tree kernel ...; "                   \
 291                         "${boot_type} ${loadaddr} - ${fdt_addr}; "             \
 292                 "else "                                                        \
 293                         "${boot_type}; "                                       \
 294                 "fi;\0"                                                        \
 295                 "setenv bootargs \0"                                           \
 296         "netdev=eth0\0"                                                        \
 297         "rootpath=/srv/nfs/tqma6\0"                                            \
 298         "ipmode=static\0"                                                      \
 299         "netargs=run addnfs addip addtty addfb addcma\0"                       \
 300         "addnfs=setenv bootargs ${bootargs} "                                  \
 301                 "root=/dev/nfs rw "                                            \
 302                 "nfsroot=${serverip}:${rootpath},v3,tcp;\0"                    \
 303         "addip_static=setenv bootargs ${bootargs} "                            \
 304                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:"            \
 305                 "${hostname}:${netdev}:off\0"                                  \
 306         "addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0"                  \
 307         "addip=if test \"${ipmode}\" != static; then "                         \
 308                 "run addip_dynamic; else run addip_static; fi\0"               \
 309         "set_getcmd=if test \"${ipmode}\" != static; then "                    \
 310                 "setenv getcmd dhcp; setenv autoload yes; "                    \
 311                 "else setenv getcmd tftp; setenv autoload no; fi\0"            \
 312         "netboot=echo Booting from net ...; "                                  \
 313                 "run kernel_name; "                                            \
 314                 "run set_getcmd; "                                             \
 315                 "setenv bootargs; "                                            \
 316                 "run netargs; "                                                \
 317                 "if ${getcmd} ${kernel}; then "                                \
 318                         "if ${getcmd} ${fdt_addr} ${fdt_file}; then "          \
 319                                 "${boot_type} ${loadaddr} - ${fdt_addr}; "     \
 320                         "fi; "                                                 \
 321                 "fi; "                                                         \
 322                 "echo ... failed\0"                                            \
 323         "panicboot=echo No boot device !!! reset\0"                            \
 324         TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS                                      \
 325
 326 /* Physical Memory Map */
 327 #define CONFIG_NR_DRAM_BANKS            1
 328 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 329
 330 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 331 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 332 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 333
 334 #define CONFIG_SYS_INIT_SP_OFFSET \
 335         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 336 #define CONFIG_SYS_INIT_SP_ADDR \
 337         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 338
 339 /*
 340  * All the defines above are for the TQMa6 SoM
 341  *
 342  * Now include the baseboard specific configuration
 343  */
 344 #ifdef CONFIG_MBA6
 345 #include "tqma6_mba6.h"
 346 #elif CONFIG_WRU4
 347 #include "tqma6_wru4.h"
 348 #else
 349 #error "No baseboard for the TQMa6 defined!"
 350 #endif
 351
 352 /* Support at least the sensor on TQMa6 SOM */
 353
 354 #endif /* __CONFIG_H */