]> git.sur5r.net Git - u-boot/commitdiff
mx53loco: Improve error handling on power_init()
authorFabio Estevam <fabio.estevam@freescale.com>
Fri, 28 Dec 2012 04:05:29 +0000 (04:05 +0000)
committerStefano Babic <sbabic@denx.de>
Sat, 5 Jan 2013 17:07:53 +0000 (18:07 +0100)
Make the error handling more robust.

Check if each one of the PMIC writes fail and if they do, just return
immediately.

Also, print the cause for the failures.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
board/freescale/mx53loco/mx53loco.c

index b1bfb903896d7d818c8c5f6d93ac7eaa559c17ba..60cd4f0cfbae4388461a938b97e559dbef0f4d42 100644 (file)
@@ -343,7 +343,7 @@ static void setup_iomux_i2c(void)
 static int power_init(void)
 {
        unsigned int val;
-       int ret = -1;
+       int ret;
        struct pmic *p;
 
        if (!i2c_probe(CONFIG_SYS_DIALOG_PMIC_I2C_ADDR)) {
@@ -358,14 +358,33 @@ static int power_init(void)
                /* Set VDDA to 1.25V */
                val = DA9052_BUCKCORE_BCOREEN | DA_BUCKCORE_VBCORE_1_250V;
                ret = pmic_reg_write(p, DA9053_BUCKCORE_REG, val);
+               if (ret) {
+                       printf("Writing to BUCKCORE_REG failed: %d\n", ret);
+                       return ret;
+               }
 
-               ret |= pmic_reg_read(p, DA9053_SUPPLY_REG, &val);
+               pmic_reg_read(p, DA9053_SUPPLY_REG, &val);
                val |= DA9052_SUPPLY_VBCOREGO;
-               ret |= pmic_reg_write(p, DA9053_SUPPLY_REG, val);
+               ret = pmic_reg_write(p, DA9053_SUPPLY_REG, val);
+               if (ret) {
+                       printf("Writing to SUPPLY_REG failed: %d\n", ret);
+                       return ret;
+               }
 
                /* Set Vcc peripheral to 1.30V */
-               ret |= pmic_reg_write(p, DA9053_BUCKPRO_REG, 0x62);
-               ret |= pmic_reg_write(p, DA9053_SUPPLY_REG, 0x62);
+               ret = pmic_reg_write(p, DA9053_BUCKPRO_REG, 0x62);
+               if (ret) {
+                       printf("Writing to BUCKPRO_REG failed: %d\n", ret);
+                       return ret;
+               }
+
+               ret = pmic_reg_write(p, DA9053_SUPPLY_REG, 0x62);
+               if (ret) {
+                       printf("Writing to SUPPLY_REG failed: %d\n", ret);
+                       return ret;
+               }
+
+               return ret;
        }
 
        if (!i2c_probe(CONFIG_SYS_FSL_PMIC_I2C_ADDR)) {
@@ -381,28 +400,50 @@ static int power_init(void)
                pmic_reg_read(p, REG_SW_0, &val);
                val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_250V_MC34708;
                ret = pmic_reg_write(p, REG_SW_0, val);
+               if (ret) {
+                       printf("Writing to REG_SW_0 failed: %d\n", ret);
+                       return ret;
+               }
 
                /* Set VCC as 1.30V on SW2 */
                pmic_reg_read(p, REG_SW_1, &val);
                val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_300V_MC34708;
-               ret |= pmic_reg_write(p, REG_SW_1, val);
+               ret = pmic_reg_write(p, REG_SW_1, val);
+               if (ret) {
+                       printf("Writing to REG_SW_1 failed: %d\n", ret);
+                       return ret;
+               }
 
                /* Set global reset timer to 4s */
                pmic_reg_read(p, REG_POWER_CTL2, &val);
                val = (val & ~TIMER_MASK_MC34708) | TIMER_4S_MC34708;
-               ret |= pmic_reg_write(p, REG_POWER_CTL2, val);
+               ret = pmic_reg_write(p, REG_POWER_CTL2, val);
+               if (ret) {
+                       printf("Writing to REG_POWER_CTL2 failed: %d\n", ret);
+                       return ret;
+               }
 
                /* Set VUSBSEL and VUSBEN for USB PHY supply*/
                pmic_reg_read(p, REG_MODE_0, &val);
                val |= (VUSBSEL_MC34708 | VUSBEN_MC34708);
-               ret |= pmic_reg_write(p, REG_MODE_0, val);
+               ret = pmic_reg_write(p, REG_MODE_0, val);
+               if (ret) {
+                       printf("Writing to REG_MODE_0 failed: %d\n", ret);
+                       return ret;
+               }
 
                /* Set SWBST to 5V in auto mode */
                val = SWBST_AUTO;
-               ret |= pmic_reg_write(p, SWBST_CTRL, val);
+               ret = pmic_reg_write(p, SWBST_CTRL, val);
+               if (ret) {
+                       printf("Writing to SWBST_CTRL failed: %d\n", ret);
+                       return ret;
+               }
+
+               return ret;
        }
 
-       return ret;
+       return -1;
 }
 
 static void clock_1GHz(void)