sun50i-a64-olinuxino.dtb \
sun50i-a64-orangepi-win.dtb \
sun50i-a64-pine64-plus.dtb \
- sun50i-a64-pine64.dtb
+ sun50i-a64-pine64.dtb \
+ sun50i-a64-sopine-baseboard.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
sun9i-a80-cubieboard4.dtb \
--- /dev/null
+/*
+ * Copyright 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * AXP803 Integrated Power Management Chip
+ * http://files.pine64.org/doc/datasheet/pine64/AXP803_Datasheet_V1.0.pdf
+ */
+
+&axp803 {
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ regulators {
+ /* Default work frequency for buck regulators */
+ x-powers,dcdc-freq = <3000>;
+
+ reg_aldo1: aldo1 {
+ regulator-name = "aldo1";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-name = "aldo2";
+ };
+
+ reg_aldo3: aldo3 {
+ regulator-name = "aldo3";
+ };
+
+ reg_dc1sw: dc1sw {
+ regulator-name = "dc1sw";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-name = "dcdc1";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-name = "dcdc2";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-name = "dcdc3";
+ };
+
+ reg_dcdc4: dcdc4 {
+ regulator-name = "dcdc4";
+ };
+
+ reg_dcdc5: dcdc5 {
+ regulator-name = "dcdc5";
+ };
+
+ reg_dcdc6: dcdc6 {
+ regulator-name = "dcdc6";
+ };
+
+ reg_dldo1: dldo1 {
+ regulator-name = "dldo1";
+ };
+
+ reg_dldo2: dldo2 {
+ regulator-name = "dldo2";
+ };
+
+ reg_dldo3: dldo3 {
+ regulator-name = "dldo3";
+ };
+
+ reg_dldo4: dldo4 {
+ regulator-name = "dldo4";
+ };
+
+ reg_eldo1: eldo1 {
+ regulator-name = "eldo1";
+ };
+
+ reg_eldo2: eldo2 {
+ regulator-name = "eldo2";
+ };
+
+ reg_eldo3: eldo3 {
+ regulator-name = "eldo3";
+ };
+
+ reg_fldo1: fldo1 {
+ regulator-name = "fldo1";
+ };
+
+ reg_fldo2: fldo2 {
+ regulator-name = "fldo2";
+ };
+
+ reg_ldo_io0: ldo-io0 {
+ regulator-name = "ldo-io0";
+ status = "disabled";
+ };
+
+ reg_ldo_io1: ldo-io1 {
+ regulator-name = "ldo-io1";
+ status = "disabled";
+ };
+
+ reg_rtc_ldo: rtc-ldo {
+ /* RTC_LDO is a fixed, always-on regulator */
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "rtc-ldo";
+ };
+
+ reg_drivevbus: drivevbus {
+ regulator-name = "drivevbus";
+ status = "disabled";
+ };
+ };
+};
/*
* Copyright (c) 2016 ARM Ltd.
- * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
compatible = "sinovoip,bananapi-m64", "allwinner,sun50i-a64";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
serial1 = &uart1;
};
stdout-path = "serial0:115200n8";
};
- reg_vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ leds {
+ compatible = "gpio-leds";
+
+ pwr-led {
+ label = "bananapi-m64:red:pwr";
+ gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+ default-state = "on";
+ };
+
+ green {
+ label = "bananapi-m64:green:user";
+ gpios = <&pio 4 14 GPIO_ACTIVE_HIGH>; /* PE14 */
+ };
+
+ blue {
+ label = "bananapi-m64:blue:user";
+ gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
};
};
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_dc1sw>;
+ status = "okay";
+};
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
bias-pull-up;
};
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <®_vcc3v3>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
disable-wp;
bus-width = <4>;
status = "okay";
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dldo2>;
+ vqmmc-supply = <®_dldo4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+ interrupt-names = "host-wake";
+ };
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
status = "okay";
};
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
+ };
+};
+
+#include "axp803.dtsi"
+
+®_aldo1 {
+ /*
+ * This regulator also drives the PE pingroup GPIOs,
+ * which also controls two LEDs.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "afvcc-csi";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc1sw {
+ /*
+ * This regulator also indirectly drives the PD pingroup GPIOs,
+ * which also controls the power LED.
+ */
+ regulator-always-on;
+ regulator-name = "vcc-phy";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1040000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi-dsi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "cpvdd";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+®_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
&usbphy {
usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ usb0_vbus-supply = <®_drivevbus>;
status = "okay";
};
chosen {
stdout-path = "serial0:115200n8";
};
-
- reg_vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
};
&ehci0 {
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <®_vcc3v3>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
disable-wp;
bus-width = <4>;
status = "okay";
status = "okay";
};
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp803.dtsi"
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1040000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi-dsi";
+};
+
+®_dldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pg-wifi-io";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "cpvdd";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+®_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
stdout-path = "serial0:115200n8";
};
- reg_vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <®_vcc3v3>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
disable-wp;
bus-width = <4>;
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <®_aldo2>;
+ vqmmc-supply = <®_dldo4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ rtl8723bs: wifi@1 {
+ reg = <1>;
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp803.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc-pe";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1040000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-ddr3";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-mipi";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc-avdd-csi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "cpvdd";
+};
+
+®_eldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dvdd-csi";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+®_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
chosen {
stdout-path = "serial0:115200n8";
};
-
- reg_vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
};
&ehci1 {
- status = "okay";
+ status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <®_vcc3v3>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
status = "okay";
};
&ohci1 {
- status = "okay";
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp803.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "afvcc-csi";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1040000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi-dsi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avdd-csi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "cpvdd";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+®_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
};
&uart0 {
};
&usbphy {
- status = "okay";
+ status = "okay";
};
+
+++ /dev/null
-/ {
- aliases {
- ethernet0 = &emac;
- };
-
- soc {
- syscon: syscon@1c00000 {
- compatible = "allwinner,sun50i-a64-system-controller",
- "syscon";
- reg = <0x01c00000 0x1000>;
- };
-
- emac: ethernet@1c30000 {
- compatible = "allwinner,sun50i-a64-emac";
- syscon = <&syscon>;
- reg = <0x01c30000 0x10000>;
- interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "macirq";
- resets = <&ccu RST_BUS_EMAC>;
- reset-names = "stmmaceth";
- clocks = <&ccu CLK_BUS_EMAC>;
- clock-names = "stmmaceth";
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&rgmii_pins>;
- phy-mode = "rgmii";
- phy-handle = <&ext_rgmii_phy>;
- status = "okay";
-
- mdio: mdio {
- compatible = "snps,dwmac-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
- ext_rgmii_phy: ethernet-phy@1 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <1>;
- };
- };
- };
- };
-};
-
-&pio {
- rmii_pins: rmii_pins {
- pins = "PD10", "PD11", "PD13", "PD14", "PD17",
- "PD18", "PD19", "PD20", "PD22", "PD23";
- function = "emac";
- drive-strength = <40>;
- };
-
- rgmii_pins: rgmii_pins {
- pins = "PD8", "PD9", "PD10", "PD11", "PD12",
- "PD13", "PD15", "PD16", "PD17", "PD18",
- "PD19", "PD20", "PD21", "PD22", "PD23";
- function = "emac";
- drive-strength = <40>;
- };
-};
model = "Pine64+";
compatible = "pine64,pine64-plus", "allwinner,sun50i-a64";
- /* TODO: Camera, Ethernet PHY, touchscreen, etc. */
+ /* TODO: Camera, touchscreen, etc. */
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ status = "okay";
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
};
compatible = "pine64,pine64", "allwinner,sun50i-a64";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ serial3 = &uart3;
+ serial4 = &uart4;
};
chosen {
stdout-path = "serial0:115200n8";
};
+};
- reg_vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
+&ehci0 {
+ status = "okay";
};
&ehci1 {
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rmii_pins>;
+ phy-mode = "rmii";
+ phy-handle = <&ext_rmii_phy1>;
+ phy-supply = <®_dc1sw>;
+ status = "okay";
+
+};
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
bias-pull-up;
};
+&mdio {
+ ext_rmii_phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <®_vcc3v3>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
disable-wp;
bus-width = <4>;
status = "okay";
};
+&ohci0 {
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp803.dtsi"
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-phy";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1040000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+/*
+ * The DRAM chips used by Pine64 boards are DDR3L-compatible, so they can
+ * work at 1.35V with less power consumption.
+ * As AXP803 DCDC5 cannot reach 1.35V accurately, use 1.36V instead.
+ */
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1360000>;
+ regulator-max-microvolt = <1360000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-mipi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "cpvdd";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+®_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+/* On Euler connector */
+&spdif {
+ status = "disabled";
+};
+
+/* On Exp and Euler connectors */
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+/* On Wifi/BT connector, with RTS/CTS */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "disabled";
+};
+
+/* On Pi-2 connector */
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+/* On Euler connector */
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
+};
+
+/* On Euler connector, RTS/CTS optional */
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins>;
+ status = "disabled";
+};
+
&usb_otg {
dr_mode = "host";
status = "okay";
--- /dev/null
+/*
+ * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * Based on sun50i-a64-pine64.dts, which is:
+ * Copyright (c) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64-sopine.dtsi"
+
+/ {
+ model = "SoPine with baseboard";
+ compatible = "pine64,sopine-baseboard", "pine64,sopine",
+ "allwinner,sun50i-a64";
+
+ aliases {
+ ethernet0 = &emac;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_vcc1v8: vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_dc1sw>;
+ status = "okay";
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_vcc1v8>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-phy";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-mipi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * Based on sun50i-a64-pine64.dts, which is:
+ * Copyright (c) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sun50i-a64.dtsi"
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_dcdc1>;
+ non-removable;
+ disable-wp;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp803.dtsi"
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1040000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+®_eldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vdd-1v8-lpddr";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+®_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
*/
#include <dt-bindings/clock/sun50i-a64-ccu.h>
+#include <dt-bindings/clock/sun8i-r-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset/sun50i-a64-ccu.h>
#address-cells = <1>;
#size-cells = <1>;
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+/*
+ * The pipeline mixer0-lcd0 depends on clock CLK_MIXER0 from DE2 CCU.
+ * However there is no support for this clock on A64 yet, so we depend
+ * on the upstream clocks here to keep them (and thus CLK_MIXER0) up.
+ */
+ simplefb_lcd: framebuffer-lcd {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "mixer0-lcd0";
+ clocks = <&ccu CLK_TCON0>,
+ <&ccu CLK_DE>, <&ccu CLK_BUS_DE>;
+ status = "disabled";
+ };
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
method = "smc";
};
+ sound_spdif {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "On-board SPDIF";
+
+ simple-audio-card,cpu {
+ sound-dai = <&spdif>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&spdif_out>;
+ };
+ };
+
+ spdif_out: spdif-out {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dit";
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13
#size-cells = <1>;
ranges;
+ syscon: syscon@1c00000 {
+ compatible = "allwinner,sun50i-a64-system-controller",
+ "syscon";
+ reg = <0x01c00000 0x1000>;
+ };
+
+ dma: dma-controller@1c02000 {
+ compatible = "allwinner,sun50i-a64-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>;
+ dma-channels = <8>;
+ dma-requests = <27>;
+ resets = <&ccu RST_BUS_DMA>;
+ #dma-cells = <1>;
+ };
+
mmc0: mmc@1c0f000 {
compatible = "allwinner,sun50i-a64-mmc";
reg = <0x01c0f000 0x1000>;
#size-cells = <0>;
};
- usb_otg: usb@01c19000 {
+ usb_otg: usb@1c19000 {
compatible = "allwinner,sun8i-a33-musb";
reg = <0x01c19000 0x0400>;
clocks = <&ccu CLK_BUS_OTG>;
status = "disabled";
};
- usbphy: phy@01c19400 {
+ usbphy: phy@1c19400 {
compatible = "allwinner,sun50i-a64-usb-phy";
reg = <0x01c19400 0x14>,
<0x01c1a800 0x4>,
#phy-cells = <1>;
};
- ehci0: usb@01c1a000 {
+ ehci0: usb@1c1a000 {
compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
reg = <0x01c1a000 0x100>;
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- ohci0: usb@01c1a400 {
+ ohci0: usb@1c1a400 {
compatible = "allwinner,sun50i-a64-ohci", "generic-ohci";
reg = <0x01c1a400 0x100>;
interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- ehci1: usb@01c1b000 {
+ ehci1: usb@1c1b000 {
compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
reg = <0x01c1b000 0x100>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- ohci1: usb@01c1b400 {
+ ohci1: usb@1c1b400 {
compatible = "allwinner,sun50i-a64-ohci", "generic-ohci";
reg = <0x01c1b400 0x100>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
- ccu: clock@01c20000 {
+ ccu: clock@1c20000 {
compatible = "allwinner,sun50i-a64-ccu";
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
interrupt-controller;
#interrupt-cells = <3>;
+ i2c0_pins: i2c0_pins {
+ pins = "PH0", "PH1";
+ function = "i2c0";
+ };
+
i2c1_pins: i2c1_pins {
pins = "PH2", "PH3";
function = "i2c1";
bias-pull-up;
};
- uart0_pins_a: uart0@0 {
+ rmii_pins: rmii_pins {
+ pins = "PD10", "PD11", "PD13", "PD14", "PD17",
+ "PD18", "PD19", "PD20", "PD22", "PD23";
+ function = "emac";
+ drive-strength = <40>;
+ };
+
+ rgmii_pins: rgmii_pins {
+ pins = "PD8", "PD9", "PD10", "PD11", "PD12",
+ "PD13", "PD15", "PD16", "PD17", "PD18",
+ "PD19", "PD20", "PD21", "PD22", "PD23";
+ function = "emac";
+ drive-strength = <40>;
+ };
+
+ spdif_tx_pin: spdif {
+ pins = "PH8";
+ function = "spdif";
+ };
+
+ spi0_pins: spi0 {
+ pins = "PC0", "PC1", "PC2", "PC3";
+ function = "spi0";
+ };
+
+ spi1_pins: spi1 {
+ pins = "PD0", "PD1", "PD2", "PD3";
+ function = "spi1";
+ };
+
+ uart0_pins_a: uart0 {
pins = "PB8", "PB9";
function = "uart0";
};
pins = "PG8", "PG9";
function = "uart1";
};
+
+ uart2_pins: uart2-pins {
+ pins = "PB0", "PB1";
+ function = "uart2";
+ };
+
+ uart3_pins: uart3-pins {
+ pins = "PD0", "PD1";
+ function = "uart3";
+ };
+
+ uart4_pins: uart4-pins {
+ pins = "PD2", "PD3";
+ function = "uart4";
+ };
+
+ uart4_rts_cts_pins: uart4-rts-cts-pins {
+ pins = "PD4", "PD5";
+ function = "uart4";
+ };
+ };
+
+ spdif: spdif@1c21000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun50i-a64-spdif",
+ "allwinner,sun8i-h3-spdif";
+ reg = <0x01c21000 0x400>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
+ resets = <&ccu RST_BUS_SPDIF>;
+ clock-names = "apb", "spdif";
+ dmas = <&dma 2>;
+ dma-names = "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spdif_tx_pin>;
+ status = "disabled";
+ };
+
+ i2s0: i2s@1c22000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun50i-a64-i2s",
+ "allwinner,sun8i-h3-i2s";
+ reg = <0x01c22000 0x400>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S0>, <&ccu CLK_I2S0>;
+ clock-names = "apb", "mod";
+ resets = <&ccu RST_BUS_I2S0>;
+ dma-names = "rx", "tx";
+ dmas = <&dma 3>, <&dma 3>;
+ status = "disabled";
+ };
+
+ i2s1: i2s@1c22400 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun50i-a64-i2s",
+ "allwinner,sun8i-h3-i2s";
+ reg = <0x01c22400 0x400>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>;
+ clock-names = "apb", "mod";
+ resets = <&ccu RST_BUS_I2S1>;
+ dma-names = "rx", "tx";
+ dmas = <&dma 4>, <&dma 4>;
+ status = "disabled";
};
- pwm: pwm@01c21400 {
+ pwm: pwm@1c21400 {
compatible = "allwinner,sun50i-a64-pwm",
"allwinner,sun5i-a13-pwm";
reg = <0x01c21400 0x8>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&ccu 67>;
- resets = <&ccu 46>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
status = "disabled";
};
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&ccu 68>;
- resets = <&ccu 47>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
status = "disabled";
};
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&ccu 69>;
- resets = <&ccu 48>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
status = "disabled";
};
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&ccu 70>;
- resets = <&ccu 49>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
status = "disabled";
};
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&ccu 71>;
- resets = <&ccu 50>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
status = "disabled";
};
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu 63>;
- resets = <&ccu 42>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu 64>;
- resets = <&ccu 43>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b400 0x400>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu 65>;
- resets = <&ccu 44>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+
+ spi0: spi@1c68000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c68000 0x1000>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 23>, <&dma 23>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ resets = <&ccu RST_BUS_SPI0>;
+ status = "disabled";
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@1c69000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c69000 0x1000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 24>, <&dma 24>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ resets = <&ccu RST_BUS_SPI1>;
+ status = "disabled";
+ num-cs = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ emac: ethernet@1c30000 {
+ compatible = "allwinner,sun50i-a64-emac";
+ syscon = <&syscon>;
+ reg = <0x01c30000 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
+
+ mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
gic: interrupt-controller@1c81000 {
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
};
+ r_intc: interrupt-controller@1f00c00 {
+ compatible = "allwinner,sun50i-a64-r-intc",
+ "allwinner,sun6i-a31-r-intc";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x01f00c00 0x400>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
r_ccu: clock@1f01400 {
compatible = "allwinner,sun50i-a64-r-ccu";
reg = <0x01f01400 0x100>;
- clocks = <&osc24M>, <&osc32k>, <&iosc>;
- clock-names = "hosc", "losc", "iosc";
+ clocks = <&osc24M>, <&osc32k>, <&iosc>,
+ <&ccu 11>;
+ clock-names = "hosc", "losc", "iosc", "pll-periph";
#clock-cells = <1>;
#reset-cells = <1>;
};
- r_pio: pinctrl@01f02c00 {
+ r_pio: pinctrl@1f02c00 {
compatible = "allwinner,sun50i-a64-r-pinctrl";
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&r_ccu 3>, <&osc24M>, <&osc32k>;
+ clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&osc32k>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
#interrupt-cells = <3>;
+
+ r_rsb_pins: rsb {
+ pins = "PL0", "PL1";
+ function = "s_rsb";
+ };
+ };
+
+ r_rsb: rsb@1f03400 {
+ compatible = "allwinner,sun8i-a23-rsb";
+ reg = <0x01f03400 0x400>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu 6>;
+ clock-frequency = <3000000>;
+ resets = <&r_ccu 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_rsb_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ wdt0: watchdog@1c20ca0 {
+ compatible = "allwinner,sun50i-a64-wdt",
+ "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
};
};
};
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
- * Copyright (C) 2018 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2018 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
*/
/dts-v1/;
#include "sun50i-h5.dtsi"
-#include "sunxi-libretech-all-h3-cc.dtsi"
+#include <sunxi-libretech-all-h3-cc.dtsi>
/ {
model = "Libre Computer Board ALL-H3-CC H5";
/*
* Copyright (C) 2017 Antony Antony <antony@phenome.org>
- * Copyright (c) 2016 ARM Ltd.
+ * Copyright (C) 2016 ARM Ltd.
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
- * a) This library is free software; you can redistribute it and/or
+ * a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
- * This library is distributed in the hope that it will be useful,
+ * This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
/dts-v1/;
-
#include "sun50i-h5.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
- model = "FriendlyARM NanoPi NEO Plus 2";
+ model = "FriendlyARM NanoPi NEO Plus2";
compatible = "friendlyarm,nanopi-neo-plus2", "allwinner,sun50i-h5";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
stdout-path = "serial0:115200n8";
};
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "nanopi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status {
+ label = "nanopi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
reg_vcc3v3: vcc3v3 {
compatible = "regulator-fixed";
regulator-name = "vcc3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
+
+ vdd_cpux: gpio-regulator {
+ compatible = "regulator-gpio";
+ pinctrl-names = "default";
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0x1>;
+ states = <1100000 0x0
+ 1300000 0x1>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ post-power-on-delay-ms = <200>;
+ };
};
-&ehci1 {
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
status = "okay";
};
-&mmc0 {
+&ehci0 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&emac {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@7 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
+
+&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
status = "okay";
};
-&ohci1 {
+&ohci0 {
+ status = "okay";
+};
+
+&ohci3 {
status = "okay";
};
status = "okay";
};
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
&usbphy {
+ /* USB Type-A ports' VBUS is always on */
status = "okay";
};
/*
* Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
- * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
- * a) This library is free software; you can redistribute it and/or
+ * a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
- * This library is distributed in the hope that it will be useful,
+ * This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
/dts-v1/;
-
#include "sun50i-h5.dtsi"
#include <dt-bindings/gpio/gpio.h>
compatible = "friendlyarm,nanopi-neo2", "allwinner,sun50i-h5";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
stdout-path = "serial0:115200n8";
};
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "nanopi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status {
+ label = "nanopi:blue:status";
+ gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
reg_vcc3v3: vcc3v3 {
compatible = "regulator-fixed";
regulator-name = "vcc3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
+
+ reg_usb0_vbus: usb0-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+ };
};
-&mmc0 {
- compatible = "allwinner,sun50i-h5-mmc",
- "allwinner,sun50i-a64-mmc",
- "allwinner,sun5i-a13-mmc";
+&ehci0 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&emac {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@7 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
+
+&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
+&ohci0 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ /* USB Type-A port's VBUS is always on */
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ status = "okay";
+};
/*
- * Copyright (c) 2016 ARM Ltd.
+ * Copyright (C) 2016 ARM Ltd.
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
- * a) This library is free software; you can redistribute it and/or
+ * a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
- * This library is distributed in the hope that it will be useful,
+ * This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
/dts-v1/;
-
#include "sun50i-h5.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
- model = "OrangePi PC 2";
- compatible = "xunlong,orangepi-pc-2", "allwinner,sun50i-h5";
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
aliases {
- serial0 = &uart0;
ethernet0 = &emac;
+ serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
- memory {
- reg = <0x40000000 0x40000000>;
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
};
- soc {
- reg_vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ r-gpio-keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
};
};
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb0_vbus: usb0-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&de {
+ status = "okay";
};
&ehci0 {
status = "okay";
};
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
&emac {
pinctrl-names = "default";
pinctrl-0 = <&emac_rgmii_pins>;
- phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
status = "okay";
};
};
};
-&mmc0 {
- compatible = "allwinner,sun50i-h5-mmc",
- "allwinner,sun50i-a64-mmc",
- "allwinner,sun5i-a13-mmc";
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&ir {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
status = "okay";
};
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usbphy {
+ /* USB Type-A ports' VBUS is always on */
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_vbus-supply = <®_usb0_vbus>;
status = "okay";
};
/*
- * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * Based on sun50i-h5-orangepi-pc2.dts, which is:
+ * Copyright (C) 2016 ARM Ltd.
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
- * a) This library is free software; you can redistribute it and/or
+ * a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
- * This library is distributed in the hope that it will be useful,
+ * This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
/dts-v1/;
-
#include "sun50i-h5.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
/ {
- model = "OrangePi Prime";
+ model = "Xunlong Orange Pi Prime";
compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
stdout-path = "serial0:115200n8";
};
- memory {
- reg = <0x40000000 0x80000000>;
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
};
- soc {
- reg_vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ leds {
+ compatible = "gpio-leds";
+
+ pwr {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
};
+
+ status {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r-gpio-keys {
+ compatible = "gpio-keys";
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_usb0_vbus: usb0-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb0-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 2 14 GPIO_ACTIVE_LOW>; /* PC14 */
+ };
+};
+
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&de {
+ status = "okay";
};
&ehci0 {
status = "okay";
};
-&mmc0 {
- compatible = "allwinner,sun50i-h5-mmc",
- "allwinner,sun50i-a64-mmc",
- "allwinner,sun5i-a13-mmc";
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&ir {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
status = "okay";
};
status = "okay";
};
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usbphy {
+ /* USB Type-A ports' VBUS is always on */
+ usb0_id_det-gpios = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */
+ usb0_vbus-supply = <®_usb0_vbus>;
status = "okay";
};
#include <dt-bindings/gpio/gpio.h>
-
/ {
model = "OrangePi Zero Plus2";
compatible = "xunlong,orangepi-zero-plus2", "allwinner,sun50i-h5";
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
reg_vcc3v3: vcc3v3 {
compatible = "regulator-fixed";
regulator-name = "vcc3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
};
&mmc0 {
- compatible = "allwinner,sun50i-h5-mmc",
- "allwinner,sun50i-a64-mmc",
- "allwinner,sun5i-a13-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */
+ interrupt-names = "host-wake";
+ };
};
&mmc2 {
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
+};
/*
- * Copyright (c) 2016 ARM Ltd.
+ * Copyright (C) 2016 ARM Ltd.
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
- * a) This library is free software; you can redistribute it and/or
+ * a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
- * This library is distributed in the hope that it will be useful,
+ * This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "sun8i-h3.dtsi"
+#include <sunxi-h3-h5.dtsi>
/ {
cpus {
- cpu@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
enable-method = "psci";
};
+
cpu@1 {
compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
enable-method = "psci";
};
+
cpu@2 {
compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
enable-method = "psci";
};
+
cpu@3 {
compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
enable-method = "psci";
};
};
timer {
compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
};
compatible = "allwinner,sun50i-h5-ccu";
};
-&gic {
- compatible = "arm,gic-400";
+&display_clocks {
+ compatible = "allwinner,sun50i-h5-de2-clk";
};
&mmc0 {
&pio {
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
compatible = "allwinner,sun50i-h5-pinctrl";
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi Zero";
aliases {
serial0 = &uart0;
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet0 = &emac;
ethernet1 = &xr819;
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <200>;
};
};
+&ehci0 {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <®_vcc_wifi>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
};
};
+&ohci0 {
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
+&spi0 {
+ /* Disable SPI NOR by default: it optional on Orange Pi Zero boards */
+ status = "disabled";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
&usbphy {
- /* USB VBUS is always on */
+ /*
+ * USB Type-A port VBUS is always on. However, MicroUSB VBUS can only
+ * power up the board; when it's used as OTG port, this VBUS is
+ * always off even if the board is powered via GPIO pins.
+ */
status = "okay";
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Banana Pi BPI-M2-Plus";
compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
serial1 = &uart1;
};
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
- pinctrl-0 = <&pwr_led_bpi_m2p>;
pwr_led {
label = "bananapi-m2-plus:red:pwr";
gpio_keys {
compatible = "gpio-keys";
pinctrl-names = "default";
- pinctrl-0 = <&sw_r_bpi_m2p>;
sw4 {
label = "power";
};
};
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
pinctrl-names = "default";
- pinctrl-0 = <&wifi_en_bpi_m2p>;
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
};
};
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <®_vcc3v3>;
vqmmc-supply = <®_vcc3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
non-removable;
status = "okay";
- brcmf: bcrmf@1 {
+ brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&pio>;
status = "okay";
};
-&r_pio {
- pwr_led_bpi_m2p: led_pins@0 {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- sw_r_bpi_m2p: key_pins@0 {
- allwinner,pins = "PL3";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- wifi_en_bpi_m2p: wifi_en_pin {
- allwinner,pins = "PL7";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
+®_usb0_vbus {
+ gpio = <&pio 3 11 GPIO_ACTIVE_HIGH>; /* PD11 */
+ status = "okay";
};
&uart0 {
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_a>;
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
status = "okay";
};
};
&usbphy {
- /* USB VBUS is on as long as VCC-IO is on */
+ usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ /* USB host VBUS is on as long as VCC-IO is on */
status = "okay";
};
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
*/
/dts-v1/;
/ {
model = "FriendlyArm NanoPi M1 Plus";
compatible = "friendlyarm,nanopi-m1-plus", "allwinner,sun8i-h3";
+
+ aliases {
+ serial1 = &uart3;
+ ethernet0 = &emac;
+ ethernet1 = &sdio_wifi;
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
};
&ehci1 {
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii";
+
+ status = "okay";
+};
+
+&external_mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ sdio_wifi: sdio_wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
&ohci2 {
status = "okay";
};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>;
+ status = "okay";
+};
/ {
model = "FriendlyArm NanoPi M1";
compatible = "friendlyarm,nanopi-m1", "allwinner,sun8i-h3";
+
+ aliases {
+ ethernet0 = &emac;
+ };
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+};
+
+&de {
+ status = "okay";
};
&ehci1 {
status = "okay";
};
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "FriendlyARM NanoPi NEO Air";
gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
};
};
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
status = "okay";
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
};
&uart0 {
compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
};
+&ehci0 {
+ status = "okay";
+};
+
&emac {
phy-handle = <&int_mii_phy>;
phy-mode = "mii";
allwinner,leds-active-low;
status = "okay";
};
+
+&ohci0 {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+};
pinctrl-names = "default";
pinctrl-0 = <&sw_r_npi>;
- k1@0 {
+ k1 {
label = "k1";
linux,code = <KEY_POWER>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
&mmc0 {
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
status = "okay";
vmmc-supply = <®_vcc3v3>;
};
};
&pio {
- leds_npi: led_pins@0 {
+ leds_npi: led_pins {
pins = "PA10";
function = "gpio_out";
};
};
&r_pio {
- leds_r_npi: led_pins@0 {
+ leds_r_npi: led_pins {
pins = "PL10";
function = "gpio_out";
};
- sw_r_npi: key_pins@0 {
+ sw_r_npi: key_pins {
pins = "PL3";
function = "gpio_in";
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi 2";
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
};
};
+&codec {
+ allwinner,pa-gpios = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */
+ allwinner,audio-routing =
+ "Speaker", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <®_vcc3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
};
&pio {
- leds_opc: led_pins@0 {
- allwinner,pins = "PA15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_opc: led_pins {
+ pins = "PA15";
+ function = "gpio_out";
};
};
&r_pio {
- leds_r_opc: led_pins@0 {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_r_opc: led_pins {
+ pins = "PL10";
+ function = "gpio_out";
};
- sw_r_opc: key_pins@0 {
- allwinner,pins = "PL3", "PL4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ sw_r_opc: key_pins {
+ pins = "PL3", "PL4";
+ function = "gpio_in";
};
- wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin@0 {
- allwinner,pins = "PL7";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin {
+ pins = "PL7";
+ function = "gpio_out";
};
};
status = "okay";
};
-&usb1_vbus_pin_a {
- allwinner,pins = "PG13";
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
};
&usbphy {
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi Lite";
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
};
};
+&de {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
non-removable;
};
&pio {
- leds_opc: led_pins@0 {
- allwinner,pins = "PA15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_opc: led_pins {
+ pins = "PA15";
+ function = "gpio_out";
};
};
&r_pio {
- leds_r_opc: led_pins@0 {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_r_opc: led_pins {
+ pins = "PL10";
+ function = "gpio_out";
};
- sw_r_opc: key_pins@0 {
- allwinner,pins = "PL3";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ sw_r_opc: key_pins {
+ pins = "PL3";
+ function = "gpio_in";
};
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi One";
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
};
};
+
+ reg_vdd_cpux: vdd-cpux-regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ enable-active-high;
+ gpios-states = <0x1>;
+ states = <1100000 0x0
+ 1300000 0x1>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
};
&ehci1 {
status = "okay";
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&ohci0 {
status = "okay";
};
};
&pio {
- leds_opc: led_pins@0 {
- allwinner,pins = "PA15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_opc: led_pins {
+ pins = "PA15";
+ function = "gpio_out";
};
};
&r_pio {
- leds_r_opc: led_pins@0 {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_r_opc: led_pins {
+ pins = "PL10";
+ function = "gpio_out";
};
- sw_r_opc: key_pins@0 {
- allwinner,pins = "PL3";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ sw_r_opc: key_pins {
+ pins = "PL3";
+ function = "gpio_in";
};
};
+®_usb0_vbus {
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
- /* USB VBUS is always on */
+ /* USB Type-A port's VBUS is always on */
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_vbus-supply = <®_usb0_vbus>;
status = "okay";
};
};
};
+&emac {
+ /* LEDs changed to active high on the plus */
+ /delete-property/ allwinner,leds-active-low;
+};
+
&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
non-removable;
&mmc2_8bit_pins {
/* Increase drive strength for DDR modes */
- allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ drive-strength = <40>;
/* eMMC is missing pull-ups */
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ bias-pull-up;
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi PC";
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
};
};
+&codec {
+ allwinner,audio-routing =
+ "Line Out", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpux>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
status = "okay";
};
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&ohci0 {
status = "okay";
};
};
&pio {
- leds_opc: led_pins@0 {
- allwinner,pins = "PA15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_opc: led_pins {
+ pins = "PA15";
+ function = "gpio_out";
+ };
+};
+
+&r_i2c {
+ status = "okay";
+
+ reg_vdd_cpux: regulator@65 {
+ compatible = "silergy,sy8106a";
+ reg = <0x65>;
+ regulator-name = "vdd-cpux";
+ silergy,fixed-microvolt = <1200000>;
+ /*
+ * The datasheet uses 1.1V as the minimum value of VDD-CPUX,
+ * however both the Armbian DVFS table and the official one
+ * have operating points with voltage under 1.1V, and both
+ * DVFS table are known to work properly at the lowest
+ * operating point.
+ *
+ * Use 1.0V as the minimum voltage instead.
+ */
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
};
};
&r_pio {
- leds_r_opc: led_pins@0 {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_r_opc: led_pins {
+ pins = "PL10";
+ function = "gpio_out";
};
- sw_r_opc: key_pins@0 {
- allwinner,pins = "PL3";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ sw_r_opc: key_pins {
+ pins = "PL3";
+ function = "gpio_in";
};
};
+®_usb0_vbus {
+ gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
-&usbphy {
- /* USB VBUS is always on */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "otg";
status = "okay";
};
-&emac {
- phy-handle = <&int_mii_phy>;
- phy-mode = "mii";
- allwinner,leds-active-low;
+&usbphy {
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ usb0_vbus-supply = <®_usb0_vbus>;
+ /* VBUS on USB host ports are always on */
status = "okay";
};
model = "Xunlong Orange Pi Plus / Plus 2";
compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+ aliases {
+ ethernet0 = &emac;
+ };
+
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_orangepi>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
&emac {
- /* The Orange Pi Plus uses an external phy */
pinctrl-names = "default";
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <®_gmac_3v3>;
+ phy-handle = <&ext_rgmii_phy>;
phy-mode = "rgmii";
+
+ status = "okay";
};
&external_mdio {
&mmc2_8bit_pins {
/* Increase drive strength for DDR modes */
- allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ drive-strength = <40>;
/* eMMC is missing pull-ups */
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ bias-pull-up;
};
&pio {
- gmac_power_pin_orangepi: gmac_power_pin@0 {
- allwinner,pins = "PD6";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb3_vbus_pin_a: usb3_vbus_pin@0 {
- allwinner,pins = "PG11";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ usb3_vbus_pin_a: usb3_vbus_pin {
+ pins = "PG11";
+ function = "gpio_out";
};
};
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_orangepi>;
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
startup-delay-us = <100000>;
enable-active-high;
- gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
};
};
&emac {
- /* The Orange Pi Plus 2E uses an external gbit phy */
pinctrl-names = "default";
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <®_gmac_3v3>;
phy-handle = <&ext_rgmii_phy>;
phy-mode = "rgmii";
+ status = "okay";
};
&external_mdio {
reg = <1>;
};
};
-
-&pio {
- gmac_power_pin_orangepi: gmac_power_pin@0 {
- allwinner,pins = "PD6";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
-#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include "sunxi-h3-h5.dtsi"
/ {
- interrupt-parent = <&gic>;
+ cpu0_opp_table: opp_table0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp@648000000 {
+ opp-hz = /bits/ 64 <648000000>;
+ opp-microvolt = <1040000 1040000 1300000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
- aliases {
- ethernet0 = &emac;
+ opp@816000000 {
+ opp-hz = /bits/ 64 <816000000>;
+ opp-microvolt = <1100000 1100000 1300000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp@1008000000 {
+ opp-hz = /bits/ 64 <1008000000>;
+ opp-microvolt = <1200000 1200000 1300000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
- cpu@0 {
+ cpu0: cpu@0 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <0>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
+ operating-points-v2 = <&cpu0_opp_table>;
+ #cooling-cells = <2>;
};
cpu@1 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <1>;
+ operating-points-v2 = <&cpu0_opp_table>;
};
cpu@2 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <2>;
+ operating-points-v2 = <&cpu0_opp_table>;
};
cpu@3 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <3>;
+ operating-points-v2 = <&cpu0_opp_table>;
};
};
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk@01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk@01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- syscon: syscon@1c00000 {
- compatible = "allwinner,sun8i-h3-system-controller",
- "syscon";
- reg = <0x01c00000 0x1000>;
- };
-
- dma: dma-controller@01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun7i-a20-mmc",
- "allwinner,sun5i-a13-mmc";
- reg = <0x01c0f000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC0>,
- <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc1: mmc@01c10000 {
- compatible = "allwinner,sun7i-a20-mmc",
- "allwinner,sun5i-a13-mmc";
- reg = <0x01c10000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC1>,
- <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc2: mmc@01c11000 {
- compatible = "allwinner,sun7i-a20-mmc",
- "allwinner,sun5i-a13-mmc";
- reg = <0x01c11000 0x1000>;
- clocks = <&ccu CLK_BUS_MMC2>,
- <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usb_otg: usb@1c19000 {
- compatible = "allwinner,sun8i-h3-musb";
- reg = <0x01c19000 0x400>;
- clocks = <&ccu CLK_BUS_OTG>;
- resets = <&ccu RST_BUS_OTG>;
- interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "mc";
- phys = <&usbphy 0>;
- phy-names = "usb";
- extcon = <&usbphy 0>;
- status = "disabled";
- };
-
- usbphy: phy@01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
- };
-
- ehci0: usb@1c1a000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1a000 0x100>;
- interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>;
- resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
- status = "disabled";
- };
-
- ohci0: usb@1c1a400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1a400 0x100>;
- interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>,
- <&ccu CLK_USB_OHCI0>;
- resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
- status = "disabled";
- };
-
- ehci1: usb@01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci1: usb@01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb@01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb@01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb@01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb@01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock@01c20000 {
- compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- pio: pinctrl@01c20800 {
- compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- emac_rgmii_pins: emac0 {
- pins = "PD0", "PD1", "PD2", "PD3", "PD4",
- "PD5", "PD7", "PD8", "PD9", "PD10",
- "PD12", "PD13", "PD15", "PD16", "PD17";
- function = "emac";
- drive-strength = <40>;
- };
-
- mmc0_pins_a: mmc0@0 {
- allwinner,pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- allwinner,function = "mmc0";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_cd_pin: mmc0_cd_pin@0 {
- allwinner,pins = "PF6";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- mmc1_pins_a: mmc1@0 {
- allwinner,pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- allwinner,function = "mmc1";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- allwinner,pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- allwinner,function = "mmc2";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- uart0_pins_a: uart0@0 {
- allwinner,pins = "PA4", "PA5";
- allwinner,function = "uart0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- uart1_pins_a: uart1@0 {
- allwinner,pins = "PG6", "PG7", "PG8", "PG9";
- allwinner,function = "uart1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
- };
-
- timer@01c20c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x01c20c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- wdt0: watchdog@01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- uart0: serial@01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial@01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial@01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial@01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- emac: ethernet@1c30000 {
- compatible = "allwinner,sun8i-h3-emac";
- syscon = <&syscon>;
- reg = <0x01c30000 0x10000>;
- interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "macirq";
- resets = <&ccu RST_BUS_EMAC>;
- reset-names = "stmmaceth";
- clocks = <&ccu CLK_BUS_EMAC>;
- clock-names = "stmmaceth";
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
-
- mdio: mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
- };
-
- mdio-mux {
- compatible = "allwinner,sun8i-h3-mdio-mux";
- #address-cells = <1>;
- #size-cells = <0>;
-
- mdio-parent-bus = <&mdio>;
- /* Only one MDIO is usable at the time */
- internal_mdio: mdio@1 {
- compatible = "allwinner,sun8i-h3-mdio-internal";
- reg = <1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- int_mii_phy: ethernet-phy@1 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <1>;
- clocks = <&ccu CLK_BUS_EPHY>;
- resets = <&ccu RST_BUS_EPHY>;
- };
- };
-
- external_mdio: mdio@2 {
- reg = <2>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
- };
+ mali: gpu@1c40000 {
+ compatible = "allwinner,sun8i-h3-mali", "arm,mali-400";
+ reg = <0x01c40000 0x10000>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gp",
+ "gpmmu",
+ "pp0",
+ "ppmmu0",
+ "pp1",
+ "ppmmu1",
+ "pmu";
+ clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
+ clock-names = "bus", "core";
+ resets = <&ccu RST_BUS_GPU>;
+
+ assigned-clocks = <&ccu CLK_GPU>;
+ assigned-clock-rates = <384000000>;
};
+ };
+};
- gic: interrupt-controller@01c81000 {
- compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
- reg = <0x01c81000 0x1000>,
- <0x01c82000 0x1000>,
- <0x01c84000 0x2000>,
- <0x01c86000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
+&ccu {
+ compatible = "allwinner,sun8i-h3-ccu";
+};
- rtc: rtc@01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
+&display_clocks {
+ compatible = "allwinner,sun8i-h3-de2-clk";
+};
- apb0_reset: reset@01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
+&mmc0 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
- ir: ir@01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
+&mmc1 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
- r_pio: pinctrl@01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>;
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
+&mmc2 {
+ compatible = "allwinner,sun7i-a20-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+};
- ir_pins_a: ir@0 {
- allwinner,pins = "PL11";
- allwinner,function = "s_cir_rx";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
- };
- };
+&pio {
+ compatible = "allwinner,sun8i-h3-pinctrl";
};
compatible = "sinovoip,bpi-m2-ultra", "allwinner,sun8i-r40";
aliases {
+ ethernet0 = &gmac;
serial0 = &uart0;
};
pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_rgmii_pins>;
+ phy-handle = <&phy1>;
+ phy-mode = "rgmii";
+ status = "okay";
+};
+
+&gmac_mdio {
+ phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
#interrupt-cells = <3>;
#gpio-cells = <3>;
+ gmac_rgmii_pins: gmac-rgmii-pins {
+ pins = "PA0", "PA1", "PA2", "PA3",
+ "PA4", "PA5", "PA6", "PA7",
+ "PA8", "PA10", "PA11", "PA12",
+ "PA13", "PA15", "PA16";
+ function = "gmac";
+ /*
+ * data lines in RGMII mode use DDR mode
+ * and need a higher signal drive strength
+ */
+ drive-strength = <40>;
+ };
+
i2c0_pins: i2c0_pins {
pins = "PB0", "PB1";
function = "i2c0";
#size-cells = <0>;
};
+ gmac: ethernet@1c50000 {
+ compatible = "allwinner,sun8i-r40-gmac";
+ syscon = <&ccu>;
+ reg = <0x01c50000 0x10000>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_GMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_GMAC>;
+ clock-names = "stmmaceth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ gmac_mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
gic: interrupt-controller@1c81000 {
compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
reg = <0x01c81000 0x1000>,
--- /dev/null
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/clock/sun8i-de2.h>
+#include <dt-bindings/clock/sun8i-h3-ccu.h>
+#include <dt-bindings/clock/sun8i-r-ccu.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/sun8i-de2.h>
+#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include <dt-bindings/reset/sun8i-r-ccu.h>
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ chosen {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ framebuffer-hdmi {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "mixer0-lcd0-hdmi";
+ clocks = <&display_clocks CLK_MIXER0>,
+ <&ccu CLK_TCON0>, <&ccu CLK_HDMI>;
+ status = "disabled";
+ };
+
+ framebuffer-tve {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "mixer1-lcd1-tve";
+ clocks = <&display_clocks CLK_MIXER1>,
+ <&ccu CLK_TVE>;
+ status = "disabled";
+ };
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ iosc: internal-osc-clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <16000000>;
+ clock-accuracy = <300000000>;
+ clock-output-names = "iosc";
+ };
+ };
+
+ de: display-engine {
+ compatible = "allwinner,sun8i-h3-display-engine";
+ allwinner,pipelines = <&mixer0>;
+ status = "disabled";
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ display_clocks: clock@1000000 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01000000 0x100000>;
+ clocks = <&ccu CLK_DE>,
+ <&ccu CLK_BUS_DE>;
+ clock-names = "mod",
+ "bus";
+ resets = <&ccu RST_BUS_DE>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ mixer0: mixer@1100000 {
+ compatible = "allwinner,sun8i-h3-de2-mixer-0";
+ reg = <0x01100000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER0>,
+ <&display_clocks CLK_MIXER0>;
+ clock-names = "bus",
+ "mod";
+ resets = <&display_clocks RST_MIXER0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer0_out: port@1 {
+ reg = <1>;
+
+ mixer0_out_tcon0: endpoint {
+ remote-endpoint = <&tcon0_in_mixer0>;
+ };
+ };
+ };
+ };
+
+ syscon: syscon@1c00000 {
+ compatible = "allwinner,sun8i-h3-system-controller",
+ "syscon";
+ reg = <0x01c00000 0x1000>;
+ };
+
+ dma: dma-controller@1c02000 {
+ compatible = "allwinner,sun8i-h3-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>;
+ resets = <&ccu RST_BUS_DMA>;
+ #dma-cells = <1>;
+ };
+
+ tcon0: lcd-controller@1c0c000 {
+ compatible = "allwinner,sun8i-h3-tcon-tv",
+ "allwinner,sun8i-a83t-tcon-tv";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
+ clock-names = "ahb", "tcon-ch1";
+ resets = <&ccu RST_BUS_TCON0>;
+ reset-names = "lcd";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ reg = <0>;
+
+ tcon0_in_mixer0: endpoint {
+ remote-endpoint = <&mixer0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ tcon0_out_hdmi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&hdmi_in_tcon0>;
+ };
+ };
+ };
+ };
+
+ mmc0: mmc@1c0f000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c0f000 0x1000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@1c10000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c10000 0x1000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@1c11000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c11000 0x1000>;
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usb_otg: usb@1c19000 {
+ compatible = "allwinner,sun8i-h3-musb";
+ reg = <0x01c19000 0x400>;
+ clocks = <&ccu CLK_BUS_OTG>;
+ resets = <&ccu RST_BUS_OTG>;
+ interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "mc";
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ extcon = <&usbphy 0>;
+ status = "disabled";
+ };
+
+ usbphy: phy@1c19400 {
+ compatible = "allwinner,sun8i-h3-usb-phy";
+ reg = <0x01c19400 0x2c>,
+ <0x01c1a800 0x4>,
+ <0x01c1b800 0x4>,
+ <0x01c1c800 0x4>,
+ <0x01c1d800 0x4>;
+ reg-names = "phy_ctrl",
+ "pmu0",
+ "pmu1",
+ "pmu2",
+ "pmu3";
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_PHY2>,
+ <&ccu CLK_USB_PHY3>;
+ clock-names = "usb0_phy",
+ "usb1_phy",
+ "usb2_phy",
+ "usb3_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>,
+ <&ccu RST_USB_PHY3>;
+ reset-names = "usb0_reset",
+ "usb1_reset",
+ "usb2_reset",
+ "usb3_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci0: usb@1c1a000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1a000 0x100>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>;
+ resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+ status = "disabled";
+ };
+
+ ohci0: usb@1c1a400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1a400 0x100>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+ status = "disabled";
+ };
+
+ ehci1: usb@1c1b000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1b000 0x100>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@1c1b400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1b400 0x100>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci2: usb@1c1c000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1c000 0x100>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci2: usb@1c1c400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1c400 0x100>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci3: usb@1c1d000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1d000 0x100>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci3: usb@1c1d400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1d400 0x100>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ccu: clock@1c20000 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ pio: pinctrl@1c20800 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ emac_rgmii_pins: emac0 {
+ pins = "PD0", "PD1", "PD2", "PD3", "PD4",
+ "PD5", "PD7", "PD8", "PD9", "PD10",
+ "PD12", "PD13", "PD15", "PD16", "PD17";
+ function = "emac";
+ drive-strength = <40>;
+ };
+
+ i2c0_pins: i2c0 {
+ pins = "PA11", "PA12";
+ function = "i2c0";
+ };
+
+ i2c1_pins: i2c1 {
+ pins = "PA18", "PA19";
+ function = "i2c1";
+ };
+
+ i2c2_pins: i2c2 {
+ pins = "PE12", "PE13";
+ function = "i2c2";
+ };
+
+ mmc0_pins: mmc0 {
+ pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc1_pins: mmc1 {
+ pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_8bit_pins: mmc2_8bit {
+ pins = "PC5", "PC6", "PC8",
+ "PC9", "PC10", "PC11",
+ "PC12", "PC13", "PC14",
+ "PC15", "PC16";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ spdif_tx_pins_a: spdif {
+ pins = "PA17";
+ function = "spdif";
+ };
+
+ spi0_pins: spi0 {
+ pins = "PC0", "PC1", "PC2", "PC3";
+ function = "spi0";
+ };
+
+ spi1_pins: spi1 {
+ pins = "PA15", "PA16", "PA14", "PA13";
+ function = "spi1";
+ };
+
+ uart0_pins_a: uart0 {
+ pins = "PA4", "PA5";
+ function = "uart0";
+ };
+
+ uart1_pins: uart1 {
+ pins = "PG6", "PG7";
+ function = "uart1";
+ };
+
+ uart1_rts_cts_pins: uart1_rts_cts {
+ pins = "PG8", "PG9";
+ function = "uart1";
+ };
+
+ uart2_pins: uart2 {
+ pins = "PA0", "PA1";
+ function = "uart2";
+ };
+
+ uart3_pins: uart3 {
+ pins = "PA13", "PA14";
+ function = "uart3";
+ };
+
+ uart3_rts_cts_pins: uart3_rts_cts {
+ pins = "PA15", "PA16";
+ function = "uart3";
+ };
+ };
+
+ timer@1c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ emac: ethernet@1c30000 {
+ compatible = "allwinner,sun8i-h3-emac";
+ syscon = <&syscon>;
+ reg = <0x01c30000 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC>;
+ clock-names = "stmmaceth";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ };
+
+ mdio-mux {
+ compatible = "allwinner,sun8i-h3-mdio-mux";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio-parent-bus = <&mdio>;
+ /* Only one MDIO is usable at the time */
+ internal_mdio: mdio@1 {
+ compatible = "allwinner,sun8i-h3-mdio-internal";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ int_mii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ clocks = <&ccu CLK_BUS_EPHY>;
+ resets = <&ccu RST_BUS_EPHY>;
+ };
+ };
+
+ external_mdio: mdio@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+ };
+
+ spi0: spi@1c68000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c68000 0x1000>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 23>, <&dma 23>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ resets = <&ccu RST_BUS_SPI0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@1c69000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c69000 0x1000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 24>, <&dma 24>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ resets = <&ccu RST_BUS_SPI1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ wdt0: watchdog@1c20ca0 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ spdif: spdif@1c21000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-h3-spdif";
+ reg = <0x01c21000 0x400>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
+ resets = <&ccu RST_BUS_SPDIF>;
+ clock-names = "apb", "spdif";
+ dmas = <&dma 2>;
+ dma-names = "tx";
+ status = "disabled";
+ };
+
+ pwm: pwm@1c21400 {
+ compatible = "allwinner,sun8i-h3-pwm";
+ reg = <0x01c21400 0x8>;
+ clocks = <&osc24M>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ i2s0: i2s@1c22000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-h3-i2s";
+ reg = <0x01c22000 0x400>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S0>, <&ccu CLK_I2S0>;
+ clock-names = "apb", "mod";
+ dmas = <&dma 3>, <&dma 3>;
+ resets = <&ccu RST_BUS_I2S0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2s1: i2s@1c22400 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-h3-i2s";
+ reg = <0x01c22400 0x400>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>;
+ clock-names = "apb", "mod";
+ dmas = <&dma 4>, <&dma 4>;
+ resets = <&ccu RST_BUS_I2S1>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ codec: codec@1c22c00 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun8i-h3-codec";
+ reg = <0x01c22c00 0x400>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
+ clock-names = "apb", "codec";
+ resets = <&ccu RST_BUS_CODEC>;
+ dmas = <&dma 15>, <&dma 15>;
+ dma-names = "rx", "tx";
+ allwinner,codec-analog-controls = <&codec_analog>;
+ status = "disabled";
+ };
+
+ uart0: serial@1c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ dmas = <&dma 6>, <&dma 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial@1c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ dmas = <&dma 7>, <&dma 7>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial@1c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ dmas = <&dma 8>, <&dma 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial@1c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ dmas = <&dma 9>, <&dma 9>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2c0: i2c@1c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@1c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@1c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ gic: interrupt-controller@1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ hdmi: hdmi@1ee0000 {
+ compatible = "allwinner,sun8i-h3-dw-hdmi",
+ "allwinner,sun8i-a83t-dw-hdmi";
+ reg = <0x01ee0000 0x10000>;
+ reg-io-width = <1>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
+ <&ccu CLK_HDMI>;
+ clock-names = "iahb", "isfr", "tmds";
+ resets = <&ccu RST_BUS_HDMI1>;
+ reset-names = "ctrl";
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi-phy";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdmi_in: port@0 {
+ reg = <0>;
+
+ hdmi_in_tcon0: endpoint {
+ remote-endpoint = <&tcon0_out_hdmi>;
+ };
+ };
+
+ hdmi_out: port@1 {
+ reg = <1>;
+ };
+ };
+ };
+
+ hdmi_phy: hdmi-phy@1ef0000 {
+ compatible = "allwinner,sun8i-h3-hdmi-phy";
+ reg = <0x01ef0000 0x10000>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
+ <&ccu 6>;
+ clock-names = "bus", "mod", "pll-0";
+ resets = <&ccu RST_BUS_HDMI0>;
+ reset-names = "phy";
+ #phy-cells = <0>;
+ };
+
+ rtc: rtc@1f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x54>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ r_ccu: clock@1f01400 {
+ compatible = "allwinner,sun8i-h3-r-ccu";
+ reg = <0x01f01400 0x100>;
+ clocks = <&osc24M>, <&osc32k>, <&iosc>,
+ <&ccu 9>;
+ clock-names = "hosc", "losc", "iosc", "pll-periph";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ codec_analog: codec-analog@1f015c0 {
+ compatible = "allwinner,sun8i-h3-codec-analog";
+ reg = <0x01f015c0 0x4>;
+ };
+
+ ir: ir@1f02000 {
+ compatible = "allwinner,sun5i-a13-ir";
+ clocks = <&r_ccu CLK_APB0_IR>, <&r_ccu CLK_IR>;
+ clock-names = "apb", "ir";
+ resets = <&r_ccu RST_APB0_IR>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x01f02000 0x40>;
+ status = "disabled";
+ };
+
+ r_i2c: i2c@1f02400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01f02400 0x400>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_i2c_pins>;
+ clocks = <&r_ccu CLK_APB0_I2C>;
+ resets = <&r_ccu RST_APB0_I2C>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ r_pio: pinctrl@1f02c00 {
+ compatible = "allwinner,sun8i-h3-r-pinctrl";
+ reg = <0x01f02c00 0x400>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ ir_pins_a: ir {
+ pins = "PL11";
+ function = "s_cir_rx";
+ };
+
+ r_i2c_pins: r-i2c {
+ pins = "PL0", "PL1";
+ function = "s_i2c";
+ };
+ };
+ };
+};
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <®_vcc_io>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
status = "okay";
};
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc_io>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
u32 reserved11;
u32 sata_clk_cfg; /* 0xc8 SATA clock control (R40 only) */
u32 usb_clk_cfg; /* 0xcc USB clock control */
- u32 gmac_clk_cfg; /* 0xd0 GMAC clock control */
+#ifdef CONFIG_MACH_SUN8I_R40
+ u32 cir0_clk_cfg; /* 0xd0 CIR0 clock control (R40 only) */
+#else
+ u32 gmac_clk_cfg; /* 0xd0 GMAC clock control (not for R40) */
+#endif
u32 reserved12[7];
u32 mdfs_clk_cfg; /* 0xf0 MDFS clock control */
u32 dram_clk_cfg; /* 0xf4 DRAM configuration clock control */
u32 mtc_clk_cfg; /* 0x158 MTC module clock */
u32 mbus0_clk_cfg; /* 0x15c MBUS0 module clock */
u32 mbus1_clk_cfg; /* 0x160 MBUS1 module clock */
+#ifdef CONFIG_MACH_SUN8I_R40
+ u32 gmac_clk_cfg; /* 0x164 GMAC clock control (R40 only) */
+#else
u32 reserved16;
+#endif
u32 mipi_dsi_clk_cfg; /* 0x168 MIPI DSI clock control */
u32 mipi_csi_clk_cfg; /* 0x16c MIPI CSI clock control */
u32 reserved17[4];
bool "sun4i (Allwinner A10)"
select CPU_V7A
select ARM_CORTEX_CPU_IS_UP
+ select DM_MMC if MMC
+ select DM_SCSI if SCSI
select PHY_SUN4I_USB
select DRAM_SUN4I
select SUNXI_GEN_SUN4I
# CONFIG_CMD_FLASH is not set
CONFIG_SCSI_AHCI=y
CONFIG_AXP_DLDO4_VOLT=2500
+CONFIG_AXP_ALDO2_VOLT=2500
CONFIG_AXP_ELDO3_VOLT=1200
CONFIG_SCSI=y
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
+CONFIG_SUN8I_EMAC=y
+CONFIG_RGMII=y
+CONFIG_MACPWR="PA17"
CONFIG_DRAM_CLK=672
CONFIG_DRAM_ZQ=3881979
CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_DEFAULT_DEVICE_TREE="sun8i-h2-plus-libretech-all-h3-cc"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DRAM_CLK=672
CONFIG_DRAM_ZQ=3881979
CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-libretech-all-h3-cc"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
# CONFIG_CMD_FLASH is not set
CONFIG_DRAM_CLK=672
CONFIG_DRAM_ZQ=3881979
CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-libretech-all-h3-cc"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
# CONFIG_CMD_FLASH is not set
CONFIG_MMC0_CD_PIN=""
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_SPL_SPI_SUNXI=y
-CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-pine64-plus"
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-sopine-baseboard"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_SPL_DOS_PARTITION is not set
}
static const struct udevice_id sunxi_mmc_ids[] = {
+ { .compatible = "allwinner,sun4i-a10-mmc" },
{ .compatible = "allwinner,sun5i-a13-mmc" },
+ { .compatible = "allwinner,sun7i-a20-mmc" },
{ }
};
#define AHB_GATE_OFFSET_EPHY 0
-#if defined(CONFIG_MACH_SUNXI_H3_H5)
-#define SUN8I_GPD8_GMAC 2
-#else
-#define SUN8I_GPD8_GMAC 4
-#endif
+/* IO mux settings */
+#define SUN8I_IOMUX_H3 2
+#define SUN8I_IOMUX_R40 5
+#define SUN8I_IOMUX 4
/* H3/A64 EMAC Register's offset */
#define EMAC_CTL0 0x00
A83T_EMAC = 1,
H3_EMAC,
A64_EMAC,
+ R40_GMAC,
};
struct emac_dma_desc {
reg = readl(priv->sysctl_reg + 0x30);
+ if (priv->variant == R40_GMAC)
+ return 0;
+
if (priv->variant == H3_EMAC) {
ret = sun8i_emac_set_syscon_ephy(priv, ®);
if (ret)
static int parse_phy_pins(struct udevice *dev)
{
+ struct emac_eth_dev *priv = dev_get_priv(dev);
int offset;
const char *pin_name;
int drive, pull = SUN4I_PINCTRL_NO_PULL, i;
if (pin < 0)
continue;
- sunxi_gpio_set_cfgpin(pin, SUN8I_GPD8_GMAC);
+ if (priv->variant == H3_EMAC)
+ sunxi_gpio_set_cfgpin(pin, SUN8I_IOMUX_H3);
+ else if (priv->variant == R40_GMAC)
+ sunxi_gpio_set_cfgpin(pin, SUN8I_IOMUX_R40);
+ else
+ sunxi_gpio_set_cfgpin(pin, SUN8I_IOMUX);
+
if (drive != ~0)
sunxi_gpio_set_drv(pin, drive);
if (pull != ~0)
{
struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
-#ifdef CONFIG_MACH_SUNXI_H3_H5
- /* Only H3/H5 have clock controls for internal EPHY */
- if (priv->use_internal_phy) {
- /* Set clock gating for ephy */
- setbits_le32(&ccm->bus_gate4, BIT(AHB_GATE_OFFSET_EPHY));
-
- /* Deassert EPHY */
- setbits_le32(&ccm->ahb_reset2_cfg, BIT(AHB_RESET_OFFSET_EPHY));
+ if (priv->variant == H3_EMAC) {
+ /* Only H3/H5 have clock controls for internal EPHY */
+ if (priv->use_internal_phy) {
+ /* Set clock gating for ephy */
+ setbits_le32(&ccm->bus_gate4,
+ BIT(AHB_GATE_OFFSET_EPHY));
+
+ /* Deassert EPHY */
+ setbits_le32(&ccm->ahb_reset2_cfg,
+ BIT(AHB_RESET_OFFSET_EPHY));
+ }
}
-#endif
-
- /* Set clock gating for emac */
- setbits_le32(&ccm->ahb_gate0, BIT(AHB_GATE_OFFSET_GMAC));
- /* De-assert EMAC */
- setbits_le32(&ccm->ahb_reset0_cfg, BIT(AHB_RESET_OFFSET_GMAC));
+ if (priv->variant == R40_GMAC) {
+ /* Set clock gating for emac */
+ setbits_le32(&ccm->ahb_reset1_cfg, BIT(AHB_RESET_OFFSET_GMAC));
+
+ /* De-assert EMAC */
+ setbits_le32(&ccm->ahb_gate1, BIT(AHB_GATE_OFFSET_GMAC));
+
+ /* Select RGMII for R40 */
+ setbits_le32(&ccm->gmac_clk_cfg,
+ CCM_GMAC_CTRL_TX_CLK_SRC_INT_RGMII |
+ CCM_GMAC_CTRL_GPIT_RGMII);
+ setbits_le32(&ccm->gmac_clk_cfg,
+ CCM_GMAC_CTRL_TX_CLK_DELAY(CONFIG_GMAC_TX_DELAY));
+ } else {
+ /* Set clock gating for emac */
+ setbits_le32(&ccm->ahb_gate0, BIT(AHB_GATE_OFFSET_GMAC));
+
+ /* De-assert EMAC */
+ setbits_le32(&ccm->ahb_reset0_cfg, BIT(AHB_RESET_OFFSET_GMAC));
+ }
}
#if defined(CONFIG_DM_GPIO)
return -EINVAL;
}
- offset = fdtdec_lookup_phandle(gd->fdt_blob, node, "syscon");
- if (offset < 0) {
- debug("%s: cannot find syscon node\n", __func__);
- return -EINVAL;
- }
- reg = fdt_getprop(gd->fdt_blob, offset, "reg", NULL);
- if (!reg) {
- debug("%s: cannot find reg property in syscon node\n",
- __func__);
+ priv->variant = dev_get_driver_data(dev);
+
+ if (!priv->variant) {
+ printf("%s: Missing variant\n", __func__);
return -EINVAL;
}
- priv->sysctl_reg = fdt_translate_address((void *)gd->fdt_blob,
- offset, reg);
- if (priv->sysctl_reg == FDT_ADDR_T_NONE) {
- debug("%s: Cannot find syscon base address\n", __func__);
- return -EINVAL;
+
+ if (priv->variant != R40_GMAC) {
+ offset = fdtdec_lookup_phandle(gd->fdt_blob, node, "syscon");
+ if (offset < 0) {
+ debug("%s: cannot find syscon node\n", __func__);
+ return -EINVAL;
+ }
+ reg = fdt_getprop(gd->fdt_blob, offset, "reg", NULL);
+ if (!reg) {
+ debug("%s: cannot find reg property in syscon node\n",
+ __func__);
+ return -EINVAL;
+ }
+ priv->sysctl_reg = fdt_translate_address((void *)gd->fdt_blob,
+ offset, reg);
+ if (priv->sysctl_reg == FDT_ADDR_T_NONE) {
+ debug("%s: Cannot find syscon base address\n",
+ __func__);
+ return -EINVAL;
+ }
}
pdata->phy_interface = -1;
return -EINVAL;
}
- priv->variant = dev_get_driver_data(dev);
-
- if (!priv->variant) {
- printf("%s: Missing variant '%s'\n", __func__,
- (char *)priv->variant);
- return -EINVAL;
- }
-
if (priv->variant == H3_EMAC) {
int parent = fdt_parent_offset(gd->fdt_blob, offset);
.data = (uintptr_t)A64_EMAC },
{.compatible = "allwinner,sun8i-a83t-emac",
.data = (uintptr_t)A83T_EMAC },
+ {.compatible = "allwinner,sun8i-r40-gmac",
+ .data = (uintptr_t)R40_GMAC },
{ }
};
--- /dev/null
+/*
+ * Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+#ifndef _DT_BINDINGS_CLOCK_SUN8I_DE2_H_
+#define _DT_BINDINGS_CLOCK_SUN8I_DE2_H_
+
+#define CLK_BUS_MIXER0 0
+#define CLK_BUS_MIXER1 1
+#define CLK_BUS_WB 2
+
+#define CLK_MIXER0 6
+#define CLK_MIXER1 7
+#define CLK_WB 8
+
+#endif /* _DT_BINDINGS_CLOCK_SUN8I_DE2_H_ */
--- /dev/null
+/*
+ * Copyright (c) 2016 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN8I_R_CCU_H_
+#define _DT_BINDINGS_CLK_SUN8I_R_CCU_H_
+
+#define CLK_AR100 0
+
+#define CLK_APB0_PIO 3
+#define CLK_APB0_IR 4
+#define CLK_APB0_TIMER 5
+#define CLK_APB0_RSB 6
+#define CLK_APB0_UART 7
+/* 8 is reserved for CLK_APB0_W1 on A31 */
+#define CLK_APB0_I2C 9
+#define CLK_APB0_TWD 10
+
+#define CLK_IR 11
+
+#endif /* _DT_BINDINGS_CLK_SUN8I_R_CCU_H_ */
--- /dev/null
+/*
+ * Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN8I_DE2_H_
+#define _DT_BINDINGS_RESET_SUN8I_DE2_H_
+
+#define RST_MIXER0 0
+#define RST_MIXER1 1
+#define RST_WB 2
+
+#endif /* _DT_BINDINGS_RESET_SUN8I_DE2_H_ */
--- /dev/null
+/*
+ * Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN8I_R_CCU_H_
+#define _DT_BINDINGS_RST_SUN8I_R_CCU_H_
+
+#define RST_APB0_IR 0
+#define RST_APB0_TIMER 1
+#define RST_APB0_RSB 2
+#define RST_APB0_UART 3
+/* 4 is reserved for RST_APB0_W1 on A31 */
+#define RST_APB0_I2C 5
+
+#endif /* _DT_BINDINGS_RST_SUN8I_R_CCU_H_ */
projects / u-boot / commitdiff