@rm -f $(obj)nand_spl/{u-boot-nand_spl.lds,u-boot-spl,u-boot-spl.map}
@rm -f $(obj)spl/{u-boot-spl,u-boot-spl.bin,u-boot-spl.map}
@rm -f $(obj)spl/{u-boot-spl.lds,u-boot.lst}
- @rm -f $(obj)MLO
+ @rm -f $(obj)MLO MLO.byteswap
@rm -f $(obj)SPL
@rm -f $(obj)tools/xway-swap-bytes
@rm -f $(obj)arch/powerpc/cpu/mpc824x/bedbug_603e.c
boot loader that has already initialized the UART. Define this
variable to flush the UART at init time.
+ CONFIG_SYS_NS16550_BROKEN_TEMT
+
+ 16550 UART set the Transmitter Empty (TEMT) Bit when all output
+ has finished and the transmitter is totally empty. U-Boot waits
+ for this bit to be set to initialize the serial console. On some
+ broken platforms this bit is not set in SPL making U-Boot to
+ hang while waiting for TEMT. Define this option to avoid it.
+
- Console Interface:
Depending on board, define exactly one serial port
CONFIG_CMD_LOADS loads
CONFIG_CMD_MD5SUM print md5 message digest
(requires CONFIG_CMD_MEMORY and CONFIG_MD5)
+ CONFIG_CMD_MEMINFO * Display detailed memory information
CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
loop, loopw, mtest
CONFIG_CMD_MISC Misc functions like sleep etc
run-time determined information about the hardware to the
environment. These will be named board_name, board_rev.
+ CONFIG_DELAY_ENVIRONMENT
+
+ Normally the environment is loaded when the board is
+ intialised so that it is available to U-Boot. This inhibits
+ that so that the environment is not available until
+ explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL
+ this is instead controlled by the value of
+ /config/load-environment.
+
- DataFlash Support:
CONFIG_HAS_DATAFLASH
space for already greatly restricted images, including but not
limited to NAND_SPL configurations.
+- CONFIG_DISPLAY_BOARDINFO
+ Display information about the board that U-Boot is running on
+ when U-Boot starts up. The board function checkboard() is called
+ to do this.
+
+- CONFIG_DISPLAY_BOARDINFO_LATE
+ Similar to the previous option, but display this information
+ later, once stdio is running and output goes to the LCD, if
+ present.
+
Low Level (hardware related) configuration options:
---------------------------------------------------
}
#endif
+#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI)
+void at91_uhp_hw_init(void)
+{
+ /* Enable VBus on UHP ports */
+ at91_set_pio_output(AT91_PIO_PORTD, 18, 0); /* port A */
+ at91_set_pio_output(AT91_PIO_PORTD, 19, 0); /* port B */
+#if defined(CONFIG_USB_OHCI_NEW)
+ /* port C is OHCI only */
+ at91_set_pio_output(AT91_PIO_PORTD, 20, 0); /* port C */
+#endif
+}
+#endif
+
#ifdef CONFIG_MACB
void at91_macb_hw_init(void)
{
#define MPP_CTRL(i) (KW_MPP_BASE + (i* 4))
#define MPP_NR_REGS (1 + MPP_MAX/8)
-void kirkwood_mpp_conf(u32 *mpp_list, u32 *mpp_save)
+void kirkwood_mpp_conf(const u32 *mpp_list, u32 *mpp_save)
{
u32 mpp_ctrl[MPP_NR_REGS];
unsigned int variant_mask;
#define ATMEL_PIO_PORTS 4
#define CPU_HAS_PIO3
#define PIO_SCDR_DIV (0x3fff << 0) /* Slow Clock Divider Mask */
+#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
+#define ATMEL_ID_UHP ATMEL_ID_UHPHS
/*
* at91sam9x5 specific prototypes
| (attr << 8) | (kw_winctrl_calcsize(size) << 16))
#define KWGBE_PORT_SERIAL_CONTROL1_REG(_x) \
- ((_x ? KW_EGIGA0_BASE : KW_EGIGA1_BASE) + 0x44c)
+ ((_x ? KW_EGIGA1_BASE : KW_EGIGA0_BASE) + 0x44c)
#define KW_REG_PCIE_DEVID (KW_REG_PCIE_BASE + 0x00)
#define KW_REG_PCIE_REVID (KW_REG_PCIE_BASE + 0x08)
#define MPP_MAX 49
-void kirkwood_mpp_conf(u32 *mpp_list, u32 *mpp_save);
+void kirkwood_mpp_conf(const u32 *mpp_list, u32 *mpp_save);
#endif
unsigned long reloc_off;
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
unsigned long tlb_addr;
+ unsigned long tlb_size;
#endif
const void *fdt_blob; /* Our device tree, NULL if none */
void **jt; /* jump table */
COBJS-y += board.o
COBJS-y += bootm.o
COBJS-$(CONFIG_SYS_L2_PL310) += cache-pl310.o
-COBJS-y += interrupts.o
-COBJS-y += reset.o
SOBJS-$(CONFIG_USE_ARCH_MEMSET) += memset.o
SOBJS-$(CONFIG_USE_ARCH_MEMCPY) += memcpy.o
else
COBJS-$(CONFIG_SPL_FRAMEWORK) += spl.o
endif
+COBJS-y += interrupts.o
+COBJS-y += reset.o
+
COBJS-y += cache.o
COBJS-y += cache-cp15.o
#include <common.h>
#include <command.h>
+#include <environment.h>
#include <malloc.h>
#include <stdio_dev.h>
#include <version.h>
int power_init_board(void)
__attribute__((weak, alias("__power_init_board")));
+ /* Record the board_init_f() bootstage (after arch_cpu_init()) */
+static int mark_bootstage(void)
+{
+ bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_F, "board_init_f");
+
+ return 0;
+}
+
init_fnc_t *init_sequence[] = {
arch_cpu_init, /* basic arch cpu dependent setup */
-
-#if defined(CONFIG_BOARD_EARLY_INIT_F)
- board_early_init_f,
-#endif
+ mark_bootstage,
#ifdef CONFIG_OF_CONTROL
fdtdec_check_fdt,
+#endif
+#if defined(CONFIG_BOARD_EARLY_INIT_F)
+ board_early_init_f,
#endif
timer_init, /* initialize timer */
#ifdef CONFIG_BOARD_POSTCLK_INIT
void *new_fdt = NULL;
size_t fdt_size = 0;
- bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_F, "board_init_f");
-
memset((void *)gd, 0, sizeof(gd_t));
gd->mon_len = _bss_end_ofs;
#if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
/* reserve TLB table */
- addr -= (4096 * 4);
+ gd->tlb_size = 4096 * 4;
+ addr -= gd->tlb_size;
/* round down to next 64 kB limit */
addr &= ~(0x10000 - 1);
gd->tlb_addr = addr;
- debug("TLB table at: %08lx\n", addr);
+ debug("TLB table from %08lx to %08lx\n", addr, addr + gd->tlb_size);
#endif
/* round down to next 4 kB limit */
#endif
/*
- ************************************************************************
+ * Tell if it's OK to load the environment early in boot.
+ *
+ * If CONFIG_OF_CONFIG is defined, we'll check with the FDT to see
+ * if this is OK (defaulting to saying it's not OK).
+ *
+ * NOTE: Loading the environment early can be a bad idea if security is
+ * important, since no verification is done on the environment.
+ *
+ * @return 0 if environment should not be loaded, !=0 if it is ok to load
+ */
+static int should_load_env(void)
+{
+#ifdef CONFIG_OF_CONTROL
+ return fdtdec_get_config_int(gd->fdt_blob, "load-environment", 0);
+#elif defined CONFIG_DELAY_ENVIRONMENT
+ return 0;
+#else
+ return 1;
+#endif
+}
+
+#if defined(CONFIG_DISPLAY_BOARDINFO_LATE) && defined(CONFIG_OF_CONTROL)
+static void display_fdt_model(const void *blob)
+{
+ const char *model;
+
+ model = (char *)fdt_getprop(blob, 0, "model", NULL);
+ printf("Model: %s\n", model ? model : "<unknown>");
+}
+#endif
+
+/************************************************************************
*
* This is the next part if the initialization sequence: we are now
* running from RAM and have a "normal" C environment, i. e. global
#endif
#ifdef CONFIG_GENERIC_MMC
- puts("MMC: ");
- mmc_initialize(gd->bd);
+ puts("MMC: ");
+ mmc_initialize(gd->bd);
#endif
#ifdef CONFIG_HAS_DATAFLASH
#endif
/* initialize environment */
- env_relocate();
+ if (should_load_env())
+ env_relocate();
+ else
+ set_default_env(NULL);
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
console_init_r(); /* fully init console as a device */
+#ifdef CONFIG_DISPLAY_BOARDINFO_LATE
+# ifdef CONFIG_OF_CONTROL
+ /* Put this here so it appears on the LCD, now it is ready */
+ display_fdt_model(gd->fdt_blob);
+# else
+ checkboard();
+# endif
+#endif
+
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
return;
/* if disabling data cache, disable mmu too */
cache_bit |= CR_M;
- flush_dcache_all();
}
+ reg = get_cr();
+ cp_delay();
+ if (cache_bit == (CR_C | CR_M))
+ flush_dcache_all();
set_cr(reg & ~cache_bit);
}
#endif
NET2BIG_V2_OE_LOW, NET2BIG_V2_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_SPI_SCn,
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
NETSPACE_V2_OE_LOW, NETSPACE_V2_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_SPI_SCn,
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
--- /dev/null
+#
+# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+#
+# Based on Kirkwood support:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+
+include $(TOPDIR)/config.mk
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)../common)
+endif
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := $(BOARD).o ../common/common.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# Copyright (C) 2012 Albert ARIBAUD <albert.u.boot@aribaud.net>
+#
+# Based on netspace_v2 kwbimage.cfg:
+# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+#
+# Based on Kirkwood support:
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand # Boot from NAND flash
+NAND_PAGE_SIZE 800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Values taken from image original LaCie U-Boot header dump!
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1B1B1B9B
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30 # DDR Configuration register
+
+DATA 0xFFD01404 0x37743000 # DDR Controller Control Low
+
+DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1)
+
+DATA 0xFFD0140C 0x00000A19 # DDR Timing (High)
+
+DATA 0xFFD01410 0x0000CCCC # DDR Address Control
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+
+DATA 0xFFD0141C 0x00000662 # DDR Mode
+
+DATA 0xFFD01420 0x00000004 # DDR Extended Mode
+
+DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
+
+DATA 0xFFD01428 0x00096630 # DDR2 ODT Read Timing (default values)
+
+DATA 0xFFD0147C 0x00009663 # DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
+DATA 0xFFD01508 0x00000000 # CS[1]n Base address to 0x0
+DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+DATA 0xFFD0149C 0x0000E40F # CPU ODT Control
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+DATA 0xFFD20134 0x66666666
+DATA 0xFFD20138 0x66666666
+DATA 0xFFD10000 0x01112222
+DATA 0xFFD1000C 0x00000000
+DATA 0xFFD10104 0x00000000
+DATA 0xFFD10100 0x40000000
+# End of Header extension
+DATA 0x0 0x0
--- /dev/null
+/*
+ * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+ *
+ * Based on Kirkwood support:
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include <asm/arch/gpio.h>
+
+#include "../common/common.h"
+#include "netdev.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* GPIO configuration: start FAN at low speed, USB and HDD */
+
+#define WIRELESS_SPACE_OE_LOW 0xFF006808
+#define WIRELESS_SPACE_OE_HIGH 0x0000F989
+#define WIRELESS_SPACE_OE_VAL_LOW 0x00010080
+#define WIRELESS_SPACE_OE_VAL_HIGH 0x00000240
+
+#define WIRELESS_SPACE_REAR_BUTTON 13
+#define WIRELESS_SPACE_FRONT_BUTTON 43
+
+const u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO, /* Fan speed (bit 1) */
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP13_GPIO, /* Red led */
+ MPP14_GPIO, /* USB fuse */
+ MPP15_SATA0_ACTn,
+ MPP16_GPIO, /* SATA 0 power */
+ MPP17_GPIO, /* SATA 1 power */
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0, /* Gigabit Ethernet 1 */
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GE1_8,
+ MPP29_GE1_9,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GE1_14,
+ MPP35_GE1_15,
+ MPP36_GPIO, /* Fan speed (bit 2) */
+ MPP37_GPIO, /* Fan speed (bit 0) */
+ MPP38_GPIO, /* Fan power */
+ MPP39_GPIO, /* Fan rotation fail */
+ MPP40_GPIO, /* Ethernet switch link */
+ MPP41_GPIO, /* USB enable host vbus */
+ MPP42_GPIO, /* LED clock control */
+ MPP43_GPIO, /* WPS button (0=Pushed, 1=Released) */
+ MPP44_GPIO, /* Red LED on/off */
+ MPP45_GPIO, /* Red LED timer blink (on=off=100ms) */
+ MPP46_GPIO, /* Green LED on/off */
+ MPP47_GPIO, /* LED (blue, green) SATA activity blink */
+ MPP48_GPIO, /* Blue LED on/off */
+ 0
+};
+
+struct mv88e61xx_config swcfg = {
+ .name = "egiga0",
+ .vlancfg = MV88E61XX_VLANCFG_ROUTER,
+ .rgmii_delay = MV88E61XX_RGMII_DELAY_EN,
+ .led_init = MV88E61XX_LED_INIT_EN,
+ .mdip = MV88E61XX_MDIP_NOCHANGE,
+ .portstate = MV88E61XX_PORTSTT_FORWARDING,
+ .cpuport = 0x20,
+ .ports_enabled = 0x3F,
+};
+
+int board_early_init_f(void)
+{
+ /* Gpio configuration */
+ kw_config_gpio(WIRELESS_SPACE_OE_VAL_LOW, WIRELESS_SPACE_OE_VAL_HIGH,
+ WIRELESS_SPACE_OE_LOW, WIRELESS_SPACE_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ kirkwood_mpp_conf(kwmpp_config, NULL);
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Machine number */
+ gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
+
+ /* Boot parameters address */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+#if defined(CONFIG_MISC_INIT_R)
+int misc_init_r(void)
+{
+#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
+ if (!getenv("ethaddr")) {
+ uchar mac[6];
+ if (lacie_read_mac_address(mac) == 0)
+ eth_setenv_enetaddr("ethaddr", mac);
+ }
+#endif
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
+/* Configure and initialize PHY */
+void reset_phy(void)
+{
+ /* configure switch on egiga0 */
+ mv88e61xx_switch_initialize(&swcfg);
+}
+#endif
+
+#if defined(CONFIG_KIRKWOOD_GPIO) && defined(CONFIG_WIRELESS_SPACE_CMD)
+/* Return GPIO button status */
+static int
+do_ws(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ if (strcmp(argv[1], "button") == 0) {
+ if (strcmp(argv[2], "rear") == 0)
+ /* invert GPIO result for intuitive while/until use */
+ return !kw_gpio_get_value(WIRELESS_SPACE_REAR_BUTTON);
+ else if (strcmp(argv[2], "front") == 0)
+ return kw_gpio_get_value(WIRELESS_SPACE_FRONT_BUTTON);
+ else
+ return -1;
+ } else {
+ return -1;
+ }
+}
+
+U_BOOT_CMD(ws, 3, 0, do_ws,
+ "Return GPIO button status 0=off 1=on",
+ "- ws button rear|front: test buttons' states\n"
+);
+#endif
DREAMPLUG_OE_LOW, DREAMPLUG_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_SPI_SCn, /* SPI Flash */
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
GURUPLUG_OE_LOW, GURUPLUG_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
MV88F6281GTW_GE_OE_LOW, MV88F6281GTW_GE_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_SPI_SCn,
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
OPENRD_OE_LOW, OPENRD_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
RD6281A_OE_LOW, RD6281A_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
SHEEVAPLUG_OE_LOW, SHEEVAPLUG_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
DOCKSTAR_OE_LOW, DOCKSTAR_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
at91_macb_hw_init();
#endif
+#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI)
+ at91_uhp_hw_init();
+#endif
#ifdef CONFIG_LCD
at91sam9x5ek_lcd_hw_init();
#endif
* you can do this only with a working network connection. Therefore, a random
* ethernet address is generated if none is set and a DHCP request is sent.
* After a successful DHCP response is received, the network settings are
- * configured and the ncip parameter is set to the serverip. Eg. for a working
- * resuce mode, you should set 'next-server' to the host where the netconsole
- * client is started.
+ * configured and the ncip is unset. Therefore, all netconsole packets are
+ * broadcasted.
* Additionally, the bootsource is set to 'rescue'.
*/
* Multi-Purpose Pins Functionality configuration
* These strappings are taken from the original vendor uboot port.
*/
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_SPI_SCn,
MPP1_SPI_MOSI,
MPP2_SPI_SCK,
POGO_E02_OE_LOW, POGO_E02_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
DNS325_OE_LOW, DNS325_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
ICONNECT_OE_LOW, ICONNECT_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
TK71_OE_LOW, TK71_OE_HIGH);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
{
#if defined(CONFIG_HARD_I2C) && !defined(MACH_TYPE_KM_KIRKWOOD)
- immap_t *immap = (immap_t *)CONFIG_SYS_IMMR ;
+ immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c;
/*
#define MASK_RBI_DEFECT_16 0x01
/* Multi-Purpose Pins Functionality configuration */
-u32 kwmpp_config[] = {
+static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
int misc_init_r(void)
{
- char *str;
- int mach_type;
-
- str = getenv("mach_type");
- if (str != NULL) {
- mach_type = simple_strtoul(str, NULL, 10);
- printf("Overwriting MACH_TYPE with %d!!!\n", mach_type);
- gd->bd->bi_arch_number = mach_type;
- }
#if defined(CONFIG_KM_MGCOGE3UN)
char *wait_for_ne;
wait_for_ne = getenv("waitforne");
int board_init(void)
{
- /*
- * arch number of board
- */
- gd->bd->bi_arch_number = MACH_TYPE_KM_KIRKWOOD;
-
/* address of boot parameters */
gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register
DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register
DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register
-DATA 0xFFD20154 0x00000200 # CPU RAM Management Control3 Register
-DATA 0xFFD2014C 0x00001C00 # CPU RAM Management Control1 Register
-DATA 0xFFD20148 0x00000001 # CPU RAM Management Control0 Register
+
+# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched!
+# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage
#Dram initalization
DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register
DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register
DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register
DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register
-DATA 0xFFD20154 0x00000200 # CPU RAM Management Control3 Register
-DATA 0xFFD2014C 0x00001C00 # CPU RAM Management Control1 Register
-DATA 0xFFD20148 0x00000001 # CPU RAM Management Control0 Register
+
+# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched!
+# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage
#Dram initalization
DATA 0xFFD01400 0x43000400 # SDRAM Configuration Register
# bit 19-18: 1, ECC RAM WTC RAM0
# bit 31-20: ???,Reserve
-DATA 0xFFD20154 0x00000200 # CPU RAM Management Control3 Register
-# bit 23-0: 0x000200, Addr Config tuning
-# bit 31-24: 0, Reserved
-
-# ??? Missing register # CPU RAM Management Control2 Register
-
-DATA 0xFFD2014C 0x00001C00 # CPU RAM Management Control1 Register
-# bit 15-0: 0x1C00, Opmux Tuning
-# bit 31-16: 0, Pc Dp Tuning
-
-DATA 0xFFD20148 0x00000001 # CPU RAM Management Control0 Register
-# bit 1-0: 1, addr clk tune
-# bit 3-2: 0, reserved
-# bit 5-4: 0, dtcmp clk tune
-# bit 7-6: 0, reserved
-# bit 9-8: 0, macdrv clk tune
-# bit 11-10: 0, opmuxgm2 clk tune
-# bit 15-14: 0, rf clk tune
-# bit 17-16: 0, rfbypass clk tune
-# bit 19-18: 0, pc dp clk tune
-# bit 23-20: 0, icache clk tune
-# bit 27:24: 0, dcache clk tune
-# bit 31:28: 0, regfile tunin
+# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched!
+# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage
# SDRAM initalization
DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register
# bit 19-18: 1, ECC RAM WTC RAM0
# bit 31-20: ?,Reserved
-DATA 0xFFD20154 0x00000200 # CPU RAM Management Control3 Register
-# bit 23-0: 0x000200, Addr Config tuning
-# bit 31-24: 0, Reserved
-
-# ??? Missing register # CPU RAM Management Control2 Register
-
-DATA 0xFFD2014C 0x00001C00 # CPU RAM Management Control1 Register
-# bit 15-0: 0x1C00, Opmux Tuning
-# bit 31-16: 0, Pc Dp Tuning
-
-DATA 0xFFD20148 0x00000001 # CPU RAM Management Control0 Register
-# bit 1-0: 1, addr clk tune
-# bit 3-2: 0, reserved
-# bit 5-4: 0, dtcmp clk tune
-# bit 7-6: 0, reserved
-# bit 9-8: 0, macdrv clk tune
-# bit 11-10: 0, opmuxgm2 clk tune
-# bit 15-14: 0, rf clk tune
-# bit 17-16: 0, rfbypass clk tune
-# bit 19-18: 0, pc dp clk tune
-# bit 23-20: 0, icache clk tune
-# bit 27:24: 0, dcache clk tune
-# bit 31:28: 0, regfile tunin
+# NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched!
+# If not it could cause KW Exceptions during boot in Fast Corners/High Voltage
# SDRAM initalization
DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register
/* Set SATA activity LEDs to default off */
writel(MVSATAHC_LED_POLARITY_CTRL, MVSATAHC_LED_CONF_REG);
/* Multi-Purpose Pins Functionality configuration */
- u32 kwmpp_config[] = {
+ static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
netspace_max_v2 arm arm926ejs netspace_v2 LaCie kirkwood lacie_kw:NETSPACE_MAX_V2
netspace_mini_v2 arm arm926ejs netspace_v2 LaCie kirkwood lacie_kw:NETSPACE_MINI_V2
netspace_v2 arm arm926ejs netspace_v2 LaCie kirkwood lacie_kw:NETSPACE_V2
+wireless_space arm arm926ejs wireless_space LaCie kirkwood
dreamplug arm arm926ejs - Marvell kirkwood
guruplug arm arm926ejs - Marvell kirkwood
mv88f6281gtw_ge arm arm926ejs - Marvell kirkwood
#include <dataflash.h>
#endif
#include <watchdog.h>
+#include <linux/compiler.h>
+
+DECLARE_GLOBAL_DATA_PTR;
static int mod_mem(cmd_tbl_t *, int, int, int, char * const []);
#endif
+#ifdef CONFIG_CMD_MEMINFO
+__weak void board_show_dram(ulong size)
+{
+ puts("DRAM: ");
+ print_size(size, "\n");
+}
+
+static int do_mem_info(cmd_tbl_t *cmdtp, int flag, int argc,
+ char * const argv[])
+{
+ board_show_dram(gd->ram_size);
+
+ return 0;
+}
+#endif
+
U_BOOT_CMD(
base, 2, 1, do_mem_base,
"print or set address offset",
"[.b, .w, .l] address value delay(ms)"
);
#endif /* CONFIG_MX_CYCLIC */
+
+#ifdef CONFIG_CMD_MEMINFO
+U_BOOT_CMD(
+ meminfo, 3, 1, do_mem_info,
+ "display memory information",
+ ""
+);
+#endif
#include <netdev.h>
#include "mv88e61xx.h"
+/*
+ * Uncomment either of the following line for local debug control;
+ * otherwise global debug control will apply.
+ */
+
+/* #undef DEBUG */
+/* #define DEBUG */
+
#ifdef CONFIG_MV88E61XX_MULTICHIP_ADRMODE
/* Chip Address mode
* The Switch support two modes of operation
return 0;
}
-static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data)
+static void mv88e61xx_switch_write(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 data)
{
u16 mii_dev_addr;
15));
}
-static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data)
+static void mv88e61xx_switch_read(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 *data)
{
u16 mii_dev_addr;
}
#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */
-static void mv88e61xx_port_vlan_config(struct mv88e61xx_config *swconfig,
- u32 max_prtnum, u32 ports_ofs)
-{
- u32 prt;
- u16 reg;
- char *name = swconfig->name;
- u32 cpu_port = swconfig->cpuport;
- u32 port_mask = swconfig->ports_enabled;
- enum mv88e61xx_cfg_vlan vlancfg = swconfig->vlancfg;
-
- /* be sure all ports are disabled */
- for (prt = 0; prt < max_prtnum; prt++) {
- RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, ®);
- reg &= ~0x3;
- WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, reg);
-
- if (!(cpu_port & (1 << prt)))
- continue;
- /* Set CPU port VID to 0x1 */
- RD_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, ®);
- reg &= ~0xfff;
- reg |= 0x1;
- WR_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, reg);
- }
-
- /* Setting Port default priority for all ports to zero */
- for (prt = 0; prt < max_prtnum; prt++) {
- RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, ®);
- reg &= ~0xc000;
- WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, reg);
- }
- /* Setting VID and VID map for all ports except CPU port */
- for (prt = 0; prt < max_prtnum; prt++) {
- /* only for enabled ports */
- if ((1 << prt) & port_mask) {
- /* skip CPU port */
- if ((1 << prt) & cpu_port) {
- /*
- * Set Vlan map table for cpu_port to see
- * all ports
- */
- RD_PHY(name, (ports_ofs + prt),
- MV88E61XX_PRT_VMAP_REG, ®);
- reg &= ~((1 << max_prtnum) - 1);
- reg |= port_mask & ~(1 << prt);
- WR_PHY(name, (ports_ofs + prt),
- MV88E61XX_PRT_VMAP_REG, reg);
- } else {
-
- /*
- * set Ports VLAN Mapping.
- * port prt <--> cpu_port VLAN #prt+1.
- */
- RD_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_VID_REG, ®);
- reg &= ~0x0fff;
- reg |= (prt + 1);
- WR_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_VID_REG, reg);
-
- RD_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_VMAP_REG, ®);
- if (vlancfg == MV88E61XX_VLANCFG_DEFAULT) {
- /*
- * all any port can send frames to all other ports
- * ref: sec 3.2.1.1 of datasheet
- */
- reg |= 0x03f;
- reg &= ~(1 << prt);
- } else if (vlancfg == MV88E61XX_VLANCFG_ROUTER) {
- /*
- * all other ports can send frames to CPU port only
- * ref: sec 3.2.1.2 of datasheet
- */
- reg &= ~((1 << max_prtnum) - 1);
- reg |= cpu_port;
- }
- WR_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_VMAP_REG, reg);
- }
- }
- }
+/*
+ * Convenience macros for switch device/port reads/writes
+ * These macros output valid 'mv88e61xx' U_BOOT_CMDs
+ */
- /*
- * enable only appropriate ports to forwarding mode
- * and disable the others
- */
- for (prt = 0; prt < max_prtnum; prt++) {
- if ((1 << prt) & port_mask) {
- RD_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_CTRL_REG, ®);
- reg |= 0x3;
- WR_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_CTRL_REG, reg);
- } else {
- /* Disable port */
- RD_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_CTRL_REG, ®);
- reg &= ~0x3;
- WR_PHY(name, ports_ofs + prt,
- MV88E61XX_PRT_CTRL_REG, reg);
- }
- }
+#ifndef DEBUG
+#define WR_SWITCH_REG wr_switch_reg
+#define RD_SWITCH_REG rd_switch_reg
+#define WR_SWITCH_PORT_REG(n, p, r, d) \
+ WR_SWITCH_REG(n, (MV88E61XX_PRT_OFST+p), r, d)
+#define RD_SWITCH_PORT_REG(n, p, r, d) \
+ RD_SWITCH_REG(n, (MV88E61XX_PRT_OFST+p), r, d)
+#else
+static void WR_SWITCH_REG(char *name, u32 dev_adr, u32 reg_ofs, u16 data)
+{
+ printf("mv88e61xx %s dev %02x reg %02x write %04x\n",
+ name, dev_adr, reg_ofs, data);
+ wr_switch_reg(name, dev_adr, reg_ofs, data);
}
+static void RD_SWITCH_REG(char *name, u32 dev_adr, u32 reg_ofs, u16 *data)
+{
+ rd_switch_reg(name, dev_adr, reg_ofs, data);
+ printf("mv88e61xx %s dev %02x reg %02x read %04x\n",
+ name, dev_adr, reg_ofs, *data);
+}
+static void WR_SWITCH_PORT_REG(char *name, u32 prt_adr, u32 reg_ofs,
+ u16 data)
+{
+ printf("mv88e61xx %s port %02x reg %02x write %04x\n",
+ name, prt_adr, reg_ofs, data);
+ wr_switch_reg(name, (MV88E61XX_PRT_OFST+prt_adr), reg_ofs, data);
+}
+static void RD_SWITCH_PORT_REG(char *name, u32 prt_adr, u32 reg_ofs,
+ u16 *data)
+{
+ rd_switch_reg(name, (MV88E61XX_PRT_OFST+prt_adr), reg_ofs, data);
+ printf("mv88e61xx %s port %02x reg %02x read %04x\n",
+ name, prt_adr, reg_ofs, *data);
+}
+#endif
+
+/*
+ * Local functions to read/write registers on the switch PHYs.
+ * NOTE! This goes through switch, not direct miiphy, writes and reads!
+ */
/*
* Make sure SMIBusy bit cleared before another
u16 reg = 0;
u32 timeout = MV88E61XX_PHY_TIMEOUT;
do {
- RD_PHY(name, MV88E61XX_GLB2REG_DEVADR,
+ rd_switch_reg(name, MV88E61XX_GLB2REG_DEVADR,
MV88E61XX_PHY_CMD, ®);
if (timeout-- == 0) {
printf("SMI busy timeout\n");
return 0;
}
+static inline int mv88e61xx_switch_miiphy_write(char *name, u32 phy,
+ u32 reg, u16 data)
+{
+ /* write switch data reg then cmd reg then check completion */
+ wr_switch_reg(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA,
+ data);
+ wr_switch_reg(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_CMD,
+ (MV88E61XX_PHY_WRITE_CMD | (phy << 5) | reg));
+ return mv88e61xx_busychk(name);
+}
+
+static inline int mv88e61xx_switch_miiphy_read(char *name, u32 phy,
+ u32 reg, u16 *data)
+{
+ /* write switch cmd reg, check for completion */
+ wr_switch_reg(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_CMD,
+ (MV88E61XX_PHY_READ_CMD | (phy << 5) | reg));
+ if (mv88e61xx_busychk(name))
+ return -1;
+ /* read switch data reg and return success */
+ rd_switch_reg(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, data);
+ return 0;
+}
+
+/*
+ * Convenience macros for switch PHY reads/writes
+ */
+
+#ifndef DEBUG
+#define WR_SWITCH_PHY_REG mv88e61xx_switch_miiphy_write
+#define RD_SWITCH_PHY_REG mv88e61xx_switch_miiphy_read
+#else
+static inline int WR_SWITCH_PHY_REG(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 data)
+{
+ int r = mv88e61xx_switch_miiphy_write(name, phy_adr, reg_ofs, data);
+ if (r)
+ printf("** ERROR writing mv88e61xx %s phy %02x reg %02x\n",
+ name, phy_adr, reg_ofs);
+ else
+ printf("mv88e61xx %s phy %02x reg %02x write %04x\n",
+ name, phy_adr, reg_ofs, data);
+ return r;
+}
+static inline int RD_SWITCH_PHY_REG(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 *data)
+{
+ int r = mv88e61xx_switch_miiphy_read(name, phy_adr, reg_ofs, data);
+ if (r)
+ printf("** ERROR reading mv88e61xx %s phy %02x reg %02x\n",
+ name, phy_adr, reg_ofs);
+ else
+ printf("mv88e61xx %s phy %02x reg %02x read %04x\n",
+ name, phy_adr, reg_ofs, *data);
+ return r;
+}
+#endif
+
+static void mv88e61xx_port_vlan_config(struct mv88e61xx_config *swconfig)
+{
+ u32 prt;
+ u16 reg;
+ char *name = swconfig->name;
+ u32 port_mask = swconfig->ports_enabled;
+
+ /* apply internal vlan config */
+ for (prt = 0; prt < MV88E61XX_MAX_PORTS_NUM; prt++) {
+ /* only for enabled ports */
+ if ((1 << prt) & port_mask) {
+ /* take vlan map from swconfig */
+ u8 vlanmap = swconfig->vlancfg[prt];
+ /* remove disabled ports from vlan map */
+ vlanmap &= swconfig->ports_enabled;
+ /* apply vlan map to port */
+ RD_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_VMAP_REG, ®);
+ reg &= ~((1 << MV88E61XX_MAX_PORTS_NUM) - 1);
+ reg |= vlanmap;
+ WR_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_VMAP_REG, reg);
+ }
+ }
+}
+
/*
* Power up the specified port and reset PHY
*/
-static int mv88361xx_powerup(struct mv88e61xx_config *swconfig, u32 prt)
+static int mv88361xx_powerup(struct mv88e61xx_config *swconfig, u32 phy)
{
char *name = swconfig->name;
- /* Write Copper Specific control reg1 (0x14) for-
+ /* Write Copper Specific control reg1 (0x10) for-
* Enable Phy power up
* Energy Detect on (sense&Xmit NLP Periodically
* reset other settings default
*/
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x3360);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (0x9410 | (prt << 5)));
-
- if (mv88e61xx_busychk(name))
+ if (WR_SWITCH_PHY_REG(name, phy, 0x10, 0x3360))
return -1;
/* Write PHY ctrl reg (0x0) to apply
* Phy reset (set bit 15 low)
* reset other default values
*/
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x1140);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (0x9400 | (prt << 5)));
-
- if (mv88e61xx_busychk(name))
+ if (WR_SWITCH_PHY_REG(name, phy, 0x00, 0x9140))
return -1;
return 0;
* to setup PHY LEDs default configuration to detect 10/100/1000Mb/s
* Link status
*/
-static int mv88361xx_led_init(struct mv88e61xx_config *swconfig, u32 prt)
+static int mv88361xx_led_init(struct mv88e61xx_config *swconfig, u32 phy)
{
char *name = swconfig->name;
- u16 reg;
if (swconfig->led_init != MV88E61XX_LED_INIT_EN)
return 0;
/* set page address to 3 */
- reg = 3;
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
- 1 << MV88E61XX_MODE_OFST |
- 1 << MV88E61XX_OP_OFST |
- prt << MV88E61XX_ADDR_OFST | 22));
-
- if (mv88e61xx_busychk(name))
+ if (WR_SWITCH_PHY_REG(name, phy, 0x16, 0x0003))
return -1;
- /* set LED Func Ctrl reg */
- reg = 1; /* LED[0] On-Link, Blink-Activity, Off-NoLink */
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
- 1 << MV88E61XX_MODE_OFST |
- 1 << MV88E61XX_OP_OFST |
- prt << MV88E61XX_ADDR_OFST | 16));
-
- if (mv88e61xx_busychk(name))
+ /*
+ * set LED Func Ctrl reg
+ * value 0x0001 = LED[0] On-Link, Blink-Activity, Off-NoLink
+ */
+ if (WR_SWITCH_PHY_REG(name, phy, 0x10, 0x0001))
return -1;
/* set page address to 0 */
- reg = 0;
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
- 1 << MV88E61XX_MODE_OFST |
- 1 << MV88E61XX_OP_OFST |
- prt << MV88E61XX_ADDR_OFST | 22));
-
- if (mv88e61xx_busychk(name))
+ if (WR_SWITCH_PHY_REG(name, phy, 0x16, 0x0000))
return -1;
return 0;
* This is optional settings may be needed on some boards
* for PHY<->magnetics h/w tuning
*/
-static int mv88361xx_reverse_mdipn(struct mv88e61xx_config *swconfig, u32 prt)
+static int mv88361xx_reverse_mdipn(struct mv88e61xx_config *swconfig, u32 phy)
{
char *name = swconfig->name;
- u16 reg;
if (swconfig->mdip != MV88E61XX_MDIP_REVERSE)
return 0;
- reg = 0x0f; /*Reverse MDIP/N[3:0] bits */
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
- WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
- MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
- 1 << MV88E61XX_MODE_OFST |
- 1 << MV88E61XX_OP_OFST |
- prt << MV88E61XX_ADDR_OFST | 20));
-
- if (mv88e61xx_busychk(name))
+ /*Reverse MDIP/N[3:0] bits */
+ if (WR_SWITCH_PHY_REG(name, phy, 0x14, 0x000f))
return -1;
return 0;
u16 reg;
char *idstr;
char *name = swconfig->name;
+ int time;
if (miiphy_set_current_dev(name)) {
printf("%s failed\n", __FUNCTION__);
printf("Invalid cpu port config, using default port5\n");
}
- RD_PHY(name, MV88E61XX_PRT_OFST, MII_PHYSID2, ®);
+ RD_SWITCH_PORT_REG(name, 0, MII_PHYSID2, ®);
switch (reg &= 0xfff0) {
case 0x1610:
idstr = "88E6161";
break;
}
- /* Port based VLANs configuration */
- if ((swconfig->vlancfg == MV88E61XX_VLANCFG_DEFAULT)
- || (swconfig->vlancfg == MV88E61XX_VLANCFG_ROUTER))
- mv88e61xx_port_vlan_config(swconfig, MV88E61XX_MAX_PORTS_NUM,
- MV88E61XX_PRT_OFST);
- else {
- printf("Unsupported mode %s failed\n", __FUNCTION__);
- return -1;
+ /* be sure all ports are disabled */
+ for (prt = 0; prt < MV88E61XX_MAX_PORTS_NUM; prt++) {
+ RD_SWITCH_PORT_REG(name, prt, MV88E61XX_PRT_CTRL_REG, ®);
+ reg &= ~0x3;
+ WR_SWITCH_PORT_REG(name, prt, MV88E61XX_PRT_CTRL_REG, reg);
}
+ /* wait 2 ms for queues to drain */
+ udelay(2000);
+
+ /* reset switch */
+ RD_SWITCH_REG(name, MV88E61XX_GLBREG_DEVADR, MV88E61XX_SGCR, ®);
+ reg |= 0x8000;
+ WR_SWITCH_REG(name, MV88E61XX_GLBREG_DEVADR, MV88E61XX_SGCR, reg);
+
+ /* wait up to 1 second for switch reset complete */
+ for (time = 1000; time; time--) {
+ RD_SWITCH_REG(name, MV88E61XX_GLBREG_DEVADR, MV88E61XX_SGSR,
+ ®);
+ if ((reg & 0xc800) == 0xc800)
+ break;
+ udelay(1000);
+ }
+ if (!time)
+ return -1;
+
+ /* Port based VLANs configuration */
+ mv88e61xx_port_vlan_config(swconfig);
+
if (swconfig->rgmii_delay == MV88E61XX_RGMII_DELAY_EN) {
/*
* Enable RGMII delay on Tx and Rx for CPU port
* Ref: sec 9.5 of chip datasheet-02
*/
- WR_PHY(name, MV88E61XX_PRT_OFST + 5,
- MV88E61XX_RGMII_TIMECTRL_REG, 0x18);
- WR_PHY(name, MV88E61XX_PRT_OFST + 4,
- MV88E61XX_RGMII_TIMECTRL_REG, 0xc1e7);
+ /*Force port link down */
+ WR_SWITCH_PORT_REG(name, 5, MV88E61XX_PCS_CTRL_REG, 0x10);
+ /* configure port RGMII delay */
+ WR_SWITCH_PORT_REG(name, 4,
+ MV88E61XX_RGMII_TIMECTRL_REG, 0x81e7);
+ RD_SWITCH_PORT_REG(name, 5,
+ MV88E61XX_RGMII_TIMECTRL_REG, ®);
+ WR_SWITCH_PORT_REG(name, 5,
+ MV88E61XX_RGMII_TIMECTRL_REG, reg | 0x18);
+ WR_SWITCH_PORT_REG(name, 4,
+ MV88E61XX_RGMII_TIMECTRL_REG, 0xc1e7);
+ /* Force port to RGMII FDX 1000Base then up */
+ WR_SWITCH_PORT_REG(name, 5, MV88E61XX_PCS_CTRL_REG, 0x1e);
+ WR_SWITCH_PORT_REG(name, 5, MV88E61XX_PCS_CTRL_REG, 0x3e);
}
for (prt = 0; prt < MV88E61XX_MAX_PORTS_NUM; prt++) {
- if (!((1 << prt) & swconfig->cpuport)) {
- if (mv88361xx_led_init(swconfig, prt))
+ /* configure port's PHY */
+ if (!((1 << prt) & swconfig->cpuport)) {
+ /* port 4 has phy 6, not 4 */
+ int phy = (prt == 4) ? 6 : prt;
+ if (mv88361xx_powerup(swconfig, phy))
return -1;
- if (mv88361xx_reverse_mdipn(swconfig, prt))
+ if (mv88361xx_reverse_mdipn(swconfig, phy))
return -1;
- if (mv88361xx_powerup(swconfig, prt))
+ if (mv88361xx_led_init(swconfig, phy))
return -1;
}
+ /* set port VID to port+1 except for cpu port */
+ if (!((1 << prt) & swconfig->cpuport)) {
+ RD_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_VID_REG, ®);
+ WR_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_VID_REG,
+ (reg & ~1023) | (prt+1));
+ }
+
/*Program port state */
- RD_PHY(name, MV88E61XX_PRT_OFST + prt,
- MV88E61XX_PRT_CTRL_REG, ®);
- WR_PHY(name, MV88E61XX_PRT_OFST + prt,
- MV88E61XX_PRT_CTRL_REG,
- reg | (swconfig->portstate & 0x03));
+ RD_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_CTRL_REG, ®);
+ WR_SWITCH_PORT_REG(name, prt,
+ MV88E61XX_PRT_CTRL_REG,
+ reg | (swconfig->portstate & 0x03));
+
}
printf("%s Initialized on %s\n", idstr, name);
return 0;
}
+
+#ifdef CONFIG_MV88E61XX_CMD
+static int
+do_switch(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ char *name, *endp;
+ int write = 0;
+ enum { dev, prt, phy } target = dev;
+ u32 addrlo, addrhi, addr;
+ u32 reglo, reghi, reg;
+ u16 data, rdata;
+
+ if (argc < 7)
+ return -1;
+
+ name = argv[1];
+
+ if (strcmp(argv[2], "phy") == 0)
+ target = phy;
+ else if (strcmp(argv[2], "port") == 0)
+ target = prt;
+ else if (strcmp(argv[2], "dev") != 0)
+ return 1;
+
+ addrlo = simple_strtoul(argv[3], &endp, 16);
+
+ if (!*endp) {
+ addrhi = addrlo;
+ } else {
+ while (*endp < '0' || *endp > '9')
+ endp++;
+ addrhi = simple_strtoul(endp, NULL, 16);
+ }
+
+ reglo = simple_strtoul(argv[5], &endp, 16);
+ if (!*endp) {
+ reghi = reglo;
+ } else {
+ while (*endp < '0' || *endp > '9')
+ endp++;
+ reghi = simple_strtoul(endp, NULL, 16);
+ }
+
+ if (strcmp(argv[6], "write") == 0)
+ write = 1;
+ else if (strcmp(argv[6], "read") != 0)
+ return 1;
+
+ data = simple_strtoul(argv[7], NULL, 16);
+
+ for (addr = addrlo; addr <= addrhi; addr++) {
+ for (reg = reglo; reg <= reghi; reg++) {
+ if (write) {
+ if (target == phy)
+ mv88e61xx_switch_miiphy_write(
+ name, addr, reg, data);
+ else if (target == prt)
+ wr_switch_reg(name,
+ addr+MV88E61XX_PRT_OFST,
+ reg, data);
+ else
+ wr_switch_reg(name, addr, reg, data);
+ } else {
+ if (target == phy)
+ mv88e61xx_switch_miiphy_read(
+ name, addr, reg, &rdata);
+ else if (target == prt)
+ rd_switch_reg(name,
+ addr+MV88E61XX_PRT_OFST,
+ reg, &rdata);
+ else
+ rd_switch_reg(name, addr, reg, &rdata);
+ printf("%s %s %s %02x %s %02x %s %04x\n",
+ argv[0], argv[1], argv[2], addr,
+ argv[4], reg, argv[6], rdata);
+ if (write && argc == 7 && rdata != data)
+ return 1;
+ }
+ }
+ }
+ return 0;
+}
+
+U_BOOT_CMD(mv88e61xx, 8, 0, do_switch,
+ "Read or write mv88e61xx switch registers",
+ "<ethdevice> dev|port|phy <addr> reg <reg> write <data>\n"
+ "<ethdevice> dev|port|phy <addr> reg <reg> read [<data>]\n"
+ " - read/write switch device, port or phy at (addr,reg)\n"
+ " addr=0..0x1C for dev, 0..5 for port or phy.\n"
+ " reg=0..0x1F.\n"
+ " data=0..0xFFFF (tested if present against actual read).\n"
+ " All numeric parameters are assumed to be hex.\n"
+ " <addr> and <<reg> arguments can be ranges (x..y)"
+);
+#endif /* CONFIG_MV88E61XX_CMD */
#include <miiphy.h>
#define MV88E61XX_CPU_PORT 0x5
-#define MV88E61XX_MAX_PORTS_NUM 0x6
#define MV88E61XX_PHY_TIMEOUT 100000
-#define MV88E61XX_PRT_STS_REG 0x1
+/* port dev-addr (= port + 0x10) */
+#define MV88E61XX_PRT_OFST 0x10
+/* port registers */
+#define MV88E61XX_PCS_CTRL_REG 0x1
#define MV88E61XX_PRT_CTRL_REG 0x4
#define MV88E61XX_PRT_VMAP_REG 0x6
#define MV88E61XX_PRT_VID_REG 0x7
+#define MV88E61XX_RGMII_TIMECTRL_REG 0x1A
-#define MV88E61XX_PRT_OFST 0x10
+/* global registers dev-addr */
+#define MV88E61XX_GLBREG_DEVADR 0x1B
+/* global registers */
+#define MV88E61XX_SGSR 0x00
+#define MV88E61XX_SGCR 0x04
+
+/* global 2 registers dev-addr */
+#define MV88E61XX_GLB2REG_DEVADR 0x1C
+/* global 2 registers */
#define MV88E61XX_PHY_CMD 0x18
#define MV88E61XX_PHY_DATA 0x19
-#define MV88E61XX_RGMII_TIMECTRL_REG 0x1A
-#define MV88E61XX_GLB2REG_DEVADR 0x1C
+/* global 2 phy commands */
+#define MV88E61XX_PHY_WRITE_CMD 0x9400
+#define MV88E61XX_PHY_READ_CMD 0x9800
#define MV88E61XX_BUSY_OFST 15
#define MV88E61XX_MODE_OFST 12
-#define MV88E61XX_OP_OFST 10
+#define MV88E61XX_OP_OFST 10
#define MV88E61XX_ADDR_OFST 5
#ifdef CONFIG_MV88E61XX_MULTICHIP_ADRMODE
static int mv88e61xx_busychk_multic(char *name, u32 devaddr);
-static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data);
-static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data);
-#define WR_PHY mv88e61xx_wr_phy
-#define RD_PHY mv88e61xx_rd_phy
+static void mv88e61xx_switch_write(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 data);
+static void mv88e61xx_switch_read(char *name, u32 phy_adr,
+ u32 reg_ofs, u16 *data);
+#define wr_switch_reg mv88e61xx_switch_write
+#define rd_switch_reg mv88e61xx_switch_read
#else
-#define WR_PHY miiphy_write
-#define RD_PHY miiphy_read
+/* switch appears a s simple PHY and can thus use miiphy */
+#define wr_switch_reg miiphy_write
+#define rd_switch_reg miiphy_read
#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */
#endif /* _MV88E61XX_H */
void NS16550_init(NS16550_t com_port, int baud_divisor)
{
+#if (!defined(CONFIG_SYS_NS16550_BROKEN_TEMT))
while (!(serial_in(&com_port->lsr) & UART_LSR_TEMT))
;
+#endif
serial_out(CONFIG_SYS_NS16550_IER, &com_port->ier);
#if (defined(CONFIG_OMAP) && !defined(CONFIG_OMAP3_ZOOM2)) || \
as->slave.cs = cs;
as->regs = regs;
as->mr = ATMEL_SPI_MR_MSTR | ATMEL_SPI_MR_MODFDIS
-#if defined(CONFIG_AT91SAM9X5)
+#if defined(CONFIG_AT91SAM9X5) || defined(CONFIG_AT91SAM9M10G45)
| ATMEL_SPI_MR_WDRBT
#endif
| ATMEL_SPI_MR_PCS(~(1 << cs) & 0xf);
{
struct spi_slave *slave;
u32 data;
- u32 kwspi_mpp_config[] = { 0, 0 };
+ static const u32 kwspi_mpp_config[2][2] = {
+ { MPP0_SPI_SCn, 0 }, /* if cs == 0 */
+ { MPP7_SPI_SCn, 0 } /* if cs != 0 */
+ };
if (!spi_cs_is_valid(bus, cs))
return NULL;
writel(KWSPI_IRQMASK, &spireg->irq_mask);
/* program mpp registers to select SPI_CSn */
- if (cs) {
- kwspi_mpp_config[0] = MPP7_SPI_SCn;
- } else {
- kwspi_mpp_config[0] = MPP0_SPI_SCn;
- }
- kirkwood_mpp_conf(kwspi_mpp_config, cs_spi_mpp_back);
+ kirkwood_mpp_conf(kwspi_mpp_config[cs ? 1 : 0], cs_spi_mpp_back);
return slave;
}
writel(get_pllb_init(), &pmc->pllbr);
while ((readl(&pmc->sr) & AT91_PMC_LOCKB) != AT91_PMC_LOCKB)
;
-#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45)
+#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) || \
+ defined(CONFIG_AT91SAM9X5)
/* Enable UPLL */
writel(readl(&pmc->uckr) | AT91_PMC_UPLLEN | AT91_PMC_BIASEN,
&pmc->uckr);
writel(0, &pmc->pllbr);
while ((readl(&pmc->sr) & AT91_PMC_LOCKB) != 0)
;
-#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45)
+#elif defined(CONFIG_AT91SAM9G45) || defined(CONFIG_AT91SAM9M10G45) || \
+ defined(CONFIG_AT91SAM9X5)
/* Disable UPLL */
writel(readl(&pmc->uckr) & (~AT91_PMC_UPLLEN), &pmc->uckr);
while ((readl(&pmc->sr) & AT91_PMC_LOCKU) == AT91_PMC_LOCKU)
extern u8 _binary_dt_dtb_start[]; /* embedded device tree blob */
int set_cpu_clk_info(void);
+/**
+ * Show the DRAM size in a board-specific way
+ *
+ * This is used by boards to display DRAM information in their own way.
+ *
+ * @param size Size of DRAM (which should be displayed along with other info)
+ */
+void board_show_dram(ulong size);
+
/* common/flash.c */
void flash_perror (int);
#define CONFIG_CMD_LICENSE /* console license display */
#define CONFIG_CMD_LOADB /* loadb */
#define CONFIG_CMD_LOADS /* loads */
+#define CONFIG_CMD_MEMINFO /* meminfo */
#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */
#define CONFIG_CMD_MFSL /* FSL support for Microblaze */
#define CONFIG_CMD_MII /* MII support */
#define CONFIG_CMD_NAND
#define CONFIG_CMD_SF
#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_USB
+
+/*
+ * define CONFIG_USB_EHCI to enable USB Hi-Speed (aka 2.0)
+ * NB: in this case, USB 1.1 devices won't be recognized.
+ */
+
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
/* MMC */
#ifdef CONFIG_CMD_MMC
#define CONFIG_MMC
-#define CONFIG_CMD_FAT
#define CONFIG_GENERIC_MMC
#define CONFIG_GENERIC_ATMEL_MCI
+#endif
+
+/* FAT */
+#ifdef CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_MACB_SEARCH_PHY
+/* USB */
+#ifdef CONFIG_CMD_USB
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_ATMEL
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
+#else
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
+#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9x5"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3
+#endif
+#define CONFIG_USB_ATMEL
+#define CONFIG_USB_STORAGE
+#endif
+
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+/* define to avoid U-Boot to hang while waiting for TEMT */
+#define CONFIG_SYS_NS16550_BROKEN_TEMT
+
/* select serial console configuration */
#define CONFIG_CONS_INDEX 3
#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
"load=tftpboot ${load_addr_r} ${u-boot}\0" \
"mtdids=" MTDIDS_DEFAULT "\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
- "stderr=serial\0" \
- "stdin=serial\0" \
- "stdout=serial\0" \
""
#endif /* CONFIG_KM_DEF_ENV */
"config_nc_dhcp=setenv autoload_old ${autoload}; " \
"setenv autoload no " \
"&& bootp " \
- "&& setenv ncip ${serverip} " \
+ "&& setenv ncip " \
"&& setenv autoload ${autoload_old}; " \
"setenv autoload_old\0" \
"standard_env=setenv ipaddr; setenv netmask; setenv serverip; " \
/*
* Size of malloc() pool
*/
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024 * 4) /* 4MiB for malloc() */
/*
* Other required minimal configurations
--- /dev/null
+/*
+ * Copyright (C) 2011 Albert ARIBAUD <albert.u.boot@aribaud.net>
+ *
+ * Based on the netspace_v2 code which is
+ * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CONFIG_WIRELESS_SPACE_H
+#define _CONFIG_WIRELESS_SPACE_H
+
+/*
+ * Machine number definition
+ */
+#define MACH_TYPE_WIRELESS_SPACE 2500 /* is missing in mach-types.h */
+#define CONFIG_MACH_TYPE MACH_TYPE_WIRELESS_SPACE
+#define CONFIG_IDENT_STRING " Wireless Space"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD /* SoC Family Name */
+/* SoC name */
+#define CONFIG_KW88F6281
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* no NOR or SPI flash */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_USB
+
+/*
+ * Core clock definition
+ */
+#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
+
+/*
+ * SDRAM configuration
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+
+/*
+ * Different SDRAM configuration and size for some of the boards derived
+ * from the Network Space v2
+ */
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/* Remove or override few declarations from mv-common.h */
+#undef CONFIG_RBTREE
+#undef CONFIG_SYS_IDE_MAXBUS
+#undef CONFIG_SYS_IDE_MAXDEVICE
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE 1
+#undef CONFIG_SYS_PROMPT
+#define CONFIG_SYS_PROMPT "ws> "
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MISC_INIT_R /* misc_init_r() initializes MAC address */
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable only egiga0... */
+#define PORT_SERIAL_CONTROL_VALUE 0x00A4260E /* ... tied to the switch... */
+#define CONFIG_PHY_BASE_ADR 0xa /* ... through a 'fake' PHY */
+#define CONFIG_MII
+#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+#define CONFIG_NETCONSOLE
+#define CONFIG_MV88E61XX_SWITCH
+#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE
+#define CONFIG_MV88E61XX_CMD
+#define CONFIG_CMD_TFTPPUT
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * SATA Driver configuration
+ */
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+#endif /* CONFIG_MVSATA_IDE */
+
+/*
+ * Enable GPI0 support
+ */
+#define CONFIG_KIRKWOOD_GPIO
+
+/*
+ * Enable I2C support
+ */
+#ifdef CONFIG_CMD_I2C
+/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */
+#endif /* CONFIG_CMD_I2C */
+
+/*
+ * Partition support
+ */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+
+/*
+ * File systems support
+ */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+
+/*
+ * Use the HUSH parser
+ */
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Console configuration
+ */
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+
+/*
+ * Enable device tree support
+ */
+#define CONFIG_OF_LIBFDT
+
+/*
+ * Environment variables configurations
+ */
+
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128KB */
+#define CONFIG_ENV_SIZE 0x20000 /* 128KB */
+#define CONFIG_ENV_OFFSET 0x80000 /* env starts here */
+
+/*
+ * Board-specific command to make using buttons etc easier
+ */
+
+#define CONFIG_WIRELESS_SPACE_CMD
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_PREBOOT
+
+#define CONFIG_BOOTARGS "console=ttyS0,115200"
+
+#define CONFIG_BOOTCOMMAND \
+ "if run usbload || run diskload; then bootm; fi"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "stdin=serial\0" \
+ "stdout=serial\0" \
+ "stderr=serial\0" \
+ "bootfile=uImage\0" \
+ "loadaddr=0x800000\0" \
+ "autoload=no\0" \
+ "netconsole=" \
+ "set stdin $stdin,nc; " \
+ "set stdout $stdout,nc; " \
+ "set stderr $stderr,nc;\0" \
+ "diskload=ide reset && " \
+ "ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \
+ "usbload=usb start && " \
+ "fatload usb 0:1 $loadaddr /boot/$bootfile\0" \
+ "preboot=" \
+ "dhcp && run netconsole\0"
+
+#endif /* _CONFIG_WIRELESS_SPACE_H */
* the stuct and enums here are used to specify switch configuration params
*/
#if defined(CONFIG_MV88E61XX_SWITCH)
-enum mv88e61xx_cfg_vlan {
- MV88E61XX_VLANCFG_DEFAULT,
- MV88E61XX_VLANCFG_ROUTER
-};
+
+/* constants for any 88E61xx switch */
+#define MV88E61XX_MAX_PORTS_NUM 6
enum mv88e61xx_cfg_mdip {
MV88E61XX_MDIP_NOCHANGE,
struct mv88e61xx_config {
char *name;
- enum mv88e61xx_cfg_vlan vlancfg;
+ u8 vlancfg[MV88E61XX_MAX_PORTS_NUM];
enum mv88e61xx_cfg_rgmiid rgmii_delay;
enum mv88e61xx_cfg_prtstt portstate;
enum mv88e61xx_cfg_ledinit led_init;
u8 cpuport;
};
+/*
+ * Common mappings for Internal VLANs
+ * These mappings consider that all ports are useable; the driver
+ * will mask inexistent/unused ports.
+ */
+
+/* Switch mode : routes any port to any port */
+#define MV88E61XX_VLANCFG_SWITCH { 0x3F, 0x3F, 0x3F, 0x3F, 0x3F, 0x3F }
+
+/* Router mode: routes only CPU port 5 to/from non-CPU ports 0-4 */
+#define MV88E61XX_VLANCFG_ROUTER { 0x20, 0x20, 0x20, 0x20, 0x20, 0x1F }
+
int mv88e61xx_switch_initialize(struct mv88e61xx_config *swconfig);
#endif /* CONFIG_MV88E61XX_SWITCH */
projects / u-boot / commitdiff