ethernet2 = ð1;
ethernet3 = ð2;
spi1 = &spi1;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
};
chosen {
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Allied Telesis SBx81LIFKW Board";
+ compatible = "atl,SBx81LIFKW", "marvell,kirkwood-88f6281",
+ "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x08000000>; /* 128 MB */
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ aliases {
+ ethernet0 = ð0;
+ i2c0 = &i2c0;
+ spi0 = &spi0;
+ };
+
+ dsa {
+ compatible = "marvell,dsa";
+ #address-cells = <2>;
+ #size-cells = <0>;
+ dsa,ethernet = <ð0>;
+ dsa,mii-bus = <&mdio>;
+ status = "okay";
+
+ switch@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1 0>;
+
+ port@0 {
+ reg = <0>;
+ label = "internal0";
+ };
+ port@1 {
+ reg = <1>;
+ label = "internal1";
+ };
+ port@8 {
+ reg = <8>;
+ label = "internal8";
+ phy-mode = "rgmii-id";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ port@9 {
+ reg = <9>;
+ label = "internal9";
+ phy-mode = "rgmii-id";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ port@10 {
+ reg = <10>;
+ label = "cpu";
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p128", "jedec,spi-nor", "spi-flash";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ mode = <0>;
+
+ partition@u-boot {
+ reg = <0x00000000 0x00c00000>;
+ label = "u-boot";
+ };
+ partition@u-boot-env {
+ reg = <0x00c00000 0x00040000>;
+ label = "u-boot-env";
+ };
+ partition@unused {
+ reg = <0x00100000 0x00f00000>;
+ label = "unused";
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ eeprom@52 {
+ compatible = "atmel,24c04";
+ reg = <0x52>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+};
+
+ð0 {
+ status = "okay";
+
+ ethernet0-port@0 {
+ speed = <1000>;
+ duplex = <1>;
+ };
+};
+
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
stdout-path = &uart0;
};
+ aliases {
+ spi0 = &spi0;
+ };
+
ocp@f1000000 {
pinctrl: pin-controller@10000 {
pmx_power_hdd: pmx-power-hdd {
config TARGET_NSA310S
bool "Zyxel NSA310S"
+config TARGET_SBx81LIFKW
+ bool "Allied Telesis SBx81GS24/SBx81GT40/SBx81XS6/SBx81XS16"
+
endchoice
config SYS_SOC
source "board/Seagate/goflexhome/Kconfig"
source "board/Seagate/nas220/Kconfig"
source "board/zyxel/nsa310s/Kconfig"
+source "board/alliedtelesis/SBx81LIFKW/Kconfig"
endif
* SPI Flash configuration
*/
#ifdef CONFIG_CMD_SF
-#define CONFIG_HARD_SPI 1
#ifndef CONFIG_ENV_SPI_BUS
# define CONFIG_ENV_SPI_BUS 0
#endif
/*
* I2C related stuff
*/
-#ifdef CONFIG_CMD_I2C
+#if defined(CONFIG_CMD_I2C) && !defined(CONFIG_DM_I2C)
#ifndef CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
{LANE_CFG4_REG, 0x800, 0x8, {0x8}, 0, 0},
/* tximpcal_th and rximpcal_th */
{VTHIMPCAL_CTRL_REG, 0x800, 0xff00, {0x3000}, 0, 0},
+ /* Force receiver detected */
+ {LANE_CFG0_REG, 0x800, 0x8000, {0x8000}, 0, 0},
};
/* PEX - configuration seq for REF_CLOCK_25MHz */
#define RX_REG3 0xa0188
#define PCIE_REG1 0xa0288
#define PCIE_REG3 0xa0290
+#define LANE_CFG0_REG 0xa0600
#define LANE_CFG1_REG 0xa0604
#define LANE_CFG4_REG 0xa0620
#define LANE_CFG5_REG 0xa0624
--- /dev/null
+if TARGET_SBx81LIFKW
+
+config SYS_BOARD
+ default "SBx81LIFKW"
+
+config SYS_VENDOR
+ default "alliedtelesis"
+
+config SYS_CONFIG_NAME
+ default "SBx81LIFKW"
+
+endif
--- /dev/null
+SBx81LIFKW BOARD
+M: Chris Packham <chris.packham@alliedtelesis.co.nz>
+S: Maintained
+F: board/alliedtelesis/SBx81LIFKW/
+F: include/configs/SBx81LIFKW
+F: configs/SBx81LIFKW_defconfig
+F: arch/arm/dts/kirkwood-atl-sbx81lifkw.dts
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2010, 2018
+# Allied Telesis <www.alliedtelesis.com>
+#
+
+obj-y += sbx81lifkw.o
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2018 Allied Telesis
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM spi # Boot from SPI flash
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+DATA 0xffd100e0 0x1b1b1b1b
+DATA 0xffd20134 0xffffffff
+DATA 0xffd20138 0x009fffff
+DATA 0xffd20154 0x00000000
+DATA 0xffd2014c 0x00000000
+DATA 0xffd20148 0x00000001
+
+# Dram initalization for 1 x x16
+# DDR II Micron part number MT47H64M16HR-3
+# MClk 333MHz, Size 128MB, ECC disable
+#
+DATA 0xffd01400 0x43000618
+DATA 0xffd01404 0x35143000
+DATA 0xffd01408 0x11012227
+DATA 0xffd0140c 0x00000819
+DATA 0xffd01410 0x0000000d
+DATA 0xffd01414 0x00000000
+DATA 0xffd01418 0x00000000
+DATA 0xffd0141c 0x00000632
+DATA 0xffd01420 0x00000040
+DATA 0xffd01424 0x0000f07f
+DATA 0xffd01500 0x00000000 # SDRAM CS[0] Base address at 0x00000000
+DATA 0xffd01504 0x07FFFFF1 # SDRAM CS[0] Size 128MiB
+DATA 0xffd01508 0x10000000
+DATA 0xffd0150c 0x00FFFFF4 # SDRAM CS[1] Size, window disabled
+DATA 0xffd01514 0x00FFFFF8 # SDRAM CS[2] Size, window disabled
+DATA 0xffd0151c 0x00FFFFFC # SDRAM CS[3] Size, window disabled
+DATA 0xffd01494 0x00030000
+DATA 0xffd01498 0x00000000
+DATA 0xffd0149c 0x0000e803
+DATA 0xffd01480 0x00000001
+
+# End of Header extension
+DATA 0x0 0x0
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2010, 2018
+ * Allied Telesis <www.alliedtelesis.com>
+ */
+
+#include <common.h>
+#include <linux/io.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <asm/arch/mpp.h>
+#include <asm/arch/gpio.h>
+
+/* Note: GPIO differences between specific boards
+ *
+ * We're trying to avoid having multiple build targets for all the Kirkwood
+ * based boards one area where things tend to differ is GPIO usage. For the
+ * most part the GPIOs driven by the bootloader are similar enough in function
+ * that there is no harm in driving them.
+ *
+ * XZ4 XS6 XS16 GS24A GT40 GP24A GT24A
+ * GPIO39 - INT(<) NC MUX_RST_N(>) NC POE_DIS_N(>) NC
+ */
+
+#define SBX81LIFKW_OE_LOW ~(BIT(31) | BIT(30) | BIT(28) | BIT(27) | \
+ BIT(18) | BIT(17) | BIT(13) | BIT(12) | \
+ BIT(10))
+#define SBX81LIFKW_OE_HIGH ~(BIT(0) | BIT(1) | BIT(7))
+#define SBX81LIFKW_OE_VAL_LOW (BIT(31) | BIT(30) | BIT(28) | BIT(27))
+#define SBX81LIFKW_OE_VAL_HIGH (BIT(0) | BIT(1))
+
+#define MV88E6097_RESET 27
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct led {
+ u32 reg;
+ u32 value;
+ u32 mask;
+};
+
+struct led amber_solid = {
+ MVEBU_GPIO0_BASE,
+ BIT(10),
+ BIT(18) | BIT(10)
+};
+
+struct led green_solid = {
+ MVEBU_GPIO0_BASE,
+ BIT(18) | BIT(10),
+ BIT(18) | BIT(10)
+};
+
+struct led amber_flash = {
+ MVEBU_GPIO0_BASE,
+ 0,
+ BIT(18) | BIT(10)
+};
+
+struct led green_flash = {
+ MVEBU_GPIO0_BASE,
+ BIT(18),
+ BIT(18) | BIT(10)
+};
+
+static void status_led_set(struct led *led)
+{
+ clrsetbits_le32(led->reg, led->mask, led->value);
+}
+
+int board_early_init_f(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ mvebu_config_gpio(SBX81LIFKW_OE_VAL_LOW,
+ SBX81LIFKW_OE_VAL_HIGH,
+ SBX81LIFKW_OE_LOW, SBX81LIFKW_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ static const u32 kwmpp_config[] = {
+ MPP0_SPI_SCn,
+ MPP1_SPI_MOSI,
+ MPP2_SPI_SCK,
+ MPP3_SPI_MISO,
+ MPP4_UART0_RXD,
+ MPP5_UART0_TXD,
+ MPP6_SYSRST_OUTn,
+ MPP7_PEX_RST_OUTn,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_GPO,
+ MPP11_GPIO,
+ MPP12_GPO,
+ MPP13_GPIO,
+ MPP14_GPIO,
+ MPP15_UART0_RTS,
+ MPP16_UART0_CTS,
+ MPP17_GPIO,
+ MPP18_GPO,
+ MPP19_GPO,
+ MPP20_GPIO,
+ MPP21_GPIO,
+ MPP22_GPIO,
+ MPP23_GPIO,
+ MPP24_GPIO,
+ MPP25_GPIO,
+ MPP26_GPIO,
+ MPP27_GPIO,
+ MPP28_GPIO,
+ MPP29_GPIO,
+ MPP30_GPIO,
+ MPP31_GPIO,
+ MPP32_GPIO,
+ MPP33_GPIO,
+ MPP34_GPIO,
+ MPP35_GPIO,
+ MPP36_GPIO,
+ MPP37_GPIO,
+ MPP38_GPIO,
+ MPP39_GPIO,
+ MPP40_GPIO,
+ MPP41_GPIO,
+ MPP42_GPIO,
+ MPP43_GPIO,
+ MPP44_GPIO,
+ MPP45_GPIO,
+ MPP46_GPIO,
+ MPP47_GPIO,
+ MPP48_GPIO,
+ MPP49_GPIO,
+ 0
+ };
+
+ kirkwood_mpp_conf(kwmpp_config, NULL);
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Power-down unused subsystems. The required
+ * subsystems are:
+ *
+ * GE0 b0
+ * PEX0 PHY b1
+ * PEX0.0 b2
+ * TSU b5
+ * SDRAM b6
+ * RUNIT b7
+ */
+ writel((BIT(0) | BIT(1) | BIT(2) |
+ BIT(5) | BIT(6) | BIT(7)),
+ KW_CPU_REG_BASE + 0x1c);
+
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+ status_led_set(&amber_solid);
+
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* automatically defined by kirkwood config.h */
+void reset_phy(void)
+{
+}
+#endif
+
+#ifdef CONFIG_MV88E61XX_SWITCH
+int mv88e61xx_hw_reset(struct phy_device *phydev)
+{
+ /* Ensure the 88e6097 gets at least 10ms Reset
+ */
+ kw_gpio_set_value(MV88E6097_RESET, 0);
+ mdelay(20);
+ kw_gpio_set_value(MV88E6097_RESET, 1);
+ mdelay(20);
+
+ phydev->advertising = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full;
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+ status_led_set(&green_flash);
+
+ return 0;
+}
+#endif
#define BOARD_GPP_POL_LOW 0x0
#define BOARD_GPP_POL_MID 0x0
-/* IO expander on Marvell GP board includes e.g. fan enabling */
-struct marvell_io_exp {
- u8 chip;
- u8 addr;
- u8 val;
-};
-
-static struct marvell_io_exp io_exp[] = {
- { 0x20, 2, 0x40 }, /* Deassert both mini pcie reset signals */
- { 0x20, 6, 0xf9 },
- { 0x20, 2, 0x46 }, /* rst signals and ena USB3 current limiter */
- { 0x20, 6, 0xb9 },
- { 0x20, 3, 0x00 }, /* Set SFP_TX_DIS to zero */
- { 0x20, 7, 0xbf }, /* Drive SFP_TX_DIS to zero */
-};
-
static struct serdes_map board_serdes_map[] = {
{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
int board_init(void)
{
- int i;
-
/* Address of boot parameters */
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
setbits_le32(MVEBU_GPIO0_BASE + 0x0, BIT(19));
mdelay(10);
- /* Init I2C IO expanders */
- for (i = 0; i < ARRAY_SIZE(io_exp); i++)
- i2c_write(io_exp[i].chip, io_exp[i].addr, 1, &io_exp[i].val, 1);
-
return 0;
}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_KIRKWOOD=y
+CONFIG_SYS_TEXT_BASE=0x00600000
+CONFIG_TARGET_SBx81LIFKW=y
+CONFIG_IDENT_STRING="\nSBx81LIFKW"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-atl-sbx81lifkw"
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_BOOTDELAY=3
+CONFIG_SILENT_CONSOLE=y
+CONFIG_SILENT_U_BOOT_ONLY=y
+CONFIG_HUSH_PARSER=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_DHCP=y
+CONFIG_BOOTP_NTPSERVER=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_SNTP=y
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_DM=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+# CONFIG_MMC is not set
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHYLIB=y
+CONFIG_MV88E61XX_SWITCH=y
+CONFIG_MV88E61XX_CPU_PORT=10
+CONFIG_MV88E61XX_PHY_PORTS=0x003
+CONFIG_MV88E61XX_FIXED_PORTS=0x300
+CONFIG_SPI=y
+CONFIG_KIRKWOOD_SPI=y
CONFIG_ARM=y
CONFIG_ARCH_MVEBU=y
CONFIG_SYS_TEXT_BASE=0x00800000
+CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x141
CONFIG_SPL_I2C_SUPPORT=y
# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_PCI=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_SCSI_AHCI=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_SDMA=y
CONFIG_MMC_SDHCI_MV=y
CONFIG_PHY_GIGE=y
CONFIG_MVNETA=y
CONFIG_PCI=y
+CONFIG_SCSI=y
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_SYS_NS16550=y
CONFIG_KIRKWOOD_SPI=y
CONFIG_TARGET_LSXL=y
CONFIG_IDENT_STRING=" LS-CHLv2"
CONFIG_DEFAULT_DEVICE_TREE="kirkwood-lschlv2"
+CONFIG_DISTRO_DEFAULTS=y
CONFIG_SYS_EXTRA_OPTIONS="LSCHLV2"
+CONFIG_API=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/sda2"
+CONFIG_BOOTCOMMAND="run bootcmd_${bootsource}"
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
CONFIG_SYS_CONSOLE_INFO_QUIET=y
-CONFIG_SUPPORT_RAW_INITRD=y
# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_IDE=y
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_ISO_PARTITION=y
-CONFIG_EFI_PARTITION=y
-# CONFIG_PARTITION_UUIDS is not set
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_NETDEVICES=y
CONFIG_MVGBE=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
+CONFIG_DM_SPI=y
CONFIG_KIRKWOOD_SPI=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_NETDEVICES=y
CONFIG_MVGBE=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
+CONFIG_DM_SPI=y
CONFIG_KIRKWOOD_SPI=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_LZMA=y
+CONFIG_SYS_THUMB_BUILD=y
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
+ */
+
+#ifndef _CONFIG_SBX81LIFKW_H
+#define _CONFIG_SBX81LIFKW_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
+#define CONFIG_BUILD_TARGET "u-boot.kwb"
+
+/* additions for new ARM relocation support */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_GPIO 1
+
+#define CONFIG_MISC_INIT_R /* call misc_init_r */
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
+#define MTDPARTS_MTDOOPS "errlog"
+#define CONFIG_DOS_PARTITION
+
+/*
+ * Environment variables configurations
+ */
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */
+#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */
+#define CONFIG_ENV_SIZE 0x02000
+#define CONFIG_ENV_OFFSET 0xc0000 /* env starts here - 768K */
+
+/*
+ * U-Boot bootcode configuration
+ */
+
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
+#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
+
+/* size in bytes reserved for initial data */
+
+#include <asm/arch/config.h>
+/* There is no PHY directly connected so don't ask it for link status */
+#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi over miiphy interface */
+#define CONFIG_MVGBE /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable a single port */
+#define CONFIG_PHY_BASE_ADR 0x01
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * Time settings
+ */
+#define CONFIG_RTC_MV
+
+#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
+
+#endif /* _CONFIG_SBX81LIFKW_H */
* Commands configuration
*/
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MVTWSI
-#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
-#define CONFIG_SYS_I2C_SLAVE 0x0
-#define CONFIG_SYS_I2C_SPEED 100000
-
/* SPI NOR flash default params, used by sf commands */
#define CONFIG_SF_DEFAULT_BUS 1
#define CONFIG_PCI_SCAN_SHOW
#endif
+/* SATA support */
+#ifdef CONFIG_SCSI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+#endif
+
/* Keep device tree and initrd in lower memory so the kernel can access them */
#define RELOCATION_LIMITS_ENV_SETTINGS \
"fdt_high=0x10000000\0" \
*/
#define CONFIG_ENV_SIZE 0x20000 /* 128k */
#define CONFIG_ENV_OFFSET 0xE0000 /* env starts here */
+/*
+ * Environment is right behind U-Boot in flash. Make sure U-Boot
+ * doesn't grow into the environment area.
+ */
+#define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET
/*
* Default environment variables
#define CONFIG_ENV_SIZE 0x20000 /* 128k */
#define CONFIG_ENV_ADDR 0x80000
#define CONFIG_ENV_OFFSET 0x80000 /* env starts here */
+/*
+ * Environment is right behind U-Boot in flash. Make sure U-Boot
+ * doesn't grow into the environment area.
+ */
+#define CONFIG_BOARD_SIZE_LIMIT CONFIG_ENV_OFFSET
/*
* Default environment variables
projects / u-boot / commitdiff