Add initial support for the R8A7795 and R8A7796 based ULCB board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
help
Support for Renesas R-Car Gen3 platform
+config TARGET_ULCB
+ bool "ULCB board"
+ help
+ Support for Renesas R-Car Gen3 ULCB platform
+
endchoice
config SYS_SOC
default "rmobile"
source "board/renesas/salvator-x/Kconfig"
+source "board/renesas/ulcb/Kconfig"
endif
--- /dev/null
+if TARGET_ULCB
+
+config SYS_SOC
+ default "rmobile"
+
+config SYS_BOARD
+ default "ulcb"
+
+config SYS_VENDOR
+ default "renesas"
+
+config SYS_CONFIG_NAME
+ default "ulcb"
+
+endif
--- /dev/null
+ULCB BOARD
+M: Marek Vasut <marek.vasut+renesas@gmail.com>
+S: Maintained
+F: board/renesas/ulcb/
+F: include/configs/ulcb.h
+F: configs/r8a7795_ulcb_defconfig
+F: configs/r8a7796_ulcb_defconfig
--- /dev/null
+#
+# board/renesas/ulcb/Makefile
+#
+# Copyright (C) 2017 Renesas Electronics Corporation
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := ulcb.o cpld.o ../rcar-common/common.o
--- /dev/null
+/*
+ * ULCB board CPLD access support
+ *
+ * Copyright (C) 2017 Renesas Electronics Corporation
+ * Copyright (C) 2017 Cogent Embedded, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <spi.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+
+#define SCLK GPIO_GP_6_8
+#define SSTBZ GPIO_GP_2_3
+#define MOSI GPIO_GP_6_7
+#define MISO GPIO_GP_6_10
+
+#define CPLD_ADDR_MODE 0x00 /* RW */
+#define CPLD_ADDR_MUX 0x02 /* RW */
+#define CPLD_ADDR_DIPSW6 0x08 /* R */
+#define CPLD_ADDR_RESET 0x80 /* RW */
+#define CPLD_ADDR_VERSION 0xFF /* R */
+
+static int cpld_initialized;
+
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+ /* Always valid */
+ return 1;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+ /* Always active */
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+ /* Always active */
+}
+
+void ulcb_softspi_sda(int set)
+{
+ gpio_set_value(MOSI, set);
+}
+
+void ulcb_softspi_scl(int set)
+{
+ gpio_set_value(SCLK, set);
+}
+
+unsigned char ulcb_softspi_read(void)
+{
+ return !!gpio_get_value(MISO);
+}
+
+static void cpld_rw(u8 write)
+{
+ gpio_set_value(MOSI, write);
+ gpio_set_value(SSTBZ, 0);
+ gpio_set_value(SCLK, 1);
+ gpio_set_value(SCLK, 0);
+ gpio_set_value(SSTBZ, 1);
+}
+
+static u32 cpld_read(u8 addr)
+{
+ u32 data = 0;
+
+ spi_xfer(NULL, 8, &addr, NULL, SPI_XFER_BEGIN | SPI_XFER_END);
+
+ cpld_rw(0);
+
+ spi_xfer(NULL, 32, NULL, &data, SPI_XFER_BEGIN | SPI_XFER_END);
+
+ return swab32(data);
+}
+
+static void cpld_write(u8 addr, u32 data)
+{
+ data = swab32(data);
+
+ spi_xfer(NULL, 32, &data, NULL, SPI_XFER_BEGIN | SPI_XFER_END);
+
+ spi_xfer(NULL, 8, NULL, &addr, SPI_XFER_BEGIN | SPI_XFER_END);
+
+ cpld_rw(1);
+}
+
+static void cpld_init(void)
+{
+ if (cpld_initialized)
+ return;
+
+ /* PULL-UP on MISO line */
+ setbits_le32(PFC_PUEN5, PUEN_SSI_SDATA4);
+
+ gpio_request(SCLK, NULL);
+ gpio_request(SSTBZ, NULL);
+ gpio_request(MOSI, NULL);
+ gpio_request(MISO, NULL);
+
+ gpio_direction_output(SCLK, 0);
+ gpio_direction_output(SSTBZ, 1);
+ gpio_direction_output(MOSI, 0);
+ gpio_direction_input(MISO);
+
+ /* Dummy read */
+ cpld_read(CPLD_ADDR_VERSION);
+
+ cpld_initialized = 1;
+}
+
+static int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ u32 addr, val;
+
+ cpld_init();
+
+ if (argc == 2 && strcmp(argv[1], "info") == 0) {
+ printf("CPLD version:\t\t\t0x%08x\n",
+ cpld_read(CPLD_ADDR_VERSION));
+ printf("H3 Mode setting (MD0..28):\t0x%08x\n",
+ cpld_read(CPLD_ADDR_MODE));
+ printf("Multiplexer settings:\t\t0x%08x\n",
+ cpld_read(CPLD_ADDR_MUX));
+ printf("DIPSW (SW6):\t\t\t0x%08x\n",
+ cpld_read(CPLD_ADDR_DIPSW6));
+ return 0;
+ }
+
+ if (argc < 3)
+ return CMD_RET_USAGE;
+
+ addr = simple_strtoul(argv[2], NULL, 16);
+ if (!(addr == CPLD_ADDR_VERSION || addr == CPLD_ADDR_MODE ||
+ addr == CPLD_ADDR_MUX || addr == CPLD_ADDR_DIPSW6 ||
+ addr == CPLD_ADDR_RESET)) {
+ printf("Invalid CPLD register address\n");
+ return CMD_RET_USAGE;
+ }
+
+ if (argc == 3 && strcmp(argv[1], "read") == 0) {
+ printf("0x%x\n", cpld_read(addr));
+ } else if (argc == 4 && strcmp(argv[1], "write") == 0) {
+ val = simple_strtoul(argv[3], NULL, 16);
+ cpld_write(addr, val);
+ }
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ cpld, 4, 1, do_cpld,
+ "CPLD access",
+ "info\n"
+ "cpld read addr\n"
+ "cpld write addr val\n"
+);
+
+void reset_cpu(ulong addr)
+{
+ cpld_init();
+ cpld_write(CPLD_ADDR_RESET, 1);
+}
--- /dev/null
+/*
+ * board/renesas/ulcb/ulcb.c
+ * This file is ULCB board support.
+ *
+ * Copyright (C) 2017 Renesas Electronics Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <netdev.h>
+#include <dm.h>
+#include <dm/platform_data/serial_sh.h>
+#include <asm/processor.h>
+#include <asm/mach-types.h>
+#include <asm/io.h>
+#include <linux/errno.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/rmobile.h>
+#include <asm/arch/rcar-mstp.h>
+#include <asm/arch/sh_sdhi.h>
+#include <i2c.h>
+#include <mmc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define CPGWPCR 0xE6150904
+#define CPGWPR 0xE615090C
+
+#define CLK2MHZ(clk) (clk / 1000 / 1000)
+void s_init(void)
+{
+ struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE;
+ struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE;
+
+ /* Watchdog init */
+ writel(0xA5A5A500, &rwdt->rwtcsra);
+ writel(0xA5A5A500, &swdt->swtcsra);
+
+ writel(0xA5A50000, CPGWPCR);
+ writel(0xFFFFFFFF, CPGWPR);
+}
+
+#define GSX_MSTP112 BIT(12) /* 3DG */
+#define TMU0_MSTP125 BIT(25) /* secure */
+#define TMU1_MSTP124 BIT(24) /* non-secure */
+#define SCIF2_MSTP310 BIT(10) /* SCIF2 */
+#define ETHERAVB_MSTP812 BIT(12)
+#define DVFS_MSTP926 BIT(26)
+#define SD0_MSTP314 BIT(14)
+#define SD1_MSTP313 BIT(13)
+#define SD2_MSTP312 BIT(12) /* either MMC0 */
+
+#define SD0CKCR 0xE6150074
+#define SD1CKCR 0xE6150078
+#define SD2CKCR 0xE6150268
+#define SD3CKCR 0xE615026C
+
+int board_early_init_f(void)
+{
+ /* TMU0,1 */ /* which use ? */
+ mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125 | TMU1_MSTP124);
+ /* SCIF2 */
+ mstp_clrbits_le32(MSTPSR3, SMSTPCR3, SCIF2_MSTP310);
+ /* EHTERAVB */
+ mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHERAVB_MSTP812);
+ /* eMMC */
+ mstp_clrbits_le32(MSTPSR3, SMSTPCR3, SD1_MSTP313 | SD2_MSTP312);
+ /* SDHI0 */
+ mstp_clrbits_le32(MSTPSR3, SMSTPCR3, SD0_MSTP314);
+
+ writel(0, SD0CKCR);
+ writel(0, SD1CKCR);
+ writel(0, SD2CKCR);
+ writel(0, SD3CKCR);
+
+#if defined(CONFIG_SYS_I2C) && defined(CONFIG_SYS_I2C_SH)
+ /* DVFS for reset */
+ mstp_clrbits_le32(MSTPSR9, SMSTPCR9, DVFS_MSTP926);
+#endif
+ return 0;
+}
+
+/* SYSC */
+/* R/- 32 Power status register 2(3DG) */
+#define SYSC_PWRSR2 0xE6180100
+/* -/W 32 Power resume control register 2 (3DG) */
+#define SYSC_PWRONCR2 0xE618010C
+
+int board_init(void)
+{
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_TEXT_BASE + 0x50000;
+
+ /* Init PFC controller */
+#if defined(CONFIG_R8A7795)
+ r8a7795_pinmux_init();
+#elif defined(CONFIG_R8A7796)
+ r8a7796_pinmux_init();
+#endif
+
+ /* USB1 pull-up */
+ setbits_le32(PFC_PUEN6, PUEN_USB1_OVC | PUEN_USB1_PWEN);
+
+#ifdef CONFIG_RAVB
+ /* EtherAVB Enable */
+ /* GPSR2 */
+ gpio_request(GPIO_GFN_AVB_AVTP_CAPTURE_A, NULL);
+ gpio_request(GPIO_GFN_AVB_AVTP_MATCH_A, NULL);
+ gpio_request(GPIO_GFN_AVB_LINK, NULL);
+ gpio_request(GPIO_GFN_AVB_PHY_INT, NULL);
+ gpio_request(GPIO_GFN_AVB_MAGIC, NULL);
+ gpio_request(GPIO_GFN_AVB_MDC, NULL);
+
+ /* IPSR0 */
+ gpio_request(GPIO_IFN_AVB_MDC, NULL);
+ gpio_request(GPIO_IFN_AVB_MAGIC, NULL);
+ gpio_request(GPIO_IFN_AVB_PHY_INT, NULL);
+ gpio_request(GPIO_IFN_AVB_LINK, NULL);
+ gpio_request(GPIO_IFN_AVB_AVTP_MATCH_A, NULL);
+ gpio_request(GPIO_IFN_AVB_AVTP_CAPTURE_A, NULL);
+ /* IPSR1 */
+ gpio_request(GPIO_FN_AVB_AVTP_PPS, NULL);
+ /* IPSR2 */
+ gpio_request(GPIO_FN_AVB_AVTP_MATCH_B, NULL);
+ /* IPSR3 */
+ gpio_request(GPIO_FN_AVB_AVTP_CAPTURE_B, NULL);
+
+ /* AVB_PHY_RST */
+ gpio_request(GPIO_GP_2_10, NULL);
+ gpio_direction_output(GPIO_GP_2_10, 0);
+ mdelay(20);
+ gpio_set_value(GPIO_GP_2_10, 1);
+ udelay(1);
+#endif
+
+ return 0;
+}
+
+static struct eth_pdata salvator_x_ravb_platdata = {
+ .iobase = 0xE6800000,
+ .phy_interface = 0,
+ .max_speed = 1000,
+};
+
+U_BOOT_DEVICE(salvator_x_ravb) = {
+ .name = "ravb",
+ .platdata = &salvator_x_ravb_platdata,
+};
+
+#ifdef CONFIG_SH_SDHI
+int board_mmc_init(bd_t *bis)
+{
+ int ret = -ENODEV;
+
+ /* SDHI0 */
+ gpio_request(GPIO_GFN_SD0_DAT0, NULL);
+ gpio_request(GPIO_GFN_SD0_DAT1, NULL);
+ gpio_request(GPIO_GFN_SD0_DAT2, NULL);
+ gpio_request(GPIO_GFN_SD0_DAT3, NULL);
+ gpio_request(GPIO_GFN_SD0_CLK, NULL);
+ gpio_request(GPIO_GFN_SD0_CMD, NULL);
+ gpio_request(GPIO_GFN_SD0_CD, NULL);
+ gpio_request(GPIO_GFN_SD0_WP, NULL);
+
+ gpio_request(GPIO_GP_5_2, NULL);
+ gpio_request(GPIO_GP_5_1, NULL);
+ gpio_direction_output(GPIO_GP_5_2, 1); /* power on */
+ gpio_direction_output(GPIO_GP_5_1, 1); /* 1: 3.3V, 0: 1.8V */
+
+ ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI0_BASE, 0,
+ SH_SDHI_QUIRK_64BIT_BUF);
+ if (ret)
+ return ret;
+
+ /* SDHI1/SDHI2 eMMC */
+ gpio_request(GPIO_GFN_SD1_DAT0, NULL);
+ gpio_request(GPIO_GFN_SD1_DAT1, NULL);
+ gpio_request(GPIO_GFN_SD1_DAT2, NULL);
+ gpio_request(GPIO_GFN_SD1_DAT3, NULL);
+ gpio_request(GPIO_GFN_SD2_DAT0, NULL);
+ gpio_request(GPIO_GFN_SD2_DAT1, NULL);
+ gpio_request(GPIO_GFN_SD2_DAT2, NULL);
+ gpio_request(GPIO_GFN_SD2_DAT3, NULL);
+ gpio_request(GPIO_GFN_SD2_CLK, NULL);
+#if defined(CONFIG_R8A7795)
+ gpio_request(GPIO_GFN_SD2_CMD, NULL);
+#elif defined(CONFIG_R8A7796)
+ gpio_request(GPIO_FN_SD2_CMD, NULL);
+#else
+#error Only R8A7795 and R87796 is supported
+#endif
+ gpio_request(GPIO_GP_5_3, NULL);
+ gpio_request(GPIO_GP_5_9, NULL);
+ gpio_direction_output(GPIO_GP_5_3, 0); /* 1: 3.3V, 0: 1.8V */
+ gpio_direction_output(GPIO_GP_5_9, 0); /* 1: 3.3V, 0: 1.8V */
+
+ ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI2_BASE, 1,
+ SH_SDHI_QUIRK_64BIT_BUF);
+
+ return ret;
+}
+#endif
+
+int dram_init(void)
+{
+ gd->ram_size = PHYS_SDRAM_1_SIZE;
+#if (CONFIG_NR_DRAM_BANKS >= 2)
+ gd->ram_size += PHYS_SDRAM_2_SIZE;
+#endif
+#if (CONFIG_NR_DRAM_BANKS >= 3)
+ gd->ram_size += PHYS_SDRAM_3_SIZE;
+#endif
+#if (CONFIG_NR_DRAM_BANKS >= 4)
+ gd->ram_size += PHYS_SDRAM_4_SIZE;
+#endif
+
+ return 0;
+}
+
+int dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+#if (CONFIG_NR_DRAM_BANKS >= 2)
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+ gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+#endif
+#if (CONFIG_NR_DRAM_BANKS >= 3)
+ gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
+ gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
+#endif
+#if (CONFIG_NR_DRAM_BANKS >= 4)
+ gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
+ gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
+#endif
+ return 0;
+}
+
+const struct rmobile_sysinfo sysinfo = {
+ CONFIG_RCAR_BOARD_STRING
+};
+
+static const struct sh_serial_platdata serial_platdata = {
+ .base = SCIF2_BASE,
+ .type = PORT_SCIF,
+ .clk = CONFIG_SH_SCIF_CLK_FREQ,
+ .clk_mode = INT_CLK,
+};
+
+U_BOOT_DEVICE(salvator_x_scif2) = {
+ .name = "serial_sh",
+ .platdata = &serial_platdata,
+};
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_RMOBILE=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_RCAR_GEN3=y
+CONFIG_TARGET_ULCB=y
+CONFIG_DEFAULT_FDT_FILE="r8a7795-h3ulcb.dtb"
+CONFIG_VERSION_VARIABLE=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_SH_SDHI=y
+CONFIG_DM_ETH=y
+CONFIG_RENESAS_RAVB=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_OF_LIBFDT=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_RMOBILE=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_RCAR_GEN3=y
+CONFIG_R8A7796=y
+CONFIG_TARGET_ULCB=y
+CONFIG_DEFAULT_FDT_FILE="r8a7796-m3ulcb.dtb"
+CONFIG_VERSION_VARIABLE=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_SH_SDHI=y
+CONFIG_DM_ETH=y
+CONFIG_RENESAS_RAVB=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_OF_LIBFDT=y
--- /dev/null
+/*
+ * include/configs/ulcb.h
+ * This file is ULCB board configuration.
+ *
+ * Copyright (C) 2017 Renesas Electronics Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __ULCB_H
+#define __ULCB_H
+
+#undef DEBUG
+
+#define CONFIG_RCAR_BOARD_STRING "ULCB"
+
+#include "rcar-gen3-common.h"
+
+/* M3 ULCB has 2 banks, each with 1 GiB of RAM */
+#if defined(CONFIG_R8A7796)
+#undef PHYS_SDRAM_1_SIZE
+#undef PHYS_SDRAM_2_SIZE
+#define PHYS_SDRAM_1_SIZE (0x40000000u - DRAM_RSV_SIZE)
+#define PHYS_SDRAM_2_SIZE 0x40000000u
+#endif
+
+/* SCIF */
+#define CONFIG_SCIF_CONSOLE
+#define CONFIG_CONS_SCIF2
+#define CONFIG_CONS_INDEX 2
+#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_S3D4_CLK_FREQ
+
+/* [A] Hyper Flash */
+/* use to RPC(SPI Multi I/O Bus Controller) */
+
+/* Ethernet RAVB */
+#define CONFIG_NET_MULTI
+#define CONFIG_PHY_MICREL
+#define CONFIG_BITBANGMII
+#define CONFIG_BITBANGMII_MULTI
+
+/* Board Clock */
+/* XTAL_CLK : 33.33MHz */
+#define RCAR_XTAL_CLK 33333333u
+#define CONFIG_SYS_CLK_FREQ RCAR_XTAL_CLK
+/* ch0to2 CPclk, ch3to11 S3D2_PEREclk, ch12to14 S3D2_RTclk */
+/* CPclk 16.66MHz, S3D2 133.33MHz , S3D4 66.66MHz */
+#define CONFIG_CP_CLK_FREQ (CONFIG_SYS_CLK_FREQ / 2)
+#define CONFIG_PLL1_CLK_FREQ (CONFIG_SYS_CLK_FREQ * 192 / 2)
+#define CONFIG_S3D2_CLK_FREQ (266666666u/2)
+#define CONFIG_S3D4_CLK_FREQ (266666666u/4)
+
+/* Generic Timer Definitions (use in assembler source) */
+#define COUNTER_FREQUENCY 0xFE502A /* 16.66MHz from CPclk */
+
+/* Generic Interrupt Controller Definitions */
+#define CONFIG_GICV2
+#define GICD_BASE 0xF1010000
+#define GICC_BASE 0xF1020000
+
+/* CPLD SPI */
+#define CONFIG_CMD_SPI
+#define CONFIG_SOFT_SPI
+#define SPI_DELAY udelay(0)
+#define SPI_SDA(val) ulcb_softspi_sda(val)
+#define SPI_SCL(val) ulcb_softspi_scl(val)
+#define SPI_READ ulcb_softspi_read()
+#ifndef __ASSEMBLY__
+void ulcb_softspi_sda(int);
+void ulcb_softspi_scl(int);
+unsigned char ulcb_softspi_read(void);
+#endif
+
+/* i2c */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SH
+#define CONFIG_SYS_I2C_SLAVE 0x60
+#define CONFIG_SYS_I2C_SH_NUM_CONTROLLERS 1
+#define CONFIG_SYS_I2C_SH_SPEED0 400000
+#define CONFIG_SH_I2C_DATA_HIGH 4
+#define CONFIG_SH_I2C_DATA_LOW 5
+#define CONFIG_SH_I2C_CLOCK 10000000
+
+#define CONFIG_SYS_I2C_POWERIC_ADDR 0x30
+
+/* USB */
+#ifdef CONFIG_R8A7795
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
+#else
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#endif
+
+/* SDHI */
+#define CONFIG_SH_SDHI_FREQ 200000000
+
+/* Environment in eMMC, at the end of 2nd "boot sector" */
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET (-CONFIG_ENV_SIZE)
+#define CONFIG_SYS_MMC_ENV_DEV 1
+#define CONFIG_SYS_MMC_ENV_PART 2
+
+/* Module stop status bits */
+/* MFIS, SCIF1 */
+#define CONFIG_SMSTP2_ENA 0x00002040
+/* SCIF2 */
+#define CONFIG_SMSTP3_ENA 0x00000400
+/* INTC-AP, IRQC */
+#define CONFIG_SMSTP4_ENA 0x00000180
+
+#endif /* __ULCB_H */
projects / u-boot / commitdiff