config FIT
bool "Support Flattened Image Tree"
+ select MD5
help
This option allows you to boot the new uImage structure,
Flattened Image Tree. FIT is formally a FDT, which can include
select SPL_SEPARATE_BSS if SPL
select DM_USB if USB
select BLK
+ select CLK
+ select SPL_CLK
+ select CLK_ZYNQ
config ARCH_ZYNQMP
bool "Support Xilinx ZynqMP Platform"
return !(addr & (align - 1)) && !(size & (align - 1));
}
-static u64 set_one_region(u64 start, u64 size, u64 attrs, int level)
+/* Use flag to indicate if attrs has more than d-cache attributes */
+static u64 set_one_region(u64 start, u64 size, u64 attrs, bool flag, int level)
{
int levelshift = level2shift(level);
u64 levelsize = 1ULL << levelshift;
/* Can we can just modify the current level block PTE? */
if (is_aligned(start, size, levelsize)) {
- *pte &= ~PMD_ATTRINDX_MASK;
- *pte |= attrs;
+ if (flag) {
+ *pte &= ~PMD_ATTRMASK;
+ *pte |= attrs & PMD_ATTRMASK;
+ } else {
+ *pte &= ~PMD_ATTRINDX_MASK;
+ *pte |= attrs & PMD_ATTRINDX_MASK;
+ }
debug("Set attrs=%llx pte=%p level=%d\n", attrs, pte, level);
return levelsize;
u64 r;
for (level = 1; level < 4; level++) {
- r = set_one_region(start, size, attrs, level);
+ /* Set d-cache attributes only */
+ r = set_one_region(start, size, attrs, false, level);
if (r) {
/* PTE successfully replaced */
size -= r;
flush_dcache_range(real_start, real_start + real_size);
}
+/*
+ * Modify MMU table for a region with updated PXN/UXN/Memory type/valid bits.
+ * The procecess is break-before-make. The target region will be marked as
+ * invalid during the process of changing.
+ */
+void mmu_change_region_attr(phys_addr_t addr, size_t siz, u64 attrs)
+{
+ int level;
+ u64 r, size, start;
+
+ start = addr;
+ size = siz;
+ /*
+ * Loop through the address range until we find a page granule that fits
+ * our alignment constraints, then set it to "invalid".
+ */
+ while (size > 0) {
+ for (level = 1; level < 4; level++) {
+ /* Set PTE to fault */
+ r = set_one_region(start, size, PTE_TYPE_FAULT, true,
+ level);
+ if (r) {
+ /* PTE successfully invalidated */
+ size -= r;
+ start += r;
+ break;
+ }
+ }
+ }
+
+ flush_dcache_range(gd->arch.tlb_addr,
+ gd->arch.tlb_addr + gd->arch.tlb_size);
+ __asm_invalidate_tlb_all();
+
+ /*
+ * Loop through the address range until we find a page granule that fits
+ * our alignment constraints, then set it to the new cache attributes
+ */
+ start = addr;
+ size = siz;
+ while (size > 0) {
+ for (level = 1; level < 4; level++) {
+ /* Set PTE to new attributes */
+ r = set_one_region(start, size, attrs, true, level);
+ if (r) {
+ /* PTE successfully updated */
+ size -= r;
+ start += r;
+ break;
+ }
+ }
+ }
+ flush_dcache_range(gd->arch.tlb_addr,
+ gd->arch.tlb_addr + gd->arch.tlb_size);
+ __asm_invalidate_tlb_all();
+}
+
#else /* CONFIG_SYS_DCACHE_OFF */
/*
select SYS_FSL_SRDS_1
select SYS_HAS_SERDES
+config FSL_MC_ENET
+ bool "Management Complex network"
+ depends on ARCH_LS2080A
+ default y
+ select RESV_RAM
+ help
+ Enable Management Complex (MC) network
+
menu "Layerscape architecture"
depends on FSL_LSCH2 || FSL_LSCH3
clock, in another word SDHC_clk = Platform_clk / this_divider.
endmenu
+config RESV_RAM
+ bool
+ help
+ Reserve memory from the top, tracked by gd->arch.resv_ram. This
+ reserved RAM can be used by special driver that resides in memory
+ after U-Boot exits. It's up to implementation to allocate and allow
+ access to this reserved memory. For example, the reserved RAM can
+ be at the high end of physical memory. The reserve RAM may be
+ excluded from memory bank(s) passed to OS, or marked as reserved.
+
config SYS_FSL_ERRATUM_A008336
bool
config SYS_FSL_ERRATUM_A009929
bool
+
+config SYS_MC_RSV_MEM_ALIGN
+ hex "Management Complex reserved memory alignment"
+ depends on RESV_RAM
+ default 0x20000000
+ help
+ Reserved memory needs to be aligned for MC to use. Default value
+ is 512MB.
{
u64 tlb_addr_save = gd->arch.tlb_addr;
unsigned int el = current_el();
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
int index;
-#endif
mem_map = final_map;
+ /* Update mapping for DDR to actual size */
+ for (index = 0; index < ARRAY_SIZE(final_map) - 2; index++) {
+ /*
+ * Find the entry for DDR mapping and update the address and
+ * size. Zero-sized mapping will be skipped when creating MMU
+ * table.
+ */
+ switch (final_map[index].virt) {
+ case CONFIG_SYS_FSL_DRAM_BASE1:
+ final_map[index].virt = gd->bd->bi_dram[0].start;
+ final_map[index].phys = gd->bd->bi_dram[0].start;
+ final_map[index].size = gd->bd->bi_dram[0].size;
+ break;
+#ifdef CONFIG_SYS_FSL_DRAM_BASE2
+ case CONFIG_SYS_FSL_DRAM_BASE2:
+#if (CONFIG_NR_DRAM_BANKS >= 2)
+ final_map[index].virt = gd->bd->bi_dram[1].start;
+ final_map[index].phys = gd->bd->bi_dram[1].start;
+ final_map[index].size = gd->bd->bi_dram[1].size;
+#else
+ final_map[index].size = 0;
+#endif
+ break;
+#endif
+#ifdef CONFIG_SYS_FSL_DRAM_BASE3
+ case CONFIG_SYS_FSL_DRAM_BASE3:
+#if (CONFIG_NR_DRAM_BANKS >= 3)
+ final_map[index].virt = gd->bd->bi_dram[2].start;
+ final_map[index].phys = gd->bd->bi_dram[2].start;
+ final_map[index].size = gd->bd->bi_dram[2].size;
+#else
+ final_map[index].size = 0;
+#endif
+ break;
+#endif
+ default:
+ break;
+ }
+ }
+
#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
if (gd->arch.secure_ram & MEM_RESERVE_SECURE_MAINTAINED) {
if (el == 3) {
setup_pgtables();
gd->arch.tlb_addr = tlb_addr_save;
- /* flush new MMU table */
- flush_dcache_range(gd->arch.tlb_addr,
- gd->arch.tlb_addr + gd->arch.tlb_size);
+ /* Disable cache and MMU */
+ dcache_disable(); /* TLBs are invalidated */
+ invalidate_icache_all();
/* point TTBR to the new table */
set_ttbr_tcr_mair(el, gd->arch.tlb_addr, get_tcr(el, NULL, NULL),
MEMORY_ATTRIBUTES);
- /*
- * EL3 MMU is already enabled, just need to invalidate TLB to load the
- * new table. The new table is compatible with the current table, if
- * MMU somehow walks through the new table before invalidation TLB,
- * it still works. So we don't need to turn off MMU here.
- * When EL2 MMU table is created by calling this function, MMU needs
- * to be enabled.
- */
+
set_sctlr(get_sctlr() | CR_M);
}
{
phys_size_t ram_top = ram_size;
-#ifdef CONFIG_SYS_MEM_TOP_HIDE
-#error CONFIG_SYS_MEM_TOP_HIDE not to be used together with this function
-#endif
-
-/* Carve the MC private DRAM block from the end of DRAM */
#ifdef CONFIG_FSL_MC_ENET
+ /* The start address of MC reserved memory needs to be aligned. */
ram_top -= mc_get_dram_block_size();
ram_top &= ~(CONFIG_SYS_MC_RSV_MEM_ALIGN - 1);
#endif
- return ram_top;
+ return ram_size - ram_top;
+}
+
+phys_size_t get_effective_memsize(void)
+{
+ phys_size_t ea_size, rem = 0;
+
+ /*
+ * For ARMv8 SoCs, DDR memory is split into two or three regions. The
+ * first region is 2GB space at 0x8000_0000. If the memory extends to
+ * the second region (or the third region if applicable), the secure
+ * memory and Management Complex (MC) memory should be put into the
+ * highest region, i.e. the end of DDR memory. CONFIG_MAX_MEM_MAPPED
+ * is set to the size of first region so U-Boot doesn't relocate itself
+ * into higher address. Should DDR be configured to skip the first
+ * region, this function needs to be adjusted.
+ */
+ if (gd->ram_size > CONFIG_MAX_MEM_MAPPED) {
+ ea_size = CONFIG_MAX_MEM_MAPPED;
+ rem = gd->ram_size - ea_size;
+ } else {
+ ea_size = gd->ram_size;
+ }
+
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+ /* Check if we have enough space for secure memory */
+ if (rem > CONFIG_SYS_MEM_RESERVE_SECURE) {
+ rem -= CONFIG_SYS_MEM_RESERVE_SECURE;
+ } else {
+ if (ea_size > CONFIG_SYS_MEM_RESERVE_SECURE) {
+ ea_size -= CONFIG_SYS_MEM_RESERVE_SECURE;
+ rem = 0; /* Presume MC requires more memory */
+ } else {
+ printf("Error: No enough space for secure memory.\n");
+ }
+ }
+#endif
+ /* Check if we have enough memory for MC */
+ if (rem < board_reserve_ram_top(rem)) {
+ /* Not enough memory in high region to reserve */
+ if (ea_size > board_reserve_ram_top(rem))
+ ea_size -= board_reserve_ram_top(rem);
+ else
+ printf("Error: No enough space for reserved memory.\n");
+ }
+
+ return ea_size;
+}
+
+void dram_init_banksize(void)
+{
+#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
+ phys_size_t dp_ddr_size;
+#endif
+
+ /*
+ * gd->ram_size has the total size of DDR memory, less reserved secure
+ * memory. The DDR extends from low region to high region(s) presuming
+ * no hole is created with DDR configuration. gd->arch.secure_ram tracks
+ * the location of secure memory. gd->arch.resv_ram tracks the location
+ * of reserved memory for Management Complex (MC).
+ */
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
+ gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
+ gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
+ gd->bd->bi_dram[1].size = gd->ram_size -
+ CONFIG_SYS_DDR_BLOCK1_SIZE;
+#ifdef CONFIG_SYS_DDR_BLOCK3_BASE
+ if (gd->bi_dram[1].size > CONFIG_SYS_DDR_BLOCK2_SIZE) {
+ gd->bd->bi_dram[2].start = CONFIG_SYS_DDR_BLOCK3_BASE;
+ gd->bd->bi_dram[2].size = gd->bd->bi_dram[1].size -
+ CONFIG_SYS_DDR_BLOCK2_SIZE;
+ gd->bd->bi_dram[1].size = CONFIG_SYS_DDR_BLOCK2_SIZE;
+ }
+#endif
+ } else {
+ gd->bd->bi_dram[0].size = gd->ram_size;
+ }
+#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
+#ifdef CONFIG_SYS_DDR_BLOCK3_BASE
+ if (gd->bd->bi_dram[2].size >= CONFIG_SYS_MEM_RESERVE_SECURE) {
+ gd->bd->bi_dram[2].size -= CONFIG_SYS_MEM_RESERVE_SECURE;
+ gd->arch.secure_ram = gd->bd->bi_dram[2].start +
+ gd->bd->bi_dram[2].size;
+ gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+ gd->ram_size -= CONFIG_SYS_MEM_RESERVE_SECURE;
+ } else
+#endif
+ {
+ if (gd->bd->bi_dram[1].size >= CONFIG_SYS_MEM_RESERVE_SECURE) {
+ gd->bd->bi_dram[1].size -=
+ CONFIG_SYS_MEM_RESERVE_SECURE;
+ gd->arch.secure_ram = gd->bd->bi_dram[1].start +
+ gd->bd->bi_dram[1].size;
+ gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+ gd->ram_size -= CONFIG_SYS_MEM_RESERVE_SECURE;
+ } else if (gd->bd->bi_dram[0].size >
+ CONFIG_SYS_MEM_RESERVE_SECURE) {
+ gd->bd->bi_dram[0].size -=
+ CONFIG_SYS_MEM_RESERVE_SECURE;
+ gd->arch.secure_ram = gd->bd->bi_dram[0].start +
+ gd->bd->bi_dram[0].size;
+ gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
+ gd->ram_size -= CONFIG_SYS_MEM_RESERVE_SECURE;
+ }
+ }
+#endif /* CONFIG_SYS_MEM_RESERVE_SECURE */
+
+#ifdef CONFIG_FSL_MC_ENET
+ /* Assign memory for MC */
+#ifdef CONFIG_SYS_DDR_BLOCK3_BASE
+ if (gd->bd->bi_dram[2].size >=
+ board_reserve_ram_top(gd->bd->bi_dram[2].size)) {
+ gd->arch.resv_ram = gd->bd->bi_dram[2].start +
+ gd->bd->bi_dram[2].size -
+ board_reserve_ram_top(gd->bd->bi_dram[2].size);
+ } else
+#endif
+ {
+ if (gd->bd->bi_dram[1].size >=
+ board_reserve_ram_top(gd->bd->bi_dram[1].size)) {
+ gd->arch.resv_ram = gd->bd->bi_dram[1].start +
+ gd->bd->bi_dram[1].size -
+ board_reserve_ram_top(gd->bd->bi_dram[1].size);
+ } else if (gd->bd->bi_dram[0].size >
+ board_reserve_ram_top(gd->bd->bi_dram[0].size)) {
+ gd->arch.resv_ram = gd->bd->bi_dram[0].start +
+ gd->bd->bi_dram[0].size -
+ board_reserve_ram_top(gd->bd->bi_dram[0].size);
+ }
+ }
+#endif /* CONFIG_FSL_MC_ENET */
+
+#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
+#ifdef CONFIG_SYS_DDR_BLOCK3_BASE
+#error "This SoC shouldn't have DP DDR"
+#endif
+ if (soc_has_dp_ddr()) {
+ /* initialize DP-DDR here */
+ puts("DP-DDR: ");
+ /*
+ * DDR controller use 0 as the base address for binding.
+ * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
+ */
+ dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
+ CONFIG_DP_DDR_CTRL,
+ CONFIG_DP_DDR_NUM_CTRLS,
+ CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
+ NULL, NULL, NULL);
+ if (dp_ddr_size) {
+ gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
+ gd->bd->bi_dram[2].size = dp_ddr_size;
+ } else {
+ puts("Not detected");
+ }
+ }
+#endif
+}
+
+#if defined(CONFIG_EFI_LOADER) && !defined(CONFIG_SPL_BUILD)
+void efi_add_known_memory(void)
+{
+ int i;
+ phys_addr_t ram_start, start;
+ phys_size_t ram_size;
+ u64 pages;
+
+ /* Add RAM */
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
+#ifdef CONFIG_SYS_DDR_BLOCK3_BASE
+#error "This SoC shouldn't have DP DDR"
+#endif
+ if (i == 2)
+ continue; /* skip DP-DDR */
+#endif
+ ram_start = gd->bd->bi_dram[i].start;
+ ram_size = gd->bd->bi_dram[i].size;
+#ifdef CONFIG_RESV_RAM
+ if (gd->arch.resv_ram >= ram_start &&
+ gd->arch.resv_ram < ram_start + ram_size)
+ ram_size = gd->arch.resv_ram - ram_start;
+#endif
+ start = (ram_start + EFI_PAGE_MASK) & ~EFI_PAGE_MASK;
+ pages = (ram_size + EFI_PAGE_MASK) >> EFI_PAGE_SHIFT;
+
+ efi_add_memory_map(start, pages, EFI_CONVENTIONAL_MEMORY,
+ false);
+ }
+}
+#endif
+
+/*
+ * Before DDR size is known, early MMU table have DDR mapped as device memory
+ * to avoid speculative access. To relocate U-Boot to DDR, "normal memory"
+ * needs to be set for these mappings.
+ * If a special case configures DDR with holes in the mapping, the holes need
+ * to be marked as invalid. This is not implemented in this function.
+ */
+void update_early_mmu_table(void)
+{
+ if (!gd->arch.tlb_addr)
+ return;
+
+ if (gd->ram_size <= CONFIG_SYS_FSL_DRAM_SIZE1) {
+ mmu_change_region_attr(
+ CONFIG_SYS_SDRAM_BASE,
+ gd->ram_size,
+ PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_OUTER_SHARE |
+ PTE_BLOCK_NS |
+ PTE_TYPE_VALID);
+ } else {
+ mmu_change_region_attr(
+ CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_DDR_BLOCK1_SIZE,
+ PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_OUTER_SHARE |
+ PTE_BLOCK_NS |
+ PTE_TYPE_VALID);
+#ifdef CONFIG_SYS_DDR_BLOCK3_BASE
+#ifndef CONFIG_SYS_DDR_BLOCK2_SIZE
+#error "Missing CONFIG_SYS_DDR_BLOCK2_SIZE"
+#endif
+ if (gd->ram_size - CONFIG_SYS_DDR_BLOCK1_SIZE >
+ CONFIG_SYS_DDR_BLOCK2_SIZE) {
+ mmu_change_region_attr(
+ CONFIG_SYS_DDR_BLOCK2_BASE,
+ CONFIG_SYS_DDR_BLOCK2_SIZE,
+ PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_OUTER_SHARE |
+ PTE_BLOCK_NS |
+ PTE_TYPE_VALID);
+ mmu_change_region_attr(
+ CONFIG_SYS_DDR_BLOCK3_BASE,
+ gd->ram_size -
+ CONFIG_SYS_DDR_BLOCK1_SIZE -
+ CONFIG_SYS_DDR_BLOCK2_SIZE,
+ PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_OUTER_SHARE |
+ PTE_BLOCK_NS |
+ PTE_TYPE_VALID);
+ } else
+#endif
+ {
+ mmu_change_region_attr(
+ CONFIG_SYS_DDR_BLOCK2_BASE,
+ gd->ram_size -
+ CONFIG_SYS_DDR_BLOCK1_SIZE,
+ PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_OUTER_SHARE |
+ PTE_BLOCK_NS |
+ PTE_TYPE_VALID);
+ }
+ }
+}
+
+__weak int dram_init(void)
+{
+ gd->ram_size = initdram(0);
+#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+ /* This will break-before-make MMU for DDR */
+ update_early_mmu_table();
+#endif
+
+ return 0;
}
{
struct ccsr_ahci __iomem *ccsr_ahci = (void *)CONFIG_SYS_SATA;
-#ifdef CONFIG_ARCH_LS1046A
/* Disable SATA ECC */
out_le32((void *)CONFIG_SYS_DCSR_DCFG_ADDR + 0x520, 0x80000000);
-#endif
out_le32(&ccsr_ahci->ppcfg, AHCI_PORT_PHY_1_CFG);
out_le32(&ccsr_ahci->ptc, AHCI_PORT_TRANS_CFG);
out_le32(&ccsr_ahci->axicc, AHCI_PORT_AXICC_CFG);
{
/* Clear global data */
memset((void *)gd, 0, sizeof(gd_t));
-#ifdef CONFIG_LS2080A
- arch_cpu_init();
-#endif
board_early_init_f();
timer_init();
#ifdef CONFIG_LS2080A
};
aliases {
+ serial0 = &usart1;
spi0 = &qspi;
};
};
+&clk_hse {
+ clock-frequency = <25000000>;
+};
+
+&usart1 {
+ pinctrl-0 = <&usart1_pins_a>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
&mac {
status = "okay";
+ pinctrl-0 = <ðernet_mii>;
phy-mode = "rmii";
phy-handle = <&phy0>;
};
&qspi {
+ pinctrl-0 = <&qspi_pins>;
status = "okay";
qflash0: n25q128a {
#include <dt-bindings/pinctrl/stm32f746-pinfunc.h>
/ {
+ clocks {
+ clk_hse: clk-hse {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ };
+};
+
soc {
+ u-boot,dm-pre-reloc;
mac: ethernet@40028000 {
compatible = "st,stm32-dwmac";
reg = <0x40028000 0x8000>;
spi-max-frequency = <108000000>;
status = "disabled";
};
+ usart1: serial@40011000 {
+ compatible = "st,stm32-usart", "st,stm32-uart";
+ reg = <0x40011000 0x400>;
+ interrupts = <37>;
+ clocks = <&rcc 0 164>;
+ status = "disabled";
+ u-boot,dm-pre-reloc;
+ };
+ rcc: rcc@40023810 {
+ #reset-cells = <1>;
+ #clock-cells = <2>;
+ compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
+ reg = <0x40023800 0x400>;
+ clocks = <&clk_hse>;
+ u-boot,dm-pre-reloc;
+ };
+
+ pinctrl: pin-controller {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,stm32f746-pinctrl";
+ ranges = <0 0x40020000 0x3000>;
+ u-boot,dm-pre-reloc;
+ pins-are-numbered;
+
+ usart1_pins_a: usart1@0 {
+ pins1 {
+ pinmux = <STM32F746_PA9_FUNC_USART1_TX>;
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <2>;
+ };
+ pins2 {
+ pinmux = <STM32F746_PB7_FUNC_USART1_RX>;
+ bias-disable;
+ };
+ };
+ ethernet_mii: mii@0 {
+ pins {
+ pinmux = <STM32F746_PG13_FUNC_ETH_MII_TXD0_ETH_RMII_TXD0>,
+ <STM32F746_PG14_FUNC_ETH_MII_TXD1_ETH_RMII_TXD1>,
+ <STM32F746_PG11_FUNC_ETH_MII_TX_EN_ETH_RMII_TX_EN>,
+ <STM32F746_PA2_FUNC_ETH_MDIO>,
+ <STM32F746_PC1_FUNC_ETH_MDC>,
+ <STM32F746_PA1_FUNC_ETH_MII_RX_CLK_ETH_RMII_REF_CLK>,
+ <STM32F746_PA7_FUNC_ETH_MII_RX_DV_ETH_RMII_CRS_DV>,
+ <STM32F746_PC4_FUNC_ETH_MII_RXD0_ETH_RMII_RXD0>,
+ <STM32F746_PC5_FUNC_ETH_MII_RXD1_ETH_RMII_RXD1>;
+ slew-rate = <2>;
+ };
+ };
+ qspi_pins: qspi@0{
+ pins {
+ pinmux = <STM32F746_PB2_FUNC_QUADSPI_CLK>,
+ <STM32F746_PB6_FUNC_QUADSPI_BK1_NCS>,
+ <STM32F746_PD11_FUNC_QUADSPI_BK1_IO0>,
+ <STM32F746_PD12_FUNC_QUADSPI_BK1_IO1>,
+ <STM32F746_PD13_FUNC_QUADSPI_BK1_IO3>,
+ <STM32F746_PE2_FUNC_QUADSPI_BK1_IO2>;
+ slew-rate = <2>;
+ };
+ };
+ };
};
};
};
slcr: slcr@f8000000 {
+ u-boot,dm-pre-reloc;
#address-cells = <1>;
#size-cells = <1>;
compatible = "xlnx,zynq-slcr", "syscon", "simple-mfd";
reg = <0xF8000000 0x1000>;
ranges;
clkc: clkc@100 {
+ u-boot,dm-pre-reloc;
#clock-cells = <1>;
compatible = "xlnx,ps7-clkc";
fclk-enable = <0>;
#define CONFIG_SYS_FSL_OCRAM_SIZE 0x00020000 /* Real size 128K */
/* DDR */
-#define CONFIG_SYS_LS2_DDR_BLOCK1_SIZE ((phys_size_t)2 << 30)
-#define CONFIG_MAX_MEM_MAPPED CONFIG_SYS_LS2_DDR_BLOCK1_SIZE
+#define CONFIG_SYS_DDR_BLOCK1_SIZE ((phys_size_t)2 << 30)
+#define CONFIG_MAX_MEM_MAPPED CONFIG_SYS_DDR_BLOCK1_SIZE
#define CONFIG_SYS_FSL_CCSR_GUR_LE
#define CONFIG_SYS_FSL_CCSR_SCFG_LE
},
{ CONFIG_SYS_FSL_DRAM_BASE1, CONFIG_SYS_FSL_DRAM_BASE1,
CONFIG_SYS_FSL_DRAM_SIZE1,
+#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+#else /* Start with nGnRnE and PXN and UXN to prevent speculative access */
+ PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | PTE_BLOCK_PXN | PTE_BLOCK_UXN |
+#endif
PTE_BLOCK_OUTER_SHARE | PTE_BLOCK_NS
},
/* Map IFC region #2 up to CONFIG_SYS_FLASH_BASE for NAND boot */
},
{ CONFIG_SYS_FSL_DRAM_BASE2, CONFIG_SYS_FSL_DRAM_BASE2,
CONFIG_SYS_FSL_DRAM_SIZE2,
- PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | PTE_BLOCK_PXN | PTE_BLOCK_UXN |
PTE_BLOCK_OUTER_SHARE | PTE_BLOCK_NS
},
#elif defined(CONFIG_FSL_LSCH2)
},
{ CONFIG_SYS_FSL_DRAM_BASE1, CONFIG_SYS_FSL_DRAM_BASE1,
CONFIG_SYS_FSL_DRAM_SIZE1,
+#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+#else /* Start with nGnRnE and PXN and UXN to prevent speculative access */
+ PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | PTE_BLOCK_PXN | PTE_BLOCK_UXN |
+#endif
PTE_BLOCK_OUTER_SHARE | PTE_BLOCK_NS
},
{ CONFIG_SYS_FSL_DRAM_BASE2, CONFIG_SYS_FSL_DRAM_BASE2,
CONFIG_SYS_FSL_DRAM_SIZE2,
- PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | PTE_BLOCK_PXN | PTE_BLOCK_UXN |
PTE_BLOCK_OUTER_SHARE | PTE_BLOCK_NS
},
#endif
u8 res_008[0x20-0x8];
u32 gpporcr1; /* General-purpose POR configuration */
u32 gpporcr2; /* General-purpose POR configuration 2 */
-#define FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT 25
+ u32 gpporcr3;
+ u32 gpporcr4;
+ u8 res_030[0x60-0x30];
+#define FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT 2
#define FSL_CHASSIS3_DCFG_FUSESR_VID_MASK 0x1F
-#define FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT 20
+#define FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT 7
#define FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK 0x1F
u32 dcfg_fusesr; /* Fuse status register */
- u32 gpporcr3;
- u32 gpporcr4;
- u8 res_034[0x70-0x34];
- u32 devdisr; /* Device disable control */
+ u8 res_064[0x70-0x64];
+ u32 devdisr; /* Device disable control 1 */
u32 devdisr2; /* Device disable control 2 */
u32 devdisr3; /* Device disable control 3 */
u32 devdisr4; /* Device disable control 4 */
u32 devdisr5; /* Device disable control 5 */
u32 devdisr6; /* Device disable control 6 */
- u32 devdisr7; /* Device disable control 7 */
+ u8 res_088[0x94-0x88];
+ u32 coredisr; /* Device disable control 7 */
#define FSL_CHASSIS3_DEVDISR2_DPMAC1 0x00000001
#define FSL_CHASSIS3_DEVDISR2_DPMAC2 0x00000002
#define FSL_CHASSIS3_DEVDISR2_DPMAC3 0x00000004
#define FSL_CHASSIS3_DEVDISR2_DPMAC22 0x00200000
#define FSL_CHASSIS3_DEVDISR2_DPMAC23 0x00400000
#define FSL_CHASSIS3_DEVDISR2_DPMAC24 0x00800000
- u8 res_08c[0x90-0x8c];
- u32 coredisru; /* uppper portion for support of 64 cores */
- u32 coredisrl; /* lower portion for support of 64 cores */
u8 res_098[0xa0-0x98];
u32 pvr; /* Processor version */
u32 svr; /* System version */
- u32 mvr; /* Manufacturing version */
- u8 res_0ac[0x100-0xac];
- u32 rcwsr[32]; /* Reset control word status */
+ u8 res_0a8[0x100-0xa8];
+ u32 rcwsr[30]; /* Reset control word status */
#define FSL_CHASSIS3_RCWSR0_SYS_PLL_RAT_SHIFT 2
#define FSL_CHASSIS3_RCWSR0_SYS_PLL_RAT_MASK 0x1f
#define RCW_SB_EN_REG_INDEX 9
#define RCW_SB_EN_MASK 0x00000400
- u8 res_180[0x200-0x180];
- u32 scratchrw[32]; /* Scratch Read/Write */
- u8 res_280[0x300-0x280];
+ u8 res_178[0x200-0x178];
+ u32 scratchrw[16]; /* Scratch Read/Write */
+ u8 res_240[0x300-0x240];
u32 scratchw1r[4]; /* Scratch Read (Write once) */
u8 res_310[0x400-0x310];
u32 bootlocptrl; /* Boot location pointer low-order addr */
u32 bootlocptrh; /* Boot location pointer high-order addr */
- u8 res_408[0x500-0x408];
- u8 res_500[0x740-0x500]; /* add more registers when needed */
+ u8 res_408[0x520-0x408];
+ u32 usb1_amqr;
+ u32 usb2_amqr;
+ u8 res_528[0x530-0x528]; /* add more registers when needed */
+ u32 sdmm1_amqr;
+ u8 res_534[0x550-0x534]; /* add more registers when needed */
+ u32 sata1_amqr;
+ u32 sata2_amqr;
+ u8 res_558[0x570-0x558]; /* add more registers when needed */
+ u32 misc1_amqr;
+ u8 res_574[0x590-0x574]; /* add more registers when needed */
+ u32 spare1_amqr;
+ u32 spare2_amqr;
+ u8 res_598[0x620-0x598]; /* add more registers when needed */
+ u32 gencr[7]; /* General Control Registers */
+ u8 res_63c[0x640-0x63c]; /* add more registers when needed */
+ u32 cgensr1; /* Core General Status Register */
+ u8 res_644[0x660-0x644]; /* add more registers when needed */
+ u32 cgencr1; /* Core General Control Register */
+ u8 res_664[0x740-0x664]; /* add more registers when needed */
u32 tp_ityp[64]; /* Topology Initiator Type Register */
struct {
u32 upper;
u32 lower;
- } tp_cluster[3]; /* Core Cluster n Topology Register */
- u8 res_858[0x1000-0x858];
+ } tp_cluster[4]; /* Core cluster n Topology Register */
+ u8 res_864[0x920-0x864]; /* add more registers when needed */
+ u32 ioqoscr[8]; /*I/O Quality of Services Register */
+ u32 uccr;
+ u8 res_944[0x960-0x944]; /* add more registers when needed */
+ u32 ftmcr;
+ u8 res_964[0x990-0x964]; /* add more registers when needed */
+ u32 coredisablesr;
+ u8 res_994[0xa00-0x994]; /* add more registers when needed */
+ u32 sdbgcr; /*Secure Debug Confifuration Register */
+ u8 res_a04[0xbf8-0xa04]; /* add more registers when needed */
+ u32 ipbrr1;
+ u32 ipbrr2;
+ u8 res_858[0x1000-0xc00];
};
-
struct ccsr_clk_cluster_group {
struct {
u8 res_00[0x10];
#ifndef _ASM_ARMV8_FSL_LAYERSCAPE_MMU_H_
#define _ASM_ARMV8_FSL_LAYERSCAPE_MMU_H_
-#include <asm/arch-armv8/mmu.h>
+void update_early_mmu_table(void);
#endif /* _ASM_ARMV8_FSL_LAYERSCAPE_MMU_H_ */
#ifndef _ASM_ARCH_SYS_PROTO_H
#define _ASM_ARCH_SYS_PROTO_H
-#ifndef CONFIG_CLK_ZYNQMP
-/* Setup clk for network */
-static inline void zynq_slcr_gem_clk_setup(u32 gem_id, unsigned long clk_rate)
-{
-}
-#endif
-
int zynq_slcr_get_mio_pin_status(const char *periph);
unsigned int zynqmp_get_silicon_version(void);
#define PTE_TYPE_FAULT (0 << 0)
#define PTE_TYPE_TABLE (3 << 0)
#define PTE_TYPE_BLOCK (1 << 0)
+#define PTE_TYPE_VALID (1 << 0)
#define PTE_TABLE_PXN (1UL << 59)
#define PTE_TABLE_XN (1UL << 60)
*/
#define PMD_ATTRINDX(t) ((t) << 2)
#define PMD_ATTRINDX_MASK (7 << 2)
+#define PMD_ATTRMASK (PTE_BLOCK_PXN | \
+ PTE_BLOCK_UXN | \
+ PMD_ATTRINDX_MASK | \
+ PTE_TYPE_VALID)
/*
* TCR flags.
#define PLD(code...)
#endif
+/*
+ * We only support cores that support at least Thumb-1 and thus we use
+ * 'bx lr'
+ */
.irp c,,eq,ne,cs,cc,mi,pl,vs,vc,hi,ls,ge,lt,gt,le,hs,lo
.macro ret\c, reg
-#if defined(__ARM_ARCH_5E__)
- mov\c pc, \reg
-#else
.ifeqs "\reg", "lr"
bx\c \reg
.else
mov\c pc, \reg
.endif
-#endif
.endm
.endr
/* For SD boot address and size are assigned in terms of sector
* offset and no. of sectors respectively.
*/
-#define CONFIG_BS_HDR_ADDR_DEVICE 0x00000800
-#define CONFIG_BS_ADDR_DEVICE 0x00000840
+#define CONFIG_BS_HDR_ADDR_DEVICE 0x00000900
+#define CONFIG_BS_ADDR_DEVICE 0x00000940
#define CONFIG_BS_HDR_SIZE 0x00000010
#define CONFIG_BS_SIZE 0x00000008
#else
phys_addr_t secure_ram;
unsigned long tlb_allocated;
#endif
+#ifdef CONFIG_RESV_RAM
+ /*
+ * Reserved RAM for memory resident, eg. Management Complex (MC)
+ * driver which continues to run after U-Boot exits.
+ */
+ phys_addr_t resv_ram;
+#endif
#ifdef CONFIG_ARCH_OMAP2
u32 omap_boot_device;
void smp_kick_all_cpus(void);
void flush_l3_cache(void);
+void mmu_change_region_attr(phys_addr_t start, size_t size, u64 attrs);
/*
*Issue a secure monitor call in accordance with ARM "SMC Calling convention",
*/
#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_STACK)
- ldr sp, =(CONFIG_SPL_STACK)
+ ldr r0, =(CONFIG_SPL_STACK)
#else
- ldr sp, =(CONFIG_SYS_INIT_SP_ADDR)
+ ldr r0, =(CONFIG_SYS_INIT_SP_ADDR)
#endif
-#if defined(CONFIG_CPU_V7M) /* v7M forbids using SP as BIC destination */
- mov r3, sp
- bic r3, r3, #7
- mov sp, r3
-#else
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-#endif
- mov r0, sp
+ bic r0, r0, #7 /* 8-byte alignment for ABI compliance */
+ mov sp, r0
bl board_init_f_alloc_reserve
mov sp, r0
/* set up gd here, outside any C code */
* 'here' but relocated.
*/
- ldr sp, [r9, #GD_START_ADDR_SP] /* sp = gd->start_addr_sp */
-#if defined(CONFIG_CPU_V7M) /* v7M forbids using SP as BIC destination */
- mov r3, sp
- bic r3, r3, #7
- mov sp, r3
-#else
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-#endif
+ ldr r0, [r9, #GD_START_ADDR_SP] /* sp = gd->start_addr_sp */
+ bic r0, r0, #7 /* 8-byte alignment for ABI compliance */
+ mov sp, r0
ldr r9, [r9, #GD_BD] /* r9 = gd->bd */
sub r9, r9, #GD_SIZE /* new GD is below bd */
#endif /* CONFIG_KW88F6281 */
#include <asm/arch/soc.h>
-#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
/*
* functions
*/
-unsigned char get_random_hex(void);
unsigned int mvebu_sdram_bar(enum memory_bank bank);
unsigned int mvebu_sdram_bs(enum memory_bank bank);
void mvebu_sdram_size_adjust(enum memory_bank bank);
# SPDX-License-Identifier: GPL-2.0+
#
-obj-y += timer.o clock.o soc.o
+obj-y += timer.o soc.o
+++ /dev/null
-/*
- * (C) Copyright 2016
- * Vikas Manocha, <vikas.manocha@st.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/rcc.h>
-#include <asm/arch/stm32.h>
-#include <asm/arch/stm32_periph.h>
-
-#define RCC_CR_HSION BIT(0)
-#define RCC_CR_HSEON BIT(16)
-#define RCC_CR_HSERDY BIT(17)
-#define RCC_CR_HSEBYP BIT(18)
-#define RCC_CR_CSSON BIT(19)
-#define RCC_CR_PLLON BIT(24)
-#define RCC_CR_PLLRDY BIT(25)
-
-#define RCC_PLLCFGR_PLLM_MASK GENMASK(5, 0)
-#define RCC_PLLCFGR_PLLN_MASK GENMASK(14, 6)
-#define RCC_PLLCFGR_PLLP_MASK GENMASK(17, 16)
-#define RCC_PLLCFGR_PLLQ_MASK GENMASK(27, 24)
-#define RCC_PLLCFGR_PLLSRC BIT(22)
-#define RCC_PLLCFGR_PLLM_SHIFT 0
-#define RCC_PLLCFGR_PLLN_SHIFT 6
-#define RCC_PLLCFGR_PLLP_SHIFT 16
-#define RCC_PLLCFGR_PLLQ_SHIFT 24
-
-#define RCC_CFGR_AHB_PSC_MASK GENMASK(7, 4)
-#define RCC_CFGR_APB1_PSC_MASK GENMASK(12, 10)
-#define RCC_CFGR_APB2_PSC_MASK GENMASK(15, 13)
-#define RCC_CFGR_SW0 BIT(0)
-#define RCC_CFGR_SW1 BIT(1)
-#define RCC_CFGR_SW_MASK GENMASK(1, 0)
-#define RCC_CFGR_SW_HSI 0
-#define RCC_CFGR_SW_HSE RCC_CFGR_SW0
-#define RCC_CFGR_SW_PLL RCC_CFGR_SW1
-#define RCC_CFGR_SWS0 BIT(2)
-#define RCC_CFGR_SWS1 BIT(3)
-#define RCC_CFGR_SWS_MASK GENMASK(3, 2)
-#define RCC_CFGR_SWS_HSI 0
-#define RCC_CFGR_SWS_HSE RCC_CFGR_SWS0
-#define RCC_CFGR_SWS_PLL RCC_CFGR_SWS1
-#define RCC_CFGR_HPRE_SHIFT 4
-#define RCC_CFGR_PPRE1_SHIFT 10
-#define RCC_CFGR_PPRE2_SHIFT 13
-
-/*
- * Offsets of some PWR registers
- */
-#define PWR_CR1_ODEN BIT(16)
-#define PWR_CR1_ODSWEN BIT(17)
-#define PWR_CSR1_ODRDY BIT(16)
-#define PWR_CSR1_ODSWRDY BIT(17)
-
-struct pll_psc {
- u8 pll_m;
- u16 pll_n;
- u8 pll_p;
- u8 pll_q;
- u8 ahb_psc;
- u8 apb1_psc;
- u8 apb2_psc;
-};
-
-#define AHB_PSC_1 0
-#define AHB_PSC_2 0x8
-#define AHB_PSC_4 0x9
-#define AHB_PSC_8 0xA
-#define AHB_PSC_16 0xB
-#define AHB_PSC_64 0xC
-#define AHB_PSC_128 0xD
-#define AHB_PSC_256 0xE
-#define AHB_PSC_512 0xF
-
-#define APB_PSC_1 0
-#define APB_PSC_2 0x4
-#define APB_PSC_4 0x5
-#define APB_PSC_8 0x6
-#define APB_PSC_16 0x7
-
-#if !defined(CONFIG_STM32_HSE_HZ)
-#error "CONFIG_STM32_HSE_HZ not defined!"
-#else
-#if (CONFIG_STM32_HSE_HZ == 25000000)
-#if (CONFIG_SYS_CLK_FREQ == 200000000)
-/* 200 MHz */
-struct pll_psc sys_pll_psc = {
- .pll_m = 25,
- .pll_n = 400,
- .pll_p = 2,
- .pll_q = 8,
- .ahb_psc = AHB_PSC_1,
- .apb1_psc = APB_PSC_4,
- .apb2_psc = APB_PSC_2
-};
-#endif
-#else
-#error "No PLL/Prescaler configuration for given CONFIG_STM32_HSE_HZ exists"
-#endif
-#endif
-
-int configure_clocks(void)
-{
- /* Reset RCC configuration */
- setbits_le32(&STM32_RCC->cr, RCC_CR_HSION);
- writel(0, &STM32_RCC->cfgr); /* Reset CFGR */
- clrbits_le32(&STM32_RCC->cr, (RCC_CR_HSEON | RCC_CR_CSSON
- | RCC_CR_PLLON));
- writel(0x24003010, &STM32_RCC->pllcfgr); /* Reset value from RM */
- clrbits_le32(&STM32_RCC->cr, RCC_CR_HSEBYP);
- writel(0, &STM32_RCC->cir); /* Disable all interrupts */
-
- /* Configure for HSE+PLL operation */
- setbits_le32(&STM32_RCC->cr, RCC_CR_HSEON);
- while (!(readl(&STM32_RCC->cr) & RCC_CR_HSERDY))
- ;
-
- setbits_le32(&STM32_RCC->cfgr, ((
- sys_pll_psc.ahb_psc << RCC_CFGR_HPRE_SHIFT)
- | (sys_pll_psc.apb1_psc << RCC_CFGR_PPRE1_SHIFT)
- | (sys_pll_psc.apb2_psc << RCC_CFGR_PPRE2_SHIFT)));
-
- /* Configure the main PLL */
- uint32_t pllcfgr = 0;
- pllcfgr = RCC_PLLCFGR_PLLSRC; /* pll source HSE */
- pllcfgr |= sys_pll_psc.pll_m << RCC_PLLCFGR_PLLM_SHIFT;
- pllcfgr |= sys_pll_psc.pll_n << RCC_PLLCFGR_PLLN_SHIFT;
- pllcfgr |= ((sys_pll_psc.pll_p >> 1) - 1) << RCC_PLLCFGR_PLLP_SHIFT;
- pllcfgr |= sys_pll_psc.pll_q << RCC_PLLCFGR_PLLQ_SHIFT;
- writel(pllcfgr, &STM32_RCC->pllcfgr);
-
- /* Enable the main PLL */
- setbits_le32(&STM32_RCC->cr, RCC_CR_PLLON);
- while (!(readl(&STM32_RCC->cr) & RCC_CR_PLLRDY))
- ;
-
- /* Enable high performance mode, System frequency up to 200 MHz */
- setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_PWREN);
- setbits_le32(&STM32_PWR->cr1, PWR_CR1_ODEN);
- /* Infinite wait! */
- while (!(readl(&STM32_PWR->csr1) & PWR_CSR1_ODRDY))
- ;
- /* Enable the Over-drive switch */
- setbits_le32(&STM32_PWR->cr1, PWR_CR1_ODSWEN);
- /* Infinite wait! */
- while (!(readl(&STM32_PWR->csr1) & PWR_CSR1_ODSWRDY))
- ;
-
- stm32_flash_latency_cfg(5);
- clrbits_le32(&STM32_RCC->cfgr, (RCC_CFGR_SW0 | RCC_CFGR_SW1));
- setbits_le32(&STM32_RCC->cfgr, RCC_CFGR_SW_PLL);
-
- while ((readl(&STM32_RCC->cfgr) & RCC_CFGR_SWS_MASK) !=
- RCC_CFGR_SWS_PLL)
- ;
-
- return 0;
-}
-
-unsigned long clock_get(enum clock clck)
-{
- u32 sysclk = 0;
- u32 shift = 0;
- /* Prescaler table lookups for clock computation */
- u8 ahb_psc_table[16] = {
- 0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9
- };
- u8 apb_psc_table[8] = {
- 0, 0, 0, 0, 1, 2, 3, 4
- };
-
- if ((readl(&STM32_RCC->cfgr) & RCC_CFGR_SWS_MASK) ==
- RCC_CFGR_SWS_PLL) {
- u16 pllm, plln, pllp;
- pllm = (readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLM_MASK);
- plln = ((readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLN_MASK)
- >> RCC_PLLCFGR_PLLN_SHIFT);
- pllp = ((((readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLP_MASK)
- >> RCC_PLLCFGR_PLLP_SHIFT) + 1) << 1);
- sysclk = ((CONFIG_STM32_HSE_HZ / pllm) * plln) / pllp;
- }
-
- switch (clck) {
- case CLOCK_CORE:
- return sysclk;
- break;
- case CLOCK_AHB:
- shift = ahb_psc_table[(
- (readl(&STM32_RCC->cfgr) & RCC_CFGR_AHB_PSC_MASK)
- >> RCC_CFGR_HPRE_SHIFT)];
- return sysclk >>= shift;
- break;
- case CLOCK_APB1:
- shift = apb_psc_table[(
- (readl(&STM32_RCC->cfgr) & RCC_CFGR_APB1_PSC_MASK)
- >> RCC_CFGR_PPRE1_SHIFT)];
- return sysclk >>= shift;
- break;
- case CLOCK_APB2:
- shift = apb_psc_table[(
- (readl(&STM32_RCC->cfgr) & RCC_CFGR_APB2_PSC_MASK)
- >> RCC_CFGR_PPRE2_SHIFT)];
- return sysclk >>= shift;
- break;
- default:
- return 0;
- break;
- }
-}
-
-
-void clock_setup(int peripheral)
-{
- switch (peripheral) {
- case USART1_CLOCK_CFG:
- setbits_le32(&STM32_RCC->apb2enr, RCC_APB2ENR_USART1EN);
- break;
- case GPIO_A_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_A_EN);
- break;
- case GPIO_B_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_B_EN);
- break;
- case GPIO_C_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_C_EN);
- break;
- case GPIO_D_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_D_EN);
- break;
- case GPIO_E_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_E_EN);
- break;
- case GPIO_F_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_F_EN);
- break;
- case GPIO_G_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_G_EN);
- break;
- case GPIO_H_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_H_EN);
- break;
- case GPIO_I_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_I_EN);
- break;
- case GPIO_J_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_J_EN);
- break;
- case GPIO_K_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_K_EN);
- break;
- case SYSCFG_CLOCK_CFG:
- setbits_le32(&STM32_RCC->apb2enr, RCC_APB2ENR_SYSCFGEN);
- break;
- case TIMER2_CLOCK_CFG:
- setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_TIM2EN);
- break;
- case FMC_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_FMC_EN);
- break;
- case STMMAC_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_EN);
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_RX_EN);
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_TX_EN);
- break;
- case QSPI_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_QSPI_EN);
- break;
- default:
- break;
- }
-}
int arch_cpu_init(void)
{
- configure_clocks();
-
/*
* Configure the memory protection unit (MPU)
* 0x00000000 - 0xffffffff: Strong-order, Shareable
*
* SPDX-License-Identifier: GPL-2.0+
*/
+#include <clk.h>
#include <common.h>
-#include <errno.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
+#include <dm.h>
#include <asm/arch/clk.h>
-/* Board oscillator frequency */
-#ifndef CONFIG_ZYNQ_PS_CLK_FREQ
-# define CONFIG_ZYNQ_PS_CLK_FREQ 33333333UL
-#endif
-
-/* Register bitfield defines */
-#define PLLCTRL_FBDIV_MASK 0x7f000
-#define PLLCTRL_FBDIV_SHIFT 12
-#define PLLCTRL_BPFORCE_MASK (1 << 4)
-#define PLLCTRL_PWRDWN_MASK 2
-#define PLLCTRL_PWRDWN_SHIFT 1
-#define PLLCTRL_RESET_MASK 1
-#define PLLCTRL_RESET_SHIFT 0
-
-#define ZYNQ_CLK_MAXDIV 0x3f
-#define CLK_CTRL_DIV1_SHIFT 20
-#define CLK_CTRL_DIV1_MASK (ZYNQ_CLK_MAXDIV << CLK_CTRL_DIV1_SHIFT)
-#define CLK_CTRL_DIV0_SHIFT 8
-#define CLK_CTRL_DIV0_MASK (ZYNQ_CLK_MAXDIV << CLK_CTRL_DIV0_SHIFT)
-#define CLK_CTRL_SRCSEL_SHIFT 4
-#define CLK_CTRL_SRCSEL_MASK (0x3 << CLK_CTRL_SRCSEL_SHIFT)
-
-#define CLK_CTRL_DIV2X_SHIFT 26
-#define CLK_CTRL_DIV2X_MASK (ZYNQ_CLK_MAXDIV << CLK_CTRL_DIV2X_SHIFT)
-#define CLK_CTRL_DIV3X_SHIFT 20
-#define CLK_CTRL_DIV3X_MASK (ZYNQ_CLK_MAXDIV << CLK_CTRL_DIV3X_SHIFT)
-
-#define ZYNQ_CLKMUX_SEL_0 0
-#define ZYNQ_CLKMUX_SEL_1 1
-#define ZYNQ_CLKMUX_SEL_2 2
-#define ZYNQ_CLKMUX_SEL_3 3
-
DECLARE_GLOBAL_DATA_PTR;
-struct clk;
-
-/**
- * struct zynq_clk_ops:
- * @set_rate: Function pointer to set_rate() implementation
- * @get_rate: Function pointer to get_rate() implementation
- */
-struct zynq_clk_ops {
- int (*set_rate)(struct clk *clk, unsigned long rate);
- unsigned long (*get_rate)(struct clk *clk);
-};
-
-/**
- * struct clk:
- * @name: Clock name
- * @frequency: Currenct frequency
- * @parent: Parent clock
- * @flags: Clock flags
- * @reg: Clock control register
- * @ops: Clock operations
- */
-struct clk {
- char *name;
- unsigned long frequency;
- enum zynq_clk parent;
- unsigned int flags;
- u32 *reg;
- struct zynq_clk_ops ops;
+static const char * const clk_names[clk_max] = {
+ "armpll", "ddrpll", "iopll",
+ "cpu_6or4x", "cpu_3or2x", "cpu_2x", "cpu_1x",
+ "ddr2x", "ddr3x", "dci",
+ "lqspi", "smc", "pcap", "gem0", "gem1",
+ "fclk0", "fclk1", "fclk2", "fclk3", "can0", "can1",
+ "sdio0", "sdio1", "uart0", "uart1", "spi0", "spi1", "dma",
+ "usb0_aper", "usb1_aper", "gem0_aper", "gem1_aper",
+ "sdio0_aper", "sdio1_aper", "spi0_aper", "spi1_aper",
+ "can0_aper", "can1_aper", "i2c0_aper", "i2c1_aper",
+ "uart0_aper", "uart1_aper", "gpio_aper", "lqspi_aper",
+ "smc_aper", "swdt", "dbg_trc", "dbg_apb"
};
-#define ZYNQ_CLK_FLAGS_HAS_2_DIVS 1
-
-static struct clk clks[clk_max];
-
-/**
- * __zynq_clk_cpu_get_parent() - Decode clock multiplexer
- * @srcsel: Mux select value
- * Returns the clock identifier associated with the selected mux input.
- */
-static int __zynq_clk_cpu_get_parent(unsigned int srcsel)
-{
- unsigned int ret;
-
- switch (srcsel) {
- case ZYNQ_CLKMUX_SEL_0:
- case ZYNQ_CLKMUX_SEL_1:
- ret = armpll_clk;
- break;
- case ZYNQ_CLKMUX_SEL_2:
- ret = ddrpll_clk;
- break;
- case ZYNQ_CLKMUX_SEL_3:
- ret = iopll_clk;
- break;
- default:
- ret = armpll_clk;
- break;
- }
-
- return ret;
-}
-
-/**
- * ddr2x_get_rate() - Get clock rate of DDR2x clock
- * @clk: Clock handle
- * Returns the current clock rate of @clk.
- */
-static unsigned long ddr2x_get_rate(struct clk *clk)
-{
- u32 clk_ctrl = readl(clk->reg);
- u32 div = (clk_ctrl & CLK_CTRL_DIV2X_MASK) >> CLK_CTRL_DIV2X_SHIFT;
-
- return DIV_ROUND_CLOSEST(zynq_clk_get_rate(clk->parent), div);
-}
-
-/**
- * ddr3x_get_rate() - Get clock rate of DDR3x clock
- * @clk: Clock handle
- * Returns the current clock rate of @clk.
- */
-static unsigned long ddr3x_get_rate(struct clk *clk)
-{
- u32 clk_ctrl = readl(clk->reg);
- u32 div = (clk_ctrl & CLK_CTRL_DIV3X_MASK) >> CLK_CTRL_DIV3X_SHIFT;
-
- return DIV_ROUND_CLOSEST(zynq_clk_get_rate(clk->parent), div);
-}
-
-static void init_ddr_clocks(void)
-{
- u32 div0, div1;
- unsigned long prate = zynq_clk_get_rate(ddrpll_clk);
- u32 clk_ctrl = readl(&slcr_base->ddr_clk_ctrl);
-
- /* DDR2x */
- clks[ddr2x_clk].reg = &slcr_base->ddr_clk_ctrl;
- clks[ddr2x_clk].parent = ddrpll_clk;
- clks[ddr2x_clk].name = "ddr_2x";
- clks[ddr2x_clk].frequency = ddr2x_get_rate(&clks[ddr2x_clk]);
- clks[ddr2x_clk].ops.get_rate = ddr2x_get_rate;
-
- /* DDR3x */
- clks[ddr3x_clk].reg = &slcr_base->ddr_clk_ctrl;
- clks[ddr3x_clk].parent = ddrpll_clk;
- clks[ddr3x_clk].name = "ddr_3x";
- clks[ddr3x_clk].frequency = ddr3x_get_rate(&clks[ddr3x_clk]);
- clks[ddr3x_clk].ops.get_rate = ddr3x_get_rate;
-
- /* DCI */
- clk_ctrl = readl(&slcr_base->dci_clk_ctrl);
- div0 = (clk_ctrl & CLK_CTRL_DIV0_MASK) >> CLK_CTRL_DIV0_SHIFT;
- div1 = (clk_ctrl & CLK_CTRL_DIV1_MASK) >> CLK_CTRL_DIV1_SHIFT;
- clks[dci_clk].reg = &slcr_base->dci_clk_ctrl;
- clks[dci_clk].parent = ddrpll_clk;
- clks[dci_clk].frequency = DIV_ROUND_CLOSEST(
- DIV_ROUND_CLOSEST(prate, div0), div1);
- clks[dci_clk].name = "dci";
-
- gd->bd->bi_ddr_freq = clks[ddr3x_clk].frequency / 1000000;
-}
-
-static void init_cpu_clocks(void)
-{
- int clk_621;
- u32 reg, div, srcsel;
- enum zynq_clk parent;
-
- reg = readl(&slcr_base->arm_clk_ctrl);
- clk_621 = readl(&slcr_base->clk_621_true) & 1;
- div = (reg & CLK_CTRL_DIV0_MASK) >> CLK_CTRL_DIV0_SHIFT;
- srcsel = (reg & CLK_CTRL_SRCSEL_MASK) >> CLK_CTRL_SRCSEL_SHIFT;
- parent = __zynq_clk_cpu_get_parent(srcsel);
-
- /* cpu clocks */
- clks[cpu_6or4x_clk].reg = &slcr_base->arm_clk_ctrl;
- clks[cpu_6or4x_clk].parent = parent;
- clks[cpu_6or4x_clk].frequency = DIV_ROUND_CLOSEST(
- zynq_clk_get_rate(parent), div);
- clks[cpu_6or4x_clk].name = "cpu_6or4x";
-
- clks[cpu_3or2x_clk].reg = &slcr_base->arm_clk_ctrl;
- clks[cpu_3or2x_clk].parent = cpu_6or4x_clk;
- clks[cpu_3or2x_clk].frequency = zynq_clk_get_rate(cpu_6or4x_clk) / 2;
- clks[cpu_3or2x_clk].name = "cpu_3or2x";
-
- clks[cpu_2x_clk].reg = &slcr_base->arm_clk_ctrl;
- clks[cpu_2x_clk].parent = cpu_6or4x_clk;
- clks[cpu_2x_clk].frequency = zynq_clk_get_rate(cpu_6or4x_clk) /
- (2 + clk_621);
- clks[cpu_2x_clk].name = "cpu_2x";
-
- clks[cpu_1x_clk].reg = &slcr_base->arm_clk_ctrl;
- clks[cpu_1x_clk].parent = cpu_6or4x_clk;
- clks[cpu_1x_clk].frequency = zynq_clk_get_rate(cpu_6or4x_clk) /
- (4 + 2 * clk_621);
- clks[cpu_1x_clk].name = "cpu_1x";
-}
-
-/**
- * periph_calc_two_divs() - Calculate clock dividers
- * @cur_rate: Current clock rate
- * @tgt_rate: Target clock rate
- * @prate: Parent clock rate
- * @div0: First divider (output)
- * @div1: Second divider (output)
- * Returns the actual clock rate possible.
- *
- * Calculates clock dividers for clocks with two 6-bit dividers.
- */
-static unsigned long periph_calc_two_divs(unsigned long cur_rate,
- unsigned long tgt_rate, unsigned long prate, u32 *div0,
- u32 *div1)
-{
- long err, best_err = (long)(~0UL >> 1);
- unsigned long rate, best_rate = 0;
- u32 d0, d1;
-
- for (d0 = 1; d0 <= ZYNQ_CLK_MAXDIV; d0++) {
- for (d1 = 1; d1 <= ZYNQ_CLK_MAXDIV >> 1; d1++) {
- rate = DIV_ROUND_CLOSEST(DIV_ROUND_CLOSEST(prate, d0),
- d1);
- err = abs(rate - tgt_rate);
-
- if (err < best_err) {
- *div0 = d0;
- *div1 = d1;
- best_err = err;
- best_rate = rate;
- }
- }
- }
-
- return best_rate;
-}
-
-/**
- * zynq_clk_periph_set_rate() - Set clock rate
- * @clk: Handle of the peripheral clock
- * @rate: New clock rate
- * Sets the clock frequency of @clk to @rate. Returns zero on success.
- */
-static int zynq_clk_periph_set_rate(struct clk *clk,
- unsigned long rate)
-{
- u32 ctrl, div0 = 0, div1 = 0;
- unsigned long prate, new_rate, cur_rate = clk->frequency;
-
- ctrl = readl(clk->reg);
- prate = zynq_clk_get_rate(clk->parent);
- ctrl &= ~CLK_CTRL_DIV0_MASK;
-
- if (clk->flags & ZYNQ_CLK_FLAGS_HAS_2_DIVS) {
- ctrl &= ~CLK_CTRL_DIV1_MASK;
- new_rate = periph_calc_two_divs(cur_rate, rate, prate, &div0,
- &div1);
- ctrl |= div1 << CLK_CTRL_DIV1_SHIFT;
- } else {
- div0 = DIV_ROUND_CLOSEST(prate, rate);
- div0 &= ZYNQ_CLK_MAXDIV;
- new_rate = DIV_ROUND_CLOSEST(rate, div0);
- }
-
- /* write new divs to hardware */
- ctrl |= div0 << CLK_CTRL_DIV0_SHIFT;
- writel(ctrl, clk->reg);
-
- /* update frequency in clk framework */
- clk->frequency = new_rate;
-
- return 0;
-}
-
-/**
- * zynq_clk_periph_get_rate() - Get clock rate
- * @clk: Handle of the peripheral clock
- * Returns the current clock rate of @clk.
- */
-static unsigned long zynq_clk_periph_get_rate(struct clk *clk)
-{
- u32 clk_ctrl = readl(clk->reg);
- u32 div0 = (clk_ctrl & CLK_CTRL_DIV0_MASK) >> CLK_CTRL_DIV0_SHIFT;
- u32 div1 = 1;
-
- if (clk->flags & ZYNQ_CLK_FLAGS_HAS_2_DIVS)
- div1 = (clk_ctrl & CLK_CTRL_DIV1_MASK) >> CLK_CTRL_DIV1_SHIFT;
-
- /* a register value of zero == division by 1 */
- if (!div0)
- div0 = 1;
- if (!div1)
- div1 = 1;
-
- return
- DIV_ROUND_CLOSEST(
- DIV_ROUND_CLOSEST(zynq_clk_get_rate(clk->parent), div0),
- div1);
-}
-
-/**
- * __zynq_clk_periph_get_parent() - Decode clock multiplexer
- * @srcsel: Mux select value
- * Returns the clock identifier associated with the selected mux input.
- */
-static enum zynq_clk __zynq_clk_periph_get_parent(u32 srcsel)
-{
- switch (srcsel) {
- case ZYNQ_CLKMUX_SEL_0:
- case ZYNQ_CLKMUX_SEL_1:
- return iopll_clk;
- case ZYNQ_CLKMUX_SEL_2:
- return armpll_clk;
- case ZYNQ_CLKMUX_SEL_3:
- return ddrpll_clk;
- default:
- return 0;
- }
-}
-
-/**
- * zynq_clk_periph_get_parent() - Decode clock multiplexer
- * @clk: Clock handle
- * Returns the clock identifier associated with the selected mux input.
- */
-static enum zynq_clk zynq_clk_periph_get_parent(struct clk *clk)
-{
- u32 clk_ctrl = readl(clk->reg);
- u32 srcsel = (clk_ctrl & CLK_CTRL_SRCSEL_MASK) >> CLK_CTRL_SRCSEL_SHIFT;
-
- return __zynq_clk_periph_get_parent(srcsel);
-}
-
-/**
- * zynq_clk_register_periph_clk() - Set up a peripheral clock with the framework
- * @clk: Pointer to struct clk for the clock
- * @ctrl: Clock control register
- * @name: PLL name
- * @two_divs: Indicates whether the clock features one or two dividers
- */
-static int zynq_clk_register_periph_clk(struct clk *clk, u32 *ctrl, char *name,
- bool two_divs)
-{
- clk->name = name;
- clk->reg = ctrl;
- if (two_divs)
- clk->flags = ZYNQ_CLK_FLAGS_HAS_2_DIVS;
- clk->parent = zynq_clk_periph_get_parent(clk);
- clk->frequency = zynq_clk_periph_get_rate(clk);
- clk->ops.get_rate = zynq_clk_periph_get_rate;
- clk->ops.set_rate = zynq_clk_periph_set_rate;
-
- return 0;
-}
-
-static void init_periph_clocks(void)
-{
- zynq_clk_register_periph_clk(&clks[gem0_clk], &slcr_base->gem0_clk_ctrl,
- "gem0", 1);
- zynq_clk_register_periph_clk(&clks[gem1_clk], &slcr_base->gem1_clk_ctrl,
- "gem1", 1);
-
- zynq_clk_register_periph_clk(&clks[smc_clk], &slcr_base->smc_clk_ctrl,
- "smc", 0);
-
- zynq_clk_register_periph_clk(&clks[lqspi_clk],
- &slcr_base->lqspi_clk_ctrl, "lqspi", 0);
-
- zynq_clk_register_periph_clk(&clks[sdio0_clk],
- &slcr_base->sdio_clk_ctrl, "sdio0", 0);
- zynq_clk_register_periph_clk(&clks[sdio1_clk],
- &slcr_base->sdio_clk_ctrl, "sdio1", 0);
-
- zynq_clk_register_periph_clk(&clks[spi0_clk], &slcr_base->spi_clk_ctrl,
- "spi0", 0);
- zynq_clk_register_periph_clk(&clks[spi1_clk], &slcr_base->spi_clk_ctrl,
- "spi1", 0);
-
- zynq_clk_register_periph_clk(&clks[uart0_clk],
- &slcr_base->uart_clk_ctrl, "uart0", 0);
- zynq_clk_register_periph_clk(&clks[uart1_clk],
- &slcr_base->uart_clk_ctrl, "uart1", 0);
-
- zynq_clk_register_periph_clk(&clks[dbg_trc_clk],
- &slcr_base->dbg_clk_ctrl, "dbg_trc", 0);
- zynq_clk_register_periph_clk(&clks[dbg_apb_clk],
- &slcr_base->dbg_clk_ctrl, "dbg_apb", 0);
-
- zynq_clk_register_periph_clk(&clks[pcap_clk],
- &slcr_base->pcap_clk_ctrl, "pcap", 0);
-
- zynq_clk_register_periph_clk(&clks[fclk0_clk],
- &slcr_base->fpga0_clk_ctrl, "fclk0", 1);
- zynq_clk_register_periph_clk(&clks[fclk1_clk],
- &slcr_base->fpga1_clk_ctrl, "fclk1", 1);
- zynq_clk_register_periph_clk(&clks[fclk2_clk],
- &slcr_base->fpga2_clk_ctrl, "fclk2", 1);
- zynq_clk_register_periph_clk(&clks[fclk3_clk],
- &slcr_base->fpga3_clk_ctrl, "fclk3", 1);
-}
-
-/**
- * zynq_clk_register_aper_clk() - Set up a APER clock with the framework
- * @clk: Pointer to struct clk for the clock
- * @ctrl: Clock control register
- * @name: PLL name
- */
-static void zynq_clk_register_aper_clk(struct clk *clk, u32 *ctrl, char *name)
-{
- clk->name = name;
- clk->reg = ctrl;
- clk->parent = cpu_1x_clk;
- clk->frequency = zynq_clk_get_rate(clk->parent);
-}
-
-static void init_aper_clocks(void)
-{
- zynq_clk_register_aper_clk(&clks[usb0_aper_clk],
- &slcr_base->aper_clk_ctrl, "usb0_aper");
- zynq_clk_register_aper_clk(&clks[usb1_aper_clk],
- &slcr_base->aper_clk_ctrl, "usb1_aper");
-
- zynq_clk_register_aper_clk(&clks[gem0_aper_clk],
- &slcr_base->aper_clk_ctrl, "gem0_aper");
- zynq_clk_register_aper_clk(&clks[gem1_aper_clk],
- &slcr_base->aper_clk_ctrl, "gem1_aper");
-
- zynq_clk_register_aper_clk(&clks[sdio0_aper_clk],
- &slcr_base->aper_clk_ctrl, "sdio0_aper");
- zynq_clk_register_aper_clk(&clks[sdio1_aper_clk],
- &slcr_base->aper_clk_ctrl, "sdio1_aper");
-
- zynq_clk_register_aper_clk(&clks[spi0_aper_clk],
- &slcr_base->aper_clk_ctrl, "spi0_aper");
- zynq_clk_register_aper_clk(&clks[spi1_aper_clk],
- &slcr_base->aper_clk_ctrl, "spi1_aper");
-
- zynq_clk_register_aper_clk(&clks[can0_aper_clk],
- &slcr_base->aper_clk_ctrl, "can0_aper");
- zynq_clk_register_aper_clk(&clks[can1_aper_clk],
- &slcr_base->aper_clk_ctrl, "can1_aper");
-
- zynq_clk_register_aper_clk(&clks[i2c0_aper_clk],
- &slcr_base->aper_clk_ctrl, "i2c0_aper");
- zynq_clk_register_aper_clk(&clks[i2c1_aper_clk],
- &slcr_base->aper_clk_ctrl, "i2c1_aper");
-
- zynq_clk_register_aper_clk(&clks[uart0_aper_clk],
- &slcr_base->aper_clk_ctrl, "uart0_aper");
- zynq_clk_register_aper_clk(&clks[uart1_aper_clk],
- &slcr_base->aper_clk_ctrl, "uart1_aper");
-
- zynq_clk_register_aper_clk(&clks[gpio_aper_clk],
- &slcr_base->aper_clk_ctrl, "gpio_aper");
-
- zynq_clk_register_aper_clk(&clks[lqspi_aper_clk],
- &slcr_base->aper_clk_ctrl, "lqspi_aper");
-
- zynq_clk_register_aper_clk(&clks[smc_aper_clk],
- &slcr_base->aper_clk_ctrl, "smc_aper");
-}
-
-/**
- * __zynq_clk_pll_get_rate() - Get PLL rate
- * @addr: Address of the PLL's control register
- * Returns the current PLL output rate.
- */
-static unsigned long __zynq_clk_pll_get_rate(u32 *addr)
-{
- u32 reg, mul, bypass;
-
- reg = readl(addr);
- bypass = reg & PLLCTRL_BPFORCE_MASK;
- if (bypass)
- mul = 1;
- else
- mul = (reg & PLLCTRL_FBDIV_MASK) >> PLLCTRL_FBDIV_SHIFT;
-
- return CONFIG_ZYNQ_PS_CLK_FREQ * mul;
-}
-
-/**
- * zynq_clk_pll_get_rate() - Get PLL rate
- * @pll: Handle of the PLL
- * Returns the current clock rate of @pll.
- */
-static unsigned long zynq_clk_pll_get_rate(struct clk *pll)
-{
- return __zynq_clk_pll_get_rate(pll->reg);
-}
-
-/**
- * zynq_clk_register_pll() - Set up a PLL with the framework
- * @clk: Pointer to struct clk for the PLL
- * @ctrl: PLL control register
- * @name: PLL name
- * @prate: PLL input clock rate
- */
-static void zynq_clk_register_pll(struct clk *clk, u32 *ctrl, char *name,
- unsigned long prate)
-{
- clk->name = name;
- clk->reg = ctrl;
- clk->frequency = zynq_clk_pll_get_rate(clk);
- clk->ops.get_rate = zynq_clk_pll_get_rate;
-}
-
-/**
- * clkid_2_register() - Get clock control register
- * @id: Clock identifier of one of the PLLs
- * Returns the address of the requested PLL's control register.
- */
-static u32 *clkid_2_register(enum zynq_clk id)
-{
- switch (id) {
- case armpll_clk:
- return &slcr_base->arm_pll_ctrl;
- case ddrpll_clk:
- return &slcr_base->ddr_pll_ctrl;
- case iopll_clk:
- return &slcr_base->io_pll_ctrl;
- default:
- return &slcr_base->io_pll_ctrl;
- }
-}
-
-/* API */
-/**
- * zynq_clk_early_init() - Early init for the clock framework
- *
- * This function is called from before relocation and sets up the CPU clock
- * frequency in the global data struct.
- */
-void zynq_clk_early_init(void)
-{
- u32 reg = readl(&slcr_base->arm_clk_ctrl);
- u32 div = (reg & CLK_CTRL_DIV0_MASK) >> CLK_CTRL_DIV0_SHIFT;
- u32 srcsel = (reg & CLK_CTRL_SRCSEL_MASK) >> CLK_CTRL_SRCSEL_SHIFT;
- enum zynq_clk parent = __zynq_clk_cpu_get_parent(srcsel);
- u32 *pllreg = clkid_2_register(parent);
- unsigned long prate = __zynq_clk_pll_get_rate(pllreg);
-
- if (!div)
- div = 1;
-
- gd->cpu_clk = DIV_ROUND_CLOSEST(prate, div);
-}
-
-/**
- * get_uart_clk() - Get UART input frequency
- * @dev_index: UART ID
- * Returns UART input clock frequency in Hz.
- *
- * Compared to zynq_clk_get_rate() this function is designed to work before
- * relocation and can be called when the serial UART is set up.
- */
-unsigned long get_uart_clk(int dev_index)
-{
- u32 reg = readl(&slcr_base->uart_clk_ctrl);
- u32 div = (reg & CLK_CTRL_DIV0_MASK) >> CLK_CTRL_DIV0_SHIFT;
- u32 srcsel = (reg & CLK_CTRL_SRCSEL_MASK) >> CLK_CTRL_SRCSEL_SHIFT;
- enum zynq_clk parent = __zynq_clk_periph_get_parent(srcsel);
- u32 *pllreg = clkid_2_register(parent);
- unsigned long prate = __zynq_clk_pll_get_rate(pllreg);
-
- if (!div)
- div = 1;
-
- return DIV_ROUND_CLOSEST(prate, div);
-}
/**
- * set_cpu_clk_info() - Initialize clock framework
- * Always returns zero.
+ * set_cpu_clk_info() - Setup clock information
*
* This function is called from common code after relocation and sets up the
- * clock framework. The framework must not be used before this function had been
- * called.
+ * clock information.
*/
int set_cpu_clk_info(void)
{
- zynq_clk_register_pll(&clks[armpll_clk], &slcr_base->arm_pll_ctrl,
- "armpll", CONFIG_ZYNQ_PS_CLK_FREQ);
- zynq_clk_register_pll(&clks[ddrpll_clk], &slcr_base->ddr_pll_ctrl,
- "ddrpll", CONFIG_ZYNQ_PS_CLK_FREQ);
- zynq_clk_register_pll(&clks[iopll_clk], &slcr_base->io_pll_ctrl,
- "iopll", CONFIG_ZYNQ_PS_CLK_FREQ);
-
- init_ddr_clocks();
- init_cpu_clocks();
- init_periph_clocks();
- init_aper_clocks();
-
- gd->bd->bi_arm_freq = gd->cpu_clk / 1000000;
+ struct clk clk;
+ struct udevice *dev;
+ ulong rate;
+ int i, ret;
+
+ ret = uclass_get_device_by_driver(UCLASS_CLK,
+ DM_GET_DRIVER(zynq_clk), &dev);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < 2; i++) {
+ clk.id = i ? ddr3x_clk : cpu_6or4x_clk;
+ ret = clk_request(dev, &clk);
+ if (ret < 0)
+ return ret;
+
+ rate = clk_get_rate(&clk) / 1000000;
+ if (i)
+ gd->bd->bi_ddr_freq = rate;
+ else
+ gd->bd->bi_arm_freq = rate;
+
+ clk_free(&clk);
+ }
gd->bd->bi_dsp_freq = 0;
return 0;
}
-/**
- * zynq_clk_get_rate() - Get clock rate
- * @clk: Clock identifier
- * Returns the current clock rate of @clk on success or zero for an invalid
- * clock id.
- */
-unsigned long zynq_clk_get_rate(enum zynq_clk clk)
-{
- if (clk < 0 || clk >= clk_max)
- return 0;
-
- return clks[clk].frequency;
-}
-
-/**
- * zynq_clk_set_rate() - Set clock rate
- * @clk: Clock identifier
- * @rate: Requested clock rate
- * Passes on the return value from the clock's set_rate() function or negative
- * errno.
- */
-int zynq_clk_set_rate(enum zynq_clk clk, unsigned long rate)
-{
- if (clk < 0 || clk >= clk_max)
- return -ENODEV;
-
- if (clks[clk].ops.set_rate)
- return clks[clk].ops.set_rate(&clks[clk], rate);
-
- return -ENXIO;
-}
-
-/**
- * zynq_clk_get_name() - Get clock name
- * @clk: Clock identifier
- * Returns the name of @clk.
- */
-const char *zynq_clk_get_name(enum zynq_clk clk)
-{
- return clks[clk].name;
-}
-
/**
* soc_clk_dump() - Print clock frequencies
* Returns zero on success
*/
int soc_clk_dump(void)
{
- int i;
+ struct udevice *dev;
+ int i, ret;
+
+ ret = uclass_get_device_by_driver(UCLASS_CLK,
+ DM_GET_DRIVER(zynq_clk), &dev);
+ if (ret)
+ return ret;
printf("clk\t\tfrequency\n");
for (i = 0; i < clk_max; i++) {
- const char *name = zynq_clk_get_name(i);
- if (name)
- printf("%10s%20lu\n", name, zynq_clk_get_rate(i));
+ const char *name = clk_names[i];
+ if (name) {
+ struct clk clk;
+ unsigned long rate;
+
+ clk.id = i;
+ ret = clk_request(dev, &clk);
+ if (ret < 0)
+ return ret;
+
+ rate = clk_get_rate(&clk);
+
+ clk_free(&clk);
+
+ if (rate == (unsigned long)-ENOSYS)
+ printf("%10s%20s\n", name, "unknown");
+ else
+ printf("%10s%20lu\n", name, rate);
+ }
}
return 0;
writel(0xC, &slcr_base->ddr_urgent);
#endif
#endif
- zynq_clk_early_init();
zynq_slcr_lock();
return 0;
uart0_aper_clk, uart1_aper_clk, gpio_aper_clk, lqspi_aper_clk,
smc_aper_clk, swdt_clk, dbg_trc_clk, dbg_apb_clk, clk_max};
-void zynq_clk_early_init(void);
-int zynq_clk_set_rate(enum zynq_clk clk, unsigned long rate);
-unsigned long zynq_clk_get_rate(enum zynq_clk clk);
-const char *zynq_clk_get_name(enum zynq_clk clk);
-unsigned long get_uart_clk(int dev_id);
-
#endif
extern void zynq_slcr_lock(void);
extern void zynq_slcr_unlock(void);
extern void zynq_slcr_cpu_reset(void);
-extern void zynq_slcr_gem_clk_setup(u32 gem_id, unsigned long clk_rate);
extern void zynq_slcr_devcfg_disable(void);
extern void zynq_slcr_devcfg_enable(void);
extern u32 zynq_slcr_get_boot_mode(void);
#include <malloc.h>
#include <asm/arch/hardware.h>
#include <asm/arch/sys_proto.h>
-#include <asm/arch/clk.h>
#define SLCR_LOCK_MAGIC 0x767B
#define SLCR_UNLOCK_MAGIC 0xDF0D
writel(1, &slcr_base->pss_rst_ctrl);
}
-/* Setup clk for network */
-void zynq_slcr_gem_clk_setup(u32 gem_id, unsigned long clk_rate)
-{
- int ret;
-
- zynq_slcr_unlock();
-
- if (gem_id > 1) {
- printf("Non existing GEM id %d\n", gem_id);
- goto out;
- }
-
- ret = zynq_clk_set_rate(gem0_clk + gem_id, clk_rate);
- if (ret)
- goto out;
-
- if (gem_id) {
- /* Configure GEM_RCLK_CTRL */
- writel(1, &slcr_base->gem1_rclk_ctrl);
- } else {
- /* Configure GEM_RCLK_CTRL */
- writel(1, &slcr_base->gem0_rclk_ctrl);
- }
- udelay(100000);
-out:
- zynq_slcr_lock();
-}
-
void zynq_slcr_devcfg_disable(void)
{
u32 reg_val;
/*
+ * Copyright (C) 2017 Weidmüller Interface GmbH & Co. KG
+ * Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
+ *
* Copyright (C) 2012 Michal Simek <monstr@monstr.eu>
* Copyright (C) 2011-2012 Xilinx, Inc. All rights reserved.
*
* SPDX-License-Identifier: GPL-2.0+
*/
+#include <clk.h>
#include <common.h>
#include <div64.h>
+#include <dm.h>
#include <asm/io.h>
#include <asm/arch/hardware.h>
#include <asm/arch/clk.h>
(TIMER_PRESCALE << SCUTIMER_CONTROL_PRESCALER_SHIFT) |
SCUTIMER_CONTROL_ENABLE_MASK;
+ struct udevice *dev;
+ struct clk clk;
+ int ret;
+
+ ret = uclass_get_device_by_driver(UCLASS_CLK,
+ DM_GET_DRIVER(zynq_clk), &dev);
+ if (ret)
+ return ret;
+
+ clk.id = cpu_6or4x_clk;
+ ret = clk_request(dev, &clk);
+ if (ret < 0)
+ return ret;
+
+ gd->cpu_clk = clk_get_rate(&clk);
+
+ clk_free(&clk);
+
gd->arch.timer_rate_hz = (gd->cpu_clk / 2) / (TIMER_PRESCALE + 1);
/* Load the timer counter register */
return vdd_last;
}
+#ifdef CONFIG_FSL_LSCH3
int adjust_vdd(ulong vdd_override)
{
int re_enable = disable_interrupts();
-#if defined(CONFIG_FSL_LSCH2) || defined(CONFIG_FSL_LSCH3)
+ struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+ u32 fusesr;
+ u8 vid, buf;
+ int vdd_target, vdd_current, vdd_last;
+ int ret, i2caddress;
+ unsigned long vdd_string_override;
+ char *vdd_string;
+ static const uint16_t vdd[32] = {
+ 10500,
+ 0, /* reserved */
+ 9750,
+ 0, /* reserved */
+ 9500,
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 10000, /* 1.0000V */
+ 0, /* reserved */
+ 10250,
+ 0, /* reserved */
+ 10500,
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ 0, /* reserved */
+ };
+ struct vdd_drive {
+ u8 vid;
+ unsigned voltage;
+ };
+
+ ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR);
+ if (ret) {
+ debug("VID: I2C failed to switch channel\n");
+ ret = -1;
+ goto exit;
+ }
+ ret = find_ir_chip_on_i2c();
+ if (ret < 0) {
+ printf("VID: Could not find voltage regulator on I2C.\n");
+ ret = -1;
+ goto exit;
+ } else {
+ i2caddress = ret;
+ debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress);
+ }
+
+ /* check IR chip work on Intel mode*/
+ ret = i2c_read(i2caddress,
+ IR36021_INTEL_MODE_OOFSET,
+ 1, (void *)&buf, 1);
+ if (ret) {
+ printf("VID: failed to read IR chip mode.\n");
+ ret = -1;
+ goto exit;
+ }
+ if ((buf & IR36021_MODE_MASK) != IR36021_INTEL_MODE) {
+ printf("VID: IR Chip is not used in Intel mode.\n");
+ ret = -1;
+ goto exit;
+ }
+
+ /* get the voltage ID from fuse status register */
+ fusesr = in_le32(&gur->dcfg_fusesr);
+ vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT) &
+ FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK;
+ if ((vid == 0) || (vid == FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK)) {
+ vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT) &
+ FSL_CHASSIS3_DCFG_FUSESR_VID_MASK;
+ }
+ vdd_target = vdd[vid];
+
+ /* check override variable for overriding VDD */
+ vdd_string = getenv(CONFIG_VID_FLS_ENV);
+ if (vdd_override == 0 && vdd_string &&
+ !strict_strtoul(vdd_string, 10, &vdd_string_override))
+ vdd_override = vdd_string_override;
+
+ if (vdd_override >= VDD_MV_MIN && vdd_override <= VDD_MV_MAX) {
+ vdd_target = vdd_override * 10; /* convert to 1/10 mV */
+ debug("VDD override is %lu\n", vdd_override);
+ } else if (vdd_override != 0) {
+ printf("Invalid value.\n");
+ }
+
+ /* divide and round up by 10 to get a value in mV */
+ vdd_target = DIV_ROUND_UP(vdd_target, 10);
+ if (vdd_target == 0) {
+ debug("VID: VID not used\n");
+ ret = 0;
+ goto exit;
+ } else if (vdd_target < VDD_MV_MIN || vdd_target > VDD_MV_MAX) {
+ /* Check vdd_target is in valid range */
+ printf("VID: Target VID %d mV is not in range.\n",
+ vdd_target);
+ ret = -1;
+ goto exit;
+ } else {
+ debug("VID: vid = %d mV\n", vdd_target);
+ }
+
+ /*
+ * Read voltage monitor to check real voltage.
+ */
+ vdd_last = read_voltage(i2caddress);
+ if (vdd_last < 0) {
+ printf("VID: Couldn't read sensor abort VID adjustment\n");
+ ret = -1;
+ goto exit;
+ }
+ vdd_current = vdd_last;
+ debug("VID: Core voltage is currently at %d mV\n", vdd_last);
+ /*
+ * Adjust voltage to at or one step above target.
+ * As measurements are less precise than setting the values
+ * we may run through dummy steps that cancel each other
+ * when stepping up and then down.
+ */
+ while (vdd_last > 0 &&
+ vdd_last < vdd_target) {
+ vdd_current += IR_VDD_STEP_UP;
+ vdd_last = set_voltage(i2caddress, vdd_current);
+ }
+ while (vdd_last > 0 &&
+ vdd_last > vdd_target + (IR_VDD_STEP_DOWN - 1)) {
+ vdd_current -= IR_VDD_STEP_DOWN;
+ vdd_last = set_voltage(i2caddress, vdd_current);
+ }
+
+ if (vdd_last > 0)
+ printf("VID: Core voltage after adjustment is at %d mV\n",
+ vdd_last);
+ else
+ ret = -1;
+exit:
+ if (re_enable)
+ enable_interrupts();
+ i2c_multiplexer_select_vid_channel(I2C_MUX_CH_DEFAULT);
+ return ret;
+}
+#else /* !CONFIG_FSL_LSCH3 */
+int adjust_vdd(ulong vdd_override)
+{
+ int re_enable = disable_interrupts();
+#if defined(CONFIG_FSL_LSCH2)
struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
#else
ccsr_gur_t __iomem *gur =
}
/* get the voltage ID from fuse status register */
-#ifdef CONFIG_FSL_LSCH3
- fusesr = in_le32(&gur->dcfg_fusesr);
-#else
fusesr = in_be32(&gur->dcfg_fusesr);
-#endif
/*
* VID is used according to the table below
* ---------------------------------------
vid = (fusesr >> FSL_CHASSIS2_DCFG_FUSESR_VID_SHIFT) &
FSL_CHASSIS2_DCFG_FUSESR_VID_MASK;
}
-#elif defined(CONFIG_FSL_LSCH3)
- vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_ALTVID_SHIFT) &
- FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK;
- if ((vid == 0) || (vid == FSL_CHASSIS3_DCFG_FUSESR_ALTVID_MASK)) {
- vid = (fusesr >> FSL_CHASSIS3_DCFG_FUSESR_VID_SHIFT) &
- FSL_CHASSIS3_DCFG_FUSESR_VID_MASK;
- }
#else
vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) &
FSL_CORENET_DCFG_FUSESR_ALTVID_MASK;
return ret;
}
+#endif
static int print_vdd(void)
{
#ifdef CONFIG_FSL_LS_PPA
#include <asm/arch/ppa.h>
#endif
+#include <asm/arch/mmu.h>
#include <asm/arch/soc.h>
#include <hwconfig.h>
#include <environment.h>
mmdc_init(&mparam);
gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
+#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+ /* This will break-before-make MMU for DDR */
+ update_early_mmu_table();
+#endif
return 0;
}
return 0;
}
-
-void dram_init_banksize(void)
-{
- /*
- * gd->arch.secure_ram tracks the location of secure memory.
- * It was set as if the memory starts from 0.
- * The address needs to add the offset of its bank.
- */
- gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
- if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
- gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
- gd->bd->bi_dram[1].size = gd->ram_size -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[1].start +
- gd->arch.secure_ram -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- } else {
- gd->bd->bi_dram[0].size = gd->ram_size;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[0].start +
- gd->arch.secure_ram;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- }
-}
#include <asm/arch/ppa.h>
#endif
#include <asm/arch/fdt.h>
+#include <asm/arch/mmu.h>
#include <asm/arch/soc.h>
#include <ahci.h>
#include <hwconfig.h>
mmdc_init(&mparam);
gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
+#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+ /* This will break-before-make MMU for DDR */
+ update_early_mmu_table();
+#endif
return 0;
}
return 0;
}
#endif
-
-void dram_init_banksize(void)
-{
- /*
- * gd->arch.secure_ram tracks the location of secure memory.
- * It was set as if the memory starts from 0.
- * The address needs to add the offset of its bank.
- */
- gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
- if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
- gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
- gd->bd->bi_dram[1].size = gd->ram_size -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[1].start +
- gd->arch.secure_ram -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- } else {
- gd->bd->bi_dram[0].size = gd->ram_size;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[0].start +
- gd->arch.secure_ram;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- }
-}
#ifdef CONFIG_FSL_LS_PPA
#include <asm/arch/ppa.h>
#endif
+#include <asm/arch/mmu.h>
#include <asm/arch/soc.h>
#include <hwconfig.h>
#include <ahci.h>
mmdc_init(&mparam);
gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
+#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+ /* This will break-before-make MMU for DDR */
+ update_early_mmu_table();
+#endif
return 0;
}
return 0;
}
-
-void dram_init_banksize(void)
-{
- /*
- * gd->secure_ram tracks the location of secure memory.
- * It was set as if the memory starts from 0.
- * The address needs to add the offset of its bank.
- */
- gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
- if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
- gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
- gd->bd->bi_dram[1].size = gd->ram_size -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[1].start +
- gd->arch.secure_ram -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- } else {
- gd->bd->bi_dram[0].size = gd->ram_size;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[0].start +
- gd->arch.secure_ram;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- }
-}
return dram_size;
}
-
-void dram_init_banksize(void)
-{
- /*
- * gd->arch.secure_ram tracks the location of secure memory.
- * It was set as if the memory starts from 0.
- * The address needs to add the offset of its bank.
- */
- gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
- if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
- gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
- gd->bd->bi_dram[1].size = gd->ram_size -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[1].start +
- gd->arch.secure_ram -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- } else {
- gd->bd->bi_dram[0].size = gd->ram_size;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[0].start +
- gd->arch.secure_ram;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- }
-}
#include <asm/arch/clock.h>
#include <asm/arch/fsl_serdes.h>
#include <asm/arch/fdt.h>
+#include <asm/arch/mmu.h>
#include <asm/arch/soc.h>
#include <ahci.h>
#include <hwconfig.h>
*/
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
gd->ram_size = initdram(0);
+#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+ /* This will break-before-make MMU for DDR */
+ update_early_mmu_table();
+#endif
return 0;
}
return dram_size;
}
-
-void dram_init_banksize(void)
-{
- /*
- * gd->arch.secure_ram tracks the location of secure memory.
- * It was set as if the memory starts from 0.
- * The address needs to add the offset of its bank.
- */
- gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
- if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
- gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
- gd->bd->bi_dram[1].size = gd->ram_size -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[1].start +
- gd->arch.secure_ram -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- } else {
- gd->bd->bi_dram[0].size = gd->ram_size;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[0].start +
- gd->arch.secure_ram;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- }
-}
return 0;
}
-int dram_init(void)
-{
- gd->ram_size = initdram(0);
-
- return 0;
-}
-
int board_early_init_f(void)
{
fsl_lsch2_early_init_f();
return dram_size;
}
-
-void dram_init_banksize(void)
-{
- /*
- * gd->arch.secure_ram tracks the location of secure memory.
- * It was set as if the memory starts from 0.
- * The address needs to add the offset of its bank.
- */
- gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
- if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
- gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
- gd->bd->bi_dram[1].size = gd->ram_size -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[1].start +
- gd->arch.secure_ram -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- } else {
- gd->bd->bi_dram[0].size = gd->ram_size;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[0].start +
- gd->arch.secure_ram;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- }
-}
#include <asm/arch/clock.h>
#include <asm/arch/fsl_serdes.h>
#include <asm/arch/fdt.h>
+#include <asm/arch/mmu.h>
#include <asm/arch/soc.h>
#include <ahci.h>
#include <hwconfig.h>
*/
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
gd->ram_size = initdram(0);
+#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+ /* This will break-before-make MMU for DDR */
+ update_early_mmu_table();
+#endif
return 0;
}
return dram_size;
}
-
-void dram_init_banksize(void)
-{
- /*
- * gd->arch.secure_ram tracks the location of secure memory.
- * It was set as if the memory starts from 0.
- * The address needs to add the offset of its bank.
- */
- gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
- if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
- gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
- gd->bd->bi_dram[1].size = gd->ram_size -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[1].start +
- gd->arch.secure_ram -
- CONFIG_SYS_DDR_BLOCK1_SIZE;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- } else {
- gd->bd->bi_dram[0].size = gd->ram_size;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[0].start +
- gd->arch.secure_ram;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- }
-}
return 0;
}
-int dram_init(void)
-{
- gd->ram_size = initdram(0);
-
- return 0;
-}
-
int board_early_init_f(void)
{
fsl_lsch2_early_init_f();
return dram_size;
}
-
-void dram_init_banksize(void)
-{
-#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
- phys_size_t dp_ddr_size;
-#endif
-
- /*
- * gd->arch.secure_ram tracks the location of secure memory.
- * It was set as if the memory starts from 0.
- * The address needs to add the offset of its bank.
- */
- gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
- if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
- gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
- gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
- gd->bd->bi_dram[1].size = gd->ram_size -
- CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[1].start +
- gd->arch.secure_ram -
- CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- } else {
- gd->bd->bi_dram[0].size = gd->ram_size;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[0].start +
- gd->arch.secure_ram;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- }
-
-#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
- if (soc_has_dp_ddr()) {
- /* initialize DP-DDR here */
- puts("DP-DDR: ");
- /*
- * DDR controller use 0 as the base address for binding.
- * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
- */
- dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
- CONFIG_DP_DDR_CTRL,
- CONFIG_DP_DDR_NUM_CTRLS,
- CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
- NULL, NULL, NULL);
- if (dp_ddr_size) {
- gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
- gd->bd->bi_dram[2].size = dp_ddr_size;
- } else {
- puts("Not detected");
- }
- }
-#endif
-}
#endif
}
-int dram_init(void)
-{
- gd->ram_size = initdram(0);
-
- return 0;
-}
-
#if defined(CONFIG_ARCH_MISC_INIT)
int arch_misc_init(void)
{
base[1] = gd->bd->bi_dram[1].start;
size[1] = gd->bd->bi_dram[1].size;
+#ifdef CONFIG_RESV_RAM
+ /* reduce size if reserved memory is within this bank */
+ if (gd->arch.resv_ram >= base[0] &&
+ gd->arch.resv_ram < base[0] + size[0])
+ size[0] = gd->arch.resv_ram - base[0];
+ else if (gd->arch.resv_ram >= base[1] &&
+ gd->arch.resv_ram < base[1] + size[1])
+ size[1] = gd->arch.resv_ram - base[1];
+#endif
+
fdt_fixup_memory_banks(blob, base, size, 2);
#ifdef CONFIG_FSL_MC_ENET
return dram_size;
}
-
-void dram_init_banksize(void)
-{
-#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
- phys_size_t dp_ddr_size;
-#endif
-
- /*
- * gd->arch.secure_ram tracks the location of secure memory.
- * It was set as if the memory starts from 0.
- * The address needs to add the offset of its bank.
- */
- gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
- if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
- gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
- gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
- gd->bd->bi_dram[1].size = gd->ram_size -
- CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[1].start +
- gd->arch.secure_ram -
- CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- } else {
- gd->bd->bi_dram[0].size = gd->ram_size;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[0].start +
- gd->arch.secure_ram;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- }
-
-#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
- if (soc_has_dp_ddr()) {
- /* initialize DP-DDR here */
- puts("DP-DDR: ");
- /*
- * DDR controller use 0 as the base address for binding.
- * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
- */
- dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
- CONFIG_DP_DDR_CTRL,
- CONFIG_DP_DDR_NUM_CTRLS,
- CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
- NULL, NULL, NULL);
- if (dp_ddr_size) {
- gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
- gd->bd->bi_dram[2].size = dp_ddr_size;
- } else {
- puts("Not detected");
- }
- }
-#endif
-}
#include "../common/qixis.h"
#include "ls2080aqds_qixis.h"
+#include "../common/vid.h"
#define PIN_MUX_SEL_SDHC 0x00
#define PIN_MUX_SEL_DSPI 0x0a
return 0;
}
+int misc_init_r(void)
+{
+ if (adjust_vdd(0))
+ printf("Warning: Adjusting core voltage failed.\n");
+
+ return 0;
+}
+
void detail_board_ddr_info(void)
{
puts("\nDDR ");
#endif
}
-int dram_init(void)
-{
- gd->ram_size = initdram(0);
-
- return 0;
-}
-
#if defined(CONFIG_ARCH_MISC_INIT)
int arch_misc_init(void)
{
base[1] = gd->bd->bi_dram[1].start;
size[1] = gd->bd->bi_dram[1].size;
+#ifdef CONFIG_RESV_RAM
+ /* reduce size if reserved memory is within this bank */
+ if (gd->arch.resv_ram >= base[0] &&
+ gd->arch.resv_ram < base[0] + size[0])
+ size[0] = gd->arch.resv_ram - base[0];
+ else if (gd->arch.resv_ram >= base[1] &&
+ gd->arch.resv_ram < base[1] + size[1])
+ size[1] = gd->arch.resv_ram - base[1];
+#endif
+
fdt_fixup_memory_banks(blob, base, size, 2);
fsl_fdt_fixup_dr_usb(blob, bd);
return dram_size;
}
-
-void dram_init_banksize(void)
-{
-#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
- phys_size_t dp_ddr_size;
-#endif
-
- /*
- * gd->arch.secure_ram tracks the location of secure memory.
- * It was set as if the memory starts from 0.
- * The address needs to add the offset of its bank.
- */
- gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
- if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
- gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
- gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
- gd->bd->bi_dram[1].size = gd->ram_size -
- CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[1].start +
- gd->arch.secure_ram -
- CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- } else {
- gd->bd->bi_dram[0].size = gd->ram_size;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- gd->arch.secure_ram = gd->bd->bi_dram[0].start +
- gd->arch.secure_ram;
- gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
- }
-
-#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
- if (soc_has_dp_ddr()) {
- /* initialize DP-DDR here */
- puts("DP-DDR: ");
- /*
- * DDR controller use 0 as the base address for binding.
- * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
- */
- dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
- CONFIG_DP_DDR_CTRL,
- CONFIG_DP_DDR_NUM_CTRLS,
- CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
- NULL, NULL, NULL);
- if (dp_ddr_size) {
- gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
- gd->bd->bi_dram[2].size = dp_ddr_size;
- } else {
- puts("Not detected");
- }
- }
-#endif
-}
#include <environment.h>
#include <efi_loader.h>
#include <i2c.h>
+#include <asm/arch/mmu.h>
#include <asm/arch/soc.h>
#include <fsl_sec.h>
if (adjust_vdd(0))
printf("Warning: Adjusting core voltage failed.\n");
-#if defined(CONFIG_EFI_LOADER) && !defined(CONFIG_SPL_BUILD)
- if (soc_has_dp_ddr() && gd->bd->bi_dram[2].size) {
- efi_add_memory_map(gd->bd->bi_dram[2].start,
- gd->bd->bi_dram[2].size >> EFI_PAGE_SHIFT,
- EFI_RESERVED_MEMORY_TYPE, false);
- }
-#endif
-
return 0;
}
#endif
}
-int dram_init(void)
-{
- gd->ram_size = initdram(0);
-
- return 0;
-}
-
#if defined(CONFIG_ARCH_MISC_INIT)
int arch_misc_init(void)
{
base[1] = gd->bd->bi_dram[1].start;
size[1] = gd->bd->bi_dram[1].size;
+#ifdef CONFIG_RESV_RAM
+ /* reduce size if reserved memory is within this bank */
+ if (gd->arch.resv_ram >= base[0] &&
+ gd->arch.resv_ram < base[0] + size[0])
+ size[0] = gd->arch.resv_ram - base[0];
+ else if (gd->arch.resv_ram >= base[1] &&
+ gd->arch.resv_ram < base[1] + size[1])
+ size[1] = gd->arch.resv_ram - base[1];
+#endif
+
fdt_fixup_memory_banks(blob, base, size, 2);
fsl_fdt_fixup_dr_usb(blob, bd);
.af = STM32_GPIO_AF0
};
-const struct stm32_gpio_ctl gpio_ctl_usart = {
- .mode = STM32_GPIO_MODE_AF,
- .otype = STM32_GPIO_OTYPE_PP,
- .speed = STM32_GPIO_SPEED_50M,
- .pupd = STM32_GPIO_PUPD_UP,
- .af = STM32_GPIO_AF7
-};
-
const struct stm32_gpio_ctl gpio_ctl_fmc = {
.mode = STM32_GPIO_MODE_AF,
.otype = STM32_GPIO_OTYPE_PP,
return rv;
}
-static const struct stm32_gpio_dsc usart_gpio[] = {
- {STM32_GPIO_PORT_A, STM32_GPIO_PIN_9}, /* TX */
- {STM32_GPIO_PORT_B, STM32_GPIO_PIN_7}, /* RX */
-};
-
int uart_setup_gpio(void)
{
- int i;
- int rv = 0;
-
clock_setup(GPIO_A_CLOCK_CFG);
clock_setup(GPIO_B_CLOCK_CFG);
- for (i = 0; i < ARRAY_SIZE(usart_gpio); i++) {
- rv = stm32_gpio_config(&usart_gpio[i], &gpio_ctl_usart);
- if (rv)
- goto out;
- }
-
-out:
- return rv;
+ return 0;
}
-static const struct stm32x7_serial_platdata serial_platdata = {
- .base = (struct stm32_usart *)USART1_BASE,
- .clock = CONFIG_SYS_CLK_FREQ,
-};
-
-U_BOOT_DEVICE(stm32x7_serials) = {
- .name = "serial_stm32x7",
- .platdata = &serial_platdata,
-};
-
#ifdef CONFIG_ETH_DESIGNWARE
-const struct stm32_gpio_ctl gpio_ctl_eth = {
- .mode = STM32_GPIO_MODE_AF,
- .otype = STM32_GPIO_OTYPE_PP,
- .speed = STM32_GPIO_SPEED_100M,
- .pupd = STM32_GPIO_PUPD_NO,
- .af = STM32_GPIO_AF11
-};
-
-static const struct stm32_gpio_dsc eth_gpio[] = {
- {STM32_GPIO_PORT_A, STM32_GPIO_PIN_1}, /* ETH_RMII_REF_CLK */
- {STM32_GPIO_PORT_A, STM32_GPIO_PIN_2}, /* ETH_MDIO */
- {STM32_GPIO_PORT_A, STM32_GPIO_PIN_7}, /* ETH_RMII_CRS_DV */
-
- {STM32_GPIO_PORT_C, STM32_GPIO_PIN_1}, /* ETH_MDC */
- {STM32_GPIO_PORT_C, STM32_GPIO_PIN_4}, /* ETH_RMII_RXD0 */
- {STM32_GPIO_PORT_C, STM32_GPIO_PIN_5}, /* ETH_RMII_RXD1 */
-
- {STM32_GPIO_PORT_G, STM32_GPIO_PIN_11}, /* ETH_RMII_TX_EN */
- {STM32_GPIO_PORT_G, STM32_GPIO_PIN_13}, /* ETH_RMII_TXD0 */
- {STM32_GPIO_PORT_G, STM32_GPIO_PIN_14}, /* ETH_RMII_TXD1 */
-};
static int stmmac_setup(void)
{
- int res = 0;
- int i;
-
clock_setup(SYSCFG_CLOCK_CFG);
-
/* Set >RMII mode */
STM32_SYSCFG->pmc |= SYSCFG_PMC_MII_RMII_SEL;
clock_setup(GPIO_A_CLOCK_CFG);
clock_setup(GPIO_C_CLOCK_CFG);
clock_setup(GPIO_G_CLOCK_CFG);
-
- for (i = 0; i < ARRAY_SIZE(eth_gpio); i++) {
- res = stm32_gpio_config(ð_gpio[i], &gpio_ctl_eth);
- if (res)
- return res;
- }
-
clock_setup(STMMAC_CLOCK_CFG);
return 0;
#endif
#ifdef CONFIG_STM32_QSPI
-const struct stm32_gpio_ctl gpio_ctl_qspi_9 = {
- .mode = STM32_GPIO_MODE_AF,
- .otype = STM32_GPIO_OTYPE_PP,
- .speed = STM32_GPIO_SPEED_100M,
- .pupd = STM32_GPIO_PUPD_NO,
- .af = STM32_GPIO_AF9
-};
-
-const struct stm32_gpio_ctl gpio_ctl_qspi_10 = {
- .mode = STM32_GPIO_MODE_AF,
- .otype = STM32_GPIO_OTYPE_PP,
- .speed = STM32_GPIO_SPEED_100M,
- .pupd = STM32_GPIO_PUPD_NO,
- .af = STM32_GPIO_AF10
-};
-
-static const struct stm32_gpio_dsc qspi_af9_gpio[] = {
- {STM32_GPIO_PORT_B, STM32_GPIO_PIN_2}, /* QUADSPI_CLK */
- {STM32_GPIO_PORT_D, STM32_GPIO_PIN_11}, /* QUADSPI_BK1_IO0 */
- {STM32_GPIO_PORT_D, STM32_GPIO_PIN_12}, /* QUADSPI_BK1_IO1 */
- {STM32_GPIO_PORT_D, STM32_GPIO_PIN_13}, /* QUADSPI_BK1_IO3 */
- {STM32_GPIO_PORT_E, STM32_GPIO_PIN_2}, /* QUADSPI_BK1_IO2 */
-};
-
-static const struct stm32_gpio_dsc qspi_af10_gpio[] = {
- {STM32_GPIO_PORT_B, STM32_GPIO_PIN_6}, /* QUADSPI_BK1_NCS */
-};
static int qspi_setup(void)
{
- int res = 0;
- int i;
-
clock_setup(GPIO_B_CLOCK_CFG);
clock_setup(GPIO_D_CLOCK_CFG);
clock_setup(GPIO_E_CLOCK_CFG);
-
- for (i = 0; i < ARRAY_SIZE(qspi_af9_gpio); i++) {
- res = stm32_gpio_config(&qspi_af9_gpio[i], &gpio_ctl_qspi_9);
- if (res)
- return res;
- }
-
- for (i = 0; i < ARRAY_SIZE(qspi_af10_gpio); i++) {
- res = stm32_gpio_config(&qspi_af10_gpio[i], &gpio_ctl_qspi_10);
- if (res)
- return res;
- }
-
return 0;
}
#endif
int res;
res = uart_setup_gpio();
- clock_setup(USART1_CLOCK_CFG);
if (res)
return res;
help
Compute CRC32.
+config CMD_MD5SUM
+ bool "md5sum"
+ default n
+ select MD5
+ help
+ Compute MD5 checksum.
+
+config MD5SUM_VERFIY
+ bool "md5sum -v"
+ default n
+ depends on CMD_MD5SUM
+ help
+ Add -v option to verify data against an MD5 checksum.
+
config LOOPW
bool "loopw"
help
gd->arch.secure_ram & MEM_RESERVE_SECURE_ADDR_MASK);
}
#endif
+#ifdef CONFIG_RESV_RAM
+ if (gd->arch.resv_ram)
+ print_num("Reserved ram", gd->arch.resv_ram);
+#endif
#if defined(CONFIG_CMD_NET) && !defined(CONFIG_DM_ETH)
print_eths();
#endif
if (e == NULL) {
#ifdef CONFIG_RANDOM_UUID
debug("%s unset. ", str);
- gen_rand_uuid_str(uuid_str, UUID_STR_FORMAT_STD);
+ gen_rand_uuid_str(uuid_str, UUID_STR_FORMAT_GUID);
setenv(s, uuid_str);
e = getenv(s);
l = simple_strtoul(s, NULL, 16);
}
- return l & ((1UL << (w * 8)) - 1);
+ /* avoid overflow on mask calculus */
+ return (w >= sizeof(long)) ? l : (l & ((1UL << (w * 8)) - 1));
}
static char * evalstr(char *s)
return gd->ram_top;
}
-__weak phys_size_t board_reserve_ram_top(phys_size_t ram_size)
-{
-#ifdef CONFIG_SYS_MEM_TOP_HIDE
- return ram_size - CONFIG_SYS_MEM_TOP_HIDE;
-#else
- return ram_size;
-#endif
-}
-
static int setup_dest_addr(void)
{
debug("Monitor len: %08lX\n", gd->mon_len);
* Ram is setup, size stored in gd !!
*/
debug("Ram size: %08lX\n", (ulong)gd->ram_size);
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
- /* Reserve memory for secure MMU tables, and/or security monitor */
- gd->ram_size -= CONFIG_SYS_MEM_RESERVE_SECURE;
- /*
- * Record secure memory location. Need recalcuate if memory splits
- * into banks, or the ram base is not zero.
- */
- gd->arch.secure_ram = gd->ram_size;
-#endif
+#if defined(CONFIG_SYS_MEM_TOP_HIDE)
/*
* Subtract specified amount of memory to hide so that it won't
* get "touched" at all by U-Boot. By fixing up gd->ram_size
* the Linux kernel should now get passed the now "corrected"
- * memory size and won't touch it either. This has been used
- * by arch/powerpc exclusively. Now ARMv8 takes advantage of
- * thie mechanism. If memory is split into banks, addresses
- * need to be calculated.
+ * memory size and won't touch it either. This should work
+ * for arch/ppc and arch/powerpc. Only Linux board ports in
+ * arch/powerpc with bootwrapper support, that recalculate the
+ * memory size from the SDRAM controller setup will have to
+ * get fixed.
*/
- gd->ram_size = board_reserve_ram_top(gd->ram_size);
-
+ gd->ram_size -= CONFIG_SYS_MEM_TOP_HIDE;
+#endif
#ifdef CONFIG_SYS_SDRAM_BASE
gd->ram_top = CONFIG_SYS_SDRAM_BASE;
#endif
CONFIG_USB_ULPI_VIEWPORT=y
CONFIG_USB_ULPI=y
CONFIG_USB_STORAGE=y
+CONFIG_CMD_MD5SUM=y
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_ASKENV=y
CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MD5SUM=y
CONFIG_LOOPW=y
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_MX_CYCLIC=y
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_ASKENV=y
CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MD5SUM=y
CONFIG_LOOPW=y
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_MX_CYCLIC=y
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_ASKENV=y
CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MD5SUM=y
CONFIG_LOOPW=y
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_MX_CYCLIC=y
CONFIG_MAC_PARTITION=y
CONFIG_DOS_PARTITION=y
CONFIG_MMC=y
+CONFIG_CMD_MD5SUM=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_MAC_PARTITION=y
CONFIG_DOS_PARTITION=y
CONFIG_MMC=y
+CONFIG_CMD_MD5SUM=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_MAC_PARTITION=y
CONFIG_DOS_PARTITION=y
CONFIG_MMC=y
+CONFIG_CMD_MD5SUM=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_USE_PRIVATE_LIBGCC=y
CONFIG_STM32_QSPI=y
CONFIG_OF_LIBFDT_OVERLAY=y
# CONFIG_EFI_LOADER is not set
+CONFIG_CLK=y
+CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_FULL is not set
+CONFIG_PINCTRL_STM32=y
str_uuid = partitions[i].uuid;
bin_uuid = gpt_e[i].unique_partition_guid.b;
- if (uuid_str_to_bin(str_uuid, bin_uuid, UUID_STR_FORMAT_STD)) {
+ if (uuid_str_to_bin(str_uuid, bin_uuid, UUID_STR_FORMAT_GUID)) {
printf("Partition no. %d: invalid guid: %s\n",
i, str_uuid);
return -1;
--- /dev/null
+STMicroelectronics STM32 Reset and Clock Controller
+===================================================
+
+The RCC IP is both a reset and a clock controller.
+
+Please refer to clock-bindings.txt for common clock controller binding usage.
+Please also refer to reset.txt for common reset controller binding usage.
+
+Required properties:
+- compatible: Should be:
+ "st,stm32f42xx-rcc"
+ "st,stm32f469-rcc"
+- reg: should be register base and length as documented in the
+ datasheet
+- #reset-cells: 1, see below
+- #clock-cells: 2, device nodes should specify the clock in their "clocks"
+ property, containing a phandle to the clock device node, an index selecting
+ between gated clocks and other clocks and an index specifying the clock to
+ use.
+
+Example:
+
+ rcc: rcc@40023800 {
+ #reset-cells = <1>;
+ #clock-cells = <2>
+ compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
+ reg = <0x40023800 0x400>;
+ };
+
+Specifying gated clocks
+=======================
+
+The primary index must be set to 0.
+
+The secondary index is the bit number within the RCC register bank, starting
+from the first RCC clock enable register (RCC_AHB1ENR, address offset 0x30).
+
+It is calculated as: index = register_offset / 4 * 32 + bit_offset.
+Where bit_offset is the bit offset within the register (LSB is 0, MSB is 31).
+
+To simplify the usage and to share bit definition with the reset and clock
+drivers of the RCC IP, macros are available to generate the index in
+human-readble format.
+
+For STM32F4 series, the macro are available here:
+ - include/dt-bindings/mfd/stm32f4-rcc.h
+
+Example:
+
+ /* Gated clock, AHB1 bit 0 (GPIOA) */
+ ... {
+ clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOA)>
+ };
+
+ /* Gated clock, AHB2 bit 4 (CRYP) */
+ ... {
+ clocks = <&rcc 0 STM32F4_AHB2_CLOCK(CRYP)>
+ };
+
+Specifying other clocks
+=======================
+
+The primary index must be set to 1.
+
+The secondary index is bound with the following magic numbers:
+
+ 0 SYSTICK
+ 1 FCLK
+
+Example:
+
+ /* Misc clock, FCLK */
+ ... {
+ clocks = <&rcc 1 STM32F4_APB1_CLOCK(TIM2)>
+ };
+
+
+Specifying softreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the reset device node and an index specifying
+which channel to use.
+The index is the bit number within the RCC registers bank, starting from RCC
+base address.
+It is calculated as: index = register_offset / 4 * 32 + bit_offset.
+Where bit_offset is the bit offset within the register.
+For example, for CRC reset:
+ crc = AHB1RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x10 / 4 * 32 + 12 = 140
+
+example:
+
+ timer2 {
+ resets = <&rcc STM32F4_APB1_RESET(TIM2)>;
+ };
--- /dev/null
+* STM32 GPIO and Pin Mux/Config controller
+
+STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware
+controller. It controls the input/output settings on the available pins and
+also provides ability to multiplex and configure the output of various on-chip
+controllers onto these pads.
+
+Pin controller node:
+Required properies:
+ - compatible: value should be one of the following:
+ (a) "st,stm32f429-pinctrl"
+ (b) "st,stm32f746-pinctrl"
+ - #address-cells: The value of this property must be 1
+ - #size-cells : The value of this property must be 1
+ - ranges : defines mapping between pin controller node (parent) to
+ gpio-bank node (children).
+ - pins-are-numbered: Specify the subnodes are using numbered pinmux to
+ specify pins.
+
+GPIO controller/bank node:
+Required properties:
+ - gpio-controller : Indicates this device is a GPIO controller
+ - #gpio-cells : Should be two.
+ The first cell is the pin number
+ The second one is the polarity:
+ - 0 for active high
+ - 1 for active low
+ - reg : The gpio address range, relative to the pinctrl range
+ - clocks : clock that drives this bank
+ - st,bank-name : Should be a name string for this bank as specified in
+ the datasheet
+
+Optional properties:
+ - reset: : Reference to the reset controller
+ - interrupt-parent: phandle of the interrupt parent to which the external
+ GPIO interrupts are forwarded to.
+ - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
+ which includes IRQ mux selection register, and the offset of the IRQ mux
+ selection register.
+
+Example:
+#include <dt-bindings/pinctrl/stm32f429-pinfunc.h>
+...
+
+ pin-controller {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,stm32f429-pinctrl";
+ ranges = <0 0x40020000 0x3000>;
+ pins-are-numbered;
+
+ gpioa: gpio@40020000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x0 0x400>;
+ resets = <&reset_ahb1 0>;
+ st,bank-name = "GPIOA";
+ };
+ ...
+ pin-functions nodes follow...
+ };
+
+Contents of function subnode node:
+----------------------------------
+Subnode format
+A pinctrl node should contain at least one subnode representing the
+pinctrl group available on the machine. Each subnode will list the
+pins it needs, and how they should be configured, with regard to muxer
+configuration, pullups, drive, output high/low and output speed.
+
+ node {
+ pinmux = <PIN_NUMBER_PINMUX>;
+ GENERIC_PINCONFIG;
+ };
+
+Required properties:
+- pinmux: integer array, represents gpio pin number and mux setting.
+ Supported pin number and mux varies for different SoCs, and are defined in
+ dt-bindings/pinctrl/<soc>-pinfunc.h directly.
+ These defines are calculated as:
+ ((port * 16 + line) << 8) | function
+ With:
+ - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11)
+ - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15)
+ - function: The function number, can be:
+ * 0 : GPIO IN
+ * 1 : Alternate Function 0
+ * 2 : Alternate Function 1
+ * 3 : Alternate Function 2
+ * ...
+ * 16 : Alternate Function 15
+ * 17 : Analog
+ * 18 : GPIO OUT
+
+Optional properties:
+- GENERIC_PINCONFIG: is the generic pinconfig options to use.
+ Available options are:
+ - bias-disable,
+ - bias-pull-down,
+ - bias-pull-up,
+ - drive-push-pull,
+ - drive-open-drain,
+ - output-low
+ - output-high
+ - slew-rate = <x>, with x being:
+ < 0 > : Low speed
+ < 1 > : Medium speed
+ < 2 > : Fast speed
+ < 3 > : High speed
+
+Example:
+
+pin-controller {
+...
+ usart1_pins_a: usart1@0 {
+ pins1 {
+ pinmux = <STM32F429_PA9_FUNC_USART1_TX>;
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32F429_PA10_FUNC_USART1_RX>;
+ bias-disable;
+ };
+ };
+};
+
+&usart1 {
+ pinctrl-0 = <&usart1_pins_a>;
+ pinctrl-names = "default";
+ status = "okay";
+};
help
Enable this to support the clocks
+config CLK_ZYNQ
+ bool "Enable clock driver support for Zynq"
+ depends on CLK && ARCH_ZYNQ
+ default y
+ help
+ This clock driver adds support for clock realted settings for
+ Zynq platform.
+
config CLK_ZYNQMP
bool "Enable clock driver support for ZynqMP"
depends on ARCH_ZYNQMP
obj-$(CONFIG_SANDBOX) += clk_sandbox.o
obj-$(CONFIG_SANDBOX) += clk_sandbox_test.o
obj-$(CONFIG_MACH_PIC32) += clk_pic32.o
+obj-$(CONFIG_CLK_ZYNQ) += clk_zynq.o
obj-$(CONFIG_CLK_ZYNQMP) += clk_zynqmp.o
obj-y += tegra/
obj-$(CONFIG_CLK_EXYNOS) += exynos/
obj-$(CONFIG_CLK_AT91) += at91/
obj-$(CONFIG_CLK_BOSTON) += clk_boston.o
-
obj-$(CONFIG_ARCH_ASPEED) += aspeed/
+obj-$(CONFIG_STM32F7) += clk_stm32f7.o
--- /dev/null
+/*
+ * (C) Copyright 2017
+ * Vikas Manocha, <vikas.manocha@st.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <clk-uclass.h>
+#include <dm.h>
+#include <asm/io.h>
+#include <asm/arch/rcc.h>
+#include <asm/arch/stm32.h>
+#include <asm/arch/stm32_periph.h>
+
+#define RCC_CR_HSION BIT(0)
+#define RCC_CR_HSEON BIT(16)
+#define RCC_CR_HSERDY BIT(17)
+#define RCC_CR_HSEBYP BIT(18)
+#define RCC_CR_CSSON BIT(19)
+#define RCC_CR_PLLON BIT(24)
+#define RCC_CR_PLLRDY BIT(25)
+
+#define RCC_PLLCFGR_PLLM_MASK GENMASK(5, 0)
+#define RCC_PLLCFGR_PLLN_MASK GENMASK(14, 6)
+#define RCC_PLLCFGR_PLLP_MASK GENMASK(17, 16)
+#define RCC_PLLCFGR_PLLQ_MASK GENMASK(27, 24)
+#define RCC_PLLCFGR_PLLSRC BIT(22)
+#define RCC_PLLCFGR_PLLM_SHIFT 0
+#define RCC_PLLCFGR_PLLN_SHIFT 6
+#define RCC_PLLCFGR_PLLP_SHIFT 16
+#define RCC_PLLCFGR_PLLQ_SHIFT 24
+
+#define RCC_CFGR_AHB_PSC_MASK GENMASK(7, 4)
+#define RCC_CFGR_APB1_PSC_MASK GENMASK(12, 10)
+#define RCC_CFGR_APB2_PSC_MASK GENMASK(15, 13)
+#define RCC_CFGR_SW0 BIT(0)
+#define RCC_CFGR_SW1 BIT(1)
+#define RCC_CFGR_SW_MASK GENMASK(1, 0)
+#define RCC_CFGR_SW_HSI 0
+#define RCC_CFGR_SW_HSE RCC_CFGR_SW0
+#define RCC_CFGR_SW_PLL RCC_CFGR_SW1
+#define RCC_CFGR_SWS0 BIT(2)
+#define RCC_CFGR_SWS1 BIT(3)
+#define RCC_CFGR_SWS_MASK GENMASK(3, 2)
+#define RCC_CFGR_SWS_HSI 0
+#define RCC_CFGR_SWS_HSE RCC_CFGR_SWS0
+#define RCC_CFGR_SWS_PLL RCC_CFGR_SWS1
+#define RCC_CFGR_HPRE_SHIFT 4
+#define RCC_CFGR_PPRE1_SHIFT 10
+#define RCC_CFGR_PPRE2_SHIFT 13
+
+/*
+ * Offsets of some PWR registers
+ */
+#define PWR_CR1_ODEN BIT(16)
+#define PWR_CR1_ODSWEN BIT(17)
+#define PWR_CSR1_ODRDY BIT(16)
+#define PWR_CSR1_ODSWRDY BIT(17)
+
+struct pll_psc {
+ u8 pll_m;
+ u16 pll_n;
+ u8 pll_p;
+ u8 pll_q;
+ u8 ahb_psc;
+ u8 apb1_psc;
+ u8 apb2_psc;
+};
+
+#define AHB_PSC_1 0
+#define AHB_PSC_2 0x8
+#define AHB_PSC_4 0x9
+#define AHB_PSC_8 0xA
+#define AHB_PSC_16 0xB
+#define AHB_PSC_64 0xC
+#define AHB_PSC_128 0xD
+#define AHB_PSC_256 0xE
+#define AHB_PSC_512 0xF
+
+#define APB_PSC_1 0
+#define APB_PSC_2 0x4
+#define APB_PSC_4 0x5
+#define APB_PSC_8 0x6
+#define APB_PSC_16 0x7
+
+#if !defined(CONFIG_STM32_HSE_HZ)
+#error "CONFIG_STM32_HSE_HZ not defined!"
+#else
+#if (CONFIG_STM32_HSE_HZ == 25000000)
+#if (CONFIG_SYS_CLK_FREQ == 200000000)
+/* 200 MHz */
+struct pll_psc sys_pll_psc = {
+ .pll_m = 25,
+ .pll_n = 400,
+ .pll_p = 2,
+ .pll_q = 8,
+ .ahb_psc = AHB_PSC_1,
+ .apb1_psc = APB_PSC_4,
+ .apb2_psc = APB_PSC_2
+};
+#endif
+#else
+#error "No PLL/Prescaler configuration for given CONFIG_STM32_HSE_HZ exists"
+#endif
+#endif
+
+int configure_clocks(void)
+{
+ /* Reset RCC configuration */
+ setbits_le32(&STM32_RCC->cr, RCC_CR_HSION);
+ writel(0, &STM32_RCC->cfgr); /* Reset CFGR */
+ clrbits_le32(&STM32_RCC->cr, (RCC_CR_HSEON | RCC_CR_CSSON
+ | RCC_CR_PLLON));
+ writel(0x24003010, &STM32_RCC->pllcfgr); /* Reset value from RM */
+ clrbits_le32(&STM32_RCC->cr, RCC_CR_HSEBYP);
+ writel(0, &STM32_RCC->cir); /* Disable all interrupts */
+
+ /* Configure for HSE+PLL operation */
+ setbits_le32(&STM32_RCC->cr, RCC_CR_HSEON);
+ while (!(readl(&STM32_RCC->cr) & RCC_CR_HSERDY))
+ ;
+
+ setbits_le32(&STM32_RCC->cfgr, ((
+ sys_pll_psc.ahb_psc << RCC_CFGR_HPRE_SHIFT)
+ | (sys_pll_psc.apb1_psc << RCC_CFGR_PPRE1_SHIFT)
+ | (sys_pll_psc.apb2_psc << RCC_CFGR_PPRE2_SHIFT)));
+
+ /* Configure the main PLL */
+ uint32_t pllcfgr = 0;
+ pllcfgr = RCC_PLLCFGR_PLLSRC; /* pll source HSE */
+ pllcfgr |= sys_pll_psc.pll_m << RCC_PLLCFGR_PLLM_SHIFT;
+ pllcfgr |= sys_pll_psc.pll_n << RCC_PLLCFGR_PLLN_SHIFT;
+ pllcfgr |= ((sys_pll_psc.pll_p >> 1) - 1) << RCC_PLLCFGR_PLLP_SHIFT;
+ pllcfgr |= sys_pll_psc.pll_q << RCC_PLLCFGR_PLLQ_SHIFT;
+ writel(pllcfgr, &STM32_RCC->pllcfgr);
+
+ /* Enable the main PLL */
+ setbits_le32(&STM32_RCC->cr, RCC_CR_PLLON);
+ while (!(readl(&STM32_RCC->cr) & RCC_CR_PLLRDY))
+ ;
+
+ /* Enable high performance mode, System frequency up to 200 MHz */
+ setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_PWREN);
+ setbits_le32(&STM32_PWR->cr1, PWR_CR1_ODEN);
+ /* Infinite wait! */
+ while (!(readl(&STM32_PWR->csr1) & PWR_CSR1_ODRDY))
+ ;
+ /* Enable the Over-drive switch */
+ setbits_le32(&STM32_PWR->cr1, PWR_CR1_ODSWEN);
+ /* Infinite wait! */
+ while (!(readl(&STM32_PWR->csr1) & PWR_CSR1_ODSWRDY))
+ ;
+
+ stm32_flash_latency_cfg(5);
+ clrbits_le32(&STM32_RCC->cfgr, (RCC_CFGR_SW0 | RCC_CFGR_SW1));
+ setbits_le32(&STM32_RCC->cfgr, RCC_CFGR_SW_PLL);
+
+ while ((readl(&STM32_RCC->cfgr) & RCC_CFGR_SWS_MASK) !=
+ RCC_CFGR_SWS_PLL)
+ ;
+
+ return 0;
+}
+
+unsigned long clock_get(enum clock clck)
+{
+ u32 sysclk = 0;
+ u32 shift = 0;
+ /* Prescaler table lookups for clock computation */
+ u8 ahb_psc_table[16] = {
+ 0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9
+ };
+ u8 apb_psc_table[8] = {
+ 0, 0, 0, 0, 1, 2, 3, 4
+ };
+
+ if ((readl(&STM32_RCC->cfgr) & RCC_CFGR_SWS_MASK) ==
+ RCC_CFGR_SWS_PLL) {
+ u16 pllm, plln, pllp;
+ pllm = (readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLM_MASK);
+ plln = ((readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLN_MASK)
+ >> RCC_PLLCFGR_PLLN_SHIFT);
+ pllp = ((((readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLP_MASK)
+ >> RCC_PLLCFGR_PLLP_SHIFT) + 1) << 1);
+ sysclk = ((CONFIG_STM32_HSE_HZ / pllm) * plln) / pllp;
+ }
+
+ switch (clck) {
+ case CLOCK_CORE:
+ return sysclk;
+ break;
+ case CLOCK_AHB:
+ shift = ahb_psc_table[(
+ (readl(&STM32_RCC->cfgr) & RCC_CFGR_AHB_PSC_MASK)
+ >> RCC_CFGR_HPRE_SHIFT)];
+ return sysclk >>= shift;
+ break;
+ case CLOCK_APB1:
+ shift = apb_psc_table[(
+ (readl(&STM32_RCC->cfgr) & RCC_CFGR_APB1_PSC_MASK)
+ >> RCC_CFGR_PPRE1_SHIFT)];
+ return sysclk >>= shift;
+ break;
+ case CLOCK_APB2:
+ shift = apb_psc_table[(
+ (readl(&STM32_RCC->cfgr) & RCC_CFGR_APB2_PSC_MASK)
+ >> RCC_CFGR_PPRE2_SHIFT)];
+ return sysclk >>= shift;
+ break;
+ default:
+ return 0;
+ break;
+ }
+}
+
+static int stm32_clk_enable(struct clk *clk)
+{
+ u32 offset = clk->id / 32;
+ u32 bit_index = clk->id % 32;
+
+ debug("%s: clkid = %ld, offset from AHB1ENR is %d, bit_index = %d\n",
+ __func__, clk->id, offset, bit_index);
+ setbits_le32(&STM32_RCC->ahb1enr + offset, BIT(bit_index));
+
+ return 0;
+}
+
+void clock_setup(int peripheral)
+{
+ switch (peripheral) {
+ case GPIO_A_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_A_EN);
+ break;
+ case GPIO_B_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_B_EN);
+ break;
+ case GPIO_C_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_C_EN);
+ break;
+ case GPIO_D_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_D_EN);
+ break;
+ case GPIO_E_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_E_EN);
+ break;
+ case GPIO_F_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_F_EN);
+ break;
+ case GPIO_G_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_G_EN);
+ break;
+ case GPIO_H_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_H_EN);
+ break;
+ case GPIO_I_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_I_EN);
+ break;
+ case GPIO_J_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_J_EN);
+ break;
+ case GPIO_K_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_K_EN);
+ break;
+ case SYSCFG_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->apb2enr, RCC_APB2ENR_SYSCFGEN);
+ break;
+ case TIMER2_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_TIM2EN);
+ break;
+ case FMC_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_FMC_EN);
+ break;
+ case STMMAC_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_EN);
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_RX_EN);
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_TX_EN);
+ break;
+ case QSPI_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_QSPI_EN);
+ break;
+ default:
+ break;
+ }
+}
+
+static int stm32_clk_probe(struct udevice *dev)
+{
+ debug("%s: stm32_clk_probe\n", __func__);
+ configure_clocks();
+
+ return 0;
+}
+
+static int stm32_clk_of_xlate(struct clk *clk,
+ struct fdtdec_phandle_args *args)
+{
+ debug("%s(clk=%p)\n", __func__, clk);
+
+ if (args->args_count != 2) {
+ debug("Invaild args_count: %d\n", args->args_count);
+ return -EINVAL;
+ }
+
+ if (args->args_count)
+ clk->id = args->args[1];
+ else
+ clk->id = 0;
+
+ return 0;
+}
+
+static struct clk_ops stm32_clk_ops = {
+ .of_xlate = stm32_clk_of_xlate,
+ .enable = stm32_clk_enable,
+};
+
+static const struct udevice_id stm32_clk_ids[] = {
+ { .compatible = "st,stm32f42xx-rcc"},
+ {}
+};
+
+U_BOOT_DRIVER(stm32f7_clk) = {
+ .name = "stm32f7_clk",
+ .id = UCLASS_CLK,
+ .of_match = stm32_clk_ids,
+ .ops = &stm32_clk_ops,
+ .probe = stm32_clk_probe,
+ .flags = DM_FLAG_PRE_RELOC,
+};
--- /dev/null
+/*
+ * Copyright (C) 2017 Weidmüller Interface GmbH & Co. KG
+ * Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
+ *
+ * Copyright (C) 2013 Soren Brinkmann <soren.brinkmann@xilinx.com>
+ * Copyright (C) 2013 Xilinx, Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <clk-uclass.h>
+#include <dm.h>
+#include <dm/lists.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
+
+/* Register bitfield defines */
+#define PLLCTRL_FBDIV_MASK 0x7f000
+#define PLLCTRL_FBDIV_SHIFT 12
+#define PLLCTRL_BPFORCE_MASK (1 << 4)
+#define PLLCTRL_PWRDWN_MASK 2
+#define PLLCTRL_PWRDWN_SHIFT 1
+#define PLLCTRL_RESET_MASK 1
+#define PLLCTRL_RESET_SHIFT 0
+
+#define ZYNQ_CLK_MAXDIV 0x3f
+#define CLK_CTRL_DIV1_SHIFT 20
+#define CLK_CTRL_DIV1_MASK (ZYNQ_CLK_MAXDIV << CLK_CTRL_DIV1_SHIFT)
+#define CLK_CTRL_DIV0_SHIFT 8
+#define CLK_CTRL_DIV0_MASK (ZYNQ_CLK_MAXDIV << CLK_CTRL_DIV0_SHIFT)
+#define CLK_CTRL_SRCSEL_SHIFT 4
+#define CLK_CTRL_SRCSEL_MASK (0x3 << CLK_CTRL_SRCSEL_SHIFT)
+
+#define CLK_CTRL_DIV2X_SHIFT 26
+#define CLK_CTRL_DIV2X_MASK (ZYNQ_CLK_MAXDIV << CLK_CTRL_DIV2X_SHIFT)
+#define CLK_CTRL_DIV3X_SHIFT 20
+#define CLK_CTRL_DIV3X_MASK (ZYNQ_CLK_MAXDIV << CLK_CTRL_DIV3X_SHIFT)
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_SPL_BUILD
+enum zynq_clk_rclk {mio_clk, emio_clk};
+#endif
+
+struct zynq_clk_priv {
+ ulong ps_clk_freq;
+#ifndef CONFIG_SPL_BUILD
+ struct clk gem_emio_clk[2];
+#endif
+};
+
+static void *zynq_clk_get_register(enum zynq_clk id)
+{
+ switch (id) {
+ case armpll_clk:
+ return &slcr_base->arm_pll_ctrl;
+ case ddrpll_clk:
+ return &slcr_base->ddr_pll_ctrl;
+ case iopll_clk:
+ return &slcr_base->io_pll_ctrl;
+ case lqspi_clk:
+ return &slcr_base->lqspi_clk_ctrl;
+ case smc_clk:
+ return &slcr_base->smc_clk_ctrl;
+ case pcap_clk:
+ return &slcr_base->pcap_clk_ctrl;
+ case sdio0_clk ... sdio1_clk:
+ return &slcr_base->sdio_clk_ctrl;
+ case uart0_clk ... uart1_clk:
+ return &slcr_base->uart_clk_ctrl;
+ case spi0_clk ... spi1_clk:
+ return &slcr_base->spi_clk_ctrl;
+#ifndef CONFIG_SPL_BUILD
+ case dci_clk:
+ return &slcr_base->dci_clk_ctrl;
+ case gem0_clk:
+ return &slcr_base->gem0_clk_ctrl;
+ case gem1_clk:
+ return &slcr_base->gem1_clk_ctrl;
+ case fclk0_clk:
+ return &slcr_base->fpga0_clk_ctrl;
+ case fclk1_clk:
+ return &slcr_base->fpga1_clk_ctrl;
+ case fclk2_clk:
+ return &slcr_base->fpga2_clk_ctrl;
+ case fclk3_clk:
+ return &slcr_base->fpga3_clk_ctrl;
+ case can0_clk ... can1_clk:
+ return &slcr_base->can_clk_ctrl;
+ case dbg_trc_clk ... dbg_apb_clk:
+ /* fall through */
+#endif
+ default:
+ return &slcr_base->dbg_clk_ctrl;
+ }
+}
+
+static enum zynq_clk zynq_clk_get_cpu_pll(u32 clk_ctrl)
+{
+ u32 srcsel = (clk_ctrl & CLK_CTRL_SRCSEL_MASK) >> CLK_CTRL_SRCSEL_SHIFT;
+
+ switch (srcsel) {
+ case 2:
+ return ddrpll_clk;
+ case 3:
+ return iopll_clk;
+ case 0 ... 1:
+ default:
+ return armpll_clk;
+ }
+}
+
+static enum zynq_clk zynq_clk_get_peripheral_pll(u32 clk_ctrl)
+{
+ u32 srcsel = (clk_ctrl & CLK_CTRL_SRCSEL_MASK) >> CLK_CTRL_SRCSEL_SHIFT;
+
+ switch (srcsel) {
+ case 2:
+ return armpll_clk;
+ case 3:
+ return ddrpll_clk;
+ case 0 ... 1:
+ default:
+ return iopll_clk;
+ }
+}
+
+static ulong zynq_clk_get_pll_rate(struct zynq_clk_priv *priv, enum zynq_clk id)
+{
+ u32 clk_ctrl, reset, pwrdwn, mul, bypass;
+
+ clk_ctrl = readl(zynq_clk_get_register(id));
+
+ reset = (clk_ctrl & PLLCTRL_RESET_MASK) >> PLLCTRL_RESET_SHIFT;
+ pwrdwn = (clk_ctrl & PLLCTRL_PWRDWN_MASK) >> PLLCTRL_PWRDWN_SHIFT;
+ if (reset || pwrdwn)
+ return 0;
+
+ bypass = clk_ctrl & PLLCTRL_BPFORCE_MASK;
+ if (bypass)
+ mul = 1;
+ else
+ mul = (clk_ctrl & PLLCTRL_FBDIV_MASK) >> PLLCTRL_FBDIV_SHIFT;
+
+ return priv->ps_clk_freq * mul;
+}
+
+#ifndef CONFIG_SPL_BUILD
+static enum zynq_clk_rclk zynq_clk_get_gem_rclk(enum zynq_clk id)
+{
+ u32 clk_ctrl, srcsel;
+
+ if (id == gem0_clk)
+ clk_ctrl = readl(&slcr_base->gem0_rclk_ctrl);
+ else
+ clk_ctrl = readl(&slcr_base->gem1_rclk_ctrl);
+
+ srcsel = (clk_ctrl & CLK_CTRL_SRCSEL_MASK) >> CLK_CTRL_SRCSEL_SHIFT;
+ if (srcsel)
+ return emio_clk;
+ else
+ return mio_clk;
+}
+#endif
+
+static ulong zynq_clk_get_cpu_rate(struct zynq_clk_priv *priv, enum zynq_clk id)
+{
+ u32 clk_621, clk_ctrl, div;
+ enum zynq_clk pll;
+
+ clk_ctrl = readl(&slcr_base->arm_clk_ctrl);
+
+ div = (clk_ctrl & CLK_CTRL_DIV0_MASK) >> CLK_CTRL_DIV0_SHIFT;
+
+ switch (id) {
+ case cpu_1x_clk:
+ div *= 2;
+ /* fall through */
+ case cpu_2x_clk:
+ clk_621 = readl(&slcr_base->clk_621_true) & 1;
+ div *= 2 + clk_621;
+ break;
+ case cpu_3or2x_clk:
+ div *= 2;
+ /* fall through */
+ case cpu_6or4x_clk:
+ break;
+ default:
+ return 0;
+ }
+
+ pll = zynq_clk_get_cpu_pll(clk_ctrl);
+
+ return DIV_ROUND_CLOSEST(zynq_clk_get_pll_rate(priv, pll), div);
+}
+
+#ifndef CONFIG_SPL_BUILD
+static ulong zynq_clk_get_ddr2x_rate(struct zynq_clk_priv *priv)
+{
+ u32 clk_ctrl, div;
+
+ clk_ctrl = readl(&slcr_base->ddr_clk_ctrl);
+
+ div = (clk_ctrl & CLK_CTRL_DIV2X_MASK) >> CLK_CTRL_DIV2X_SHIFT;
+
+ return DIV_ROUND_CLOSEST(zynq_clk_get_pll_rate(priv, ddrpll_clk), div);
+}
+#endif
+
+static ulong zynq_clk_get_ddr3x_rate(struct zynq_clk_priv *priv)
+{
+ u32 clk_ctrl, div;
+
+ clk_ctrl = readl(&slcr_base->ddr_clk_ctrl);
+
+ div = (clk_ctrl & CLK_CTRL_DIV3X_MASK) >> CLK_CTRL_DIV3X_SHIFT;
+
+ return DIV_ROUND_CLOSEST(zynq_clk_get_pll_rate(priv, ddrpll_clk), div);
+}
+
+#ifndef CONFIG_SPL_BUILD
+static ulong zynq_clk_get_dci_rate(struct zynq_clk_priv *priv)
+{
+ u32 clk_ctrl, div0, div1;
+
+ clk_ctrl = readl(&slcr_base->dci_clk_ctrl);
+
+ div0 = (clk_ctrl & CLK_CTRL_DIV0_MASK) >> CLK_CTRL_DIV0_SHIFT;
+ div1 = (clk_ctrl & CLK_CTRL_DIV1_MASK) >> CLK_CTRL_DIV1_SHIFT;
+
+ return DIV_ROUND_CLOSEST(DIV_ROUND_CLOSEST(
+ zynq_clk_get_pll_rate(priv, ddrpll_clk), div0), div1);
+}
+#endif
+
+static ulong zynq_clk_get_peripheral_rate(struct zynq_clk_priv *priv,
+ enum zynq_clk id, bool two_divs)
+{
+ enum zynq_clk pll;
+ u32 clk_ctrl, div0;
+ u32 div1 = 1;
+
+ clk_ctrl = readl(zynq_clk_get_register(id));
+
+ div0 = (clk_ctrl & CLK_CTRL_DIV0_MASK) >> CLK_CTRL_DIV0_SHIFT;
+ if (!div0)
+ div0 = 1;
+
+#ifndef CONFIG_SPL_BUILD
+ if (two_divs) {
+ div1 = (clk_ctrl & CLK_CTRL_DIV1_MASK) >> CLK_CTRL_DIV1_SHIFT;
+ if (!div1)
+ div1 = 1;
+ }
+#endif
+
+ pll = zynq_clk_get_peripheral_pll(clk_ctrl);
+
+ return
+ DIV_ROUND_CLOSEST(
+ DIV_ROUND_CLOSEST(
+ zynq_clk_get_pll_rate(priv, pll), div0),
+ div1);
+}
+
+#ifndef CONFIG_SPL_BUILD
+static ulong zynq_clk_get_gem_rate(struct zynq_clk_priv *priv, enum zynq_clk id)
+{
+ struct clk *parent;
+
+ if (zynq_clk_get_gem_rclk(id) == mio_clk)
+ return zynq_clk_get_peripheral_rate(priv, id, true);
+
+ parent = &priv->gem_emio_clk[id - gem0_clk];
+ if (parent->dev)
+ return clk_get_rate(parent);
+
+ debug("%s: gem%d emio rx clock source unknown\n", __func__,
+ id - gem0_clk);
+
+ return -ENOSYS;
+}
+
+static unsigned long zynq_clk_calc_peripheral_two_divs(ulong rate,
+ ulong pll_rate,
+ u32 *div0, u32 *div1)
+{
+ long new_err, best_err = (long)(~0UL >> 1);
+ ulong new_rate, best_rate = 0;
+ u32 d0, d1;
+
+ for (d0 = 1; d0 <= ZYNQ_CLK_MAXDIV; d0++) {
+ for (d1 = 1; d1 <= ZYNQ_CLK_MAXDIV >> 1; d1++) {
+ new_rate = DIV_ROUND_CLOSEST(
+ DIV_ROUND_CLOSEST(pll_rate, d0), d1);
+ new_err = abs(new_rate - rate);
+
+ if (new_err < best_err) {
+ *div0 = d0;
+ *div1 = d1;
+ best_err = new_err;
+ best_rate = new_rate;
+ }
+ }
+ }
+
+ return best_rate;
+}
+
+static ulong zynq_clk_set_peripheral_rate(struct zynq_clk_priv *priv,
+ enum zynq_clk id, ulong rate,
+ bool two_divs)
+{
+ enum zynq_clk pll;
+ u32 clk_ctrl, div0 = 0, div1 = 0;
+ ulong pll_rate, new_rate;
+ u32 *reg;
+
+ reg = zynq_clk_get_register(id);
+ clk_ctrl = readl(reg);
+
+ pll = zynq_clk_get_peripheral_pll(clk_ctrl);
+ pll_rate = zynq_clk_get_pll_rate(priv, pll);
+ clk_ctrl &= ~CLK_CTRL_DIV0_MASK;
+ if (two_divs) {
+ clk_ctrl &= ~CLK_CTRL_DIV1_MASK;
+ new_rate = zynq_clk_calc_peripheral_two_divs(rate, pll_rate,
+ &div0, &div1);
+ clk_ctrl |= div1 << CLK_CTRL_DIV1_SHIFT;
+ } else {
+ div0 = DIV_ROUND_CLOSEST(pll_rate, rate);
+ if (div0 > ZYNQ_CLK_MAXDIV)
+ div0 = ZYNQ_CLK_MAXDIV;
+ new_rate = DIV_ROUND_CLOSEST(rate, div0);
+ }
+ clk_ctrl |= div0 << CLK_CTRL_DIV0_SHIFT;
+
+ zynq_slcr_unlock();
+ writel(clk_ctrl, reg);
+ zynq_slcr_lock();
+
+ return new_rate;
+}
+
+static ulong zynq_clk_set_gem_rate(struct zynq_clk_priv *priv, enum zynq_clk id,
+ ulong rate)
+{
+ struct clk *parent;
+
+ if (zynq_clk_get_gem_rclk(id) == mio_clk)
+ return zynq_clk_set_peripheral_rate(priv, id, rate, true);
+
+ parent = &priv->gem_emio_clk[id - gem0_clk];
+ if (parent->dev)
+ return clk_set_rate(parent, rate);
+
+ debug("%s: gem%d emio rx clock source unknown\n", __func__,
+ id - gem0_clk);
+
+ return -ENOSYS;
+}
+#endif
+
+#ifndef CONFIG_SPL_BUILD
+static ulong zynq_clk_get_rate(struct clk *clk)
+{
+ struct zynq_clk_priv *priv = dev_get_priv(clk->dev);
+ enum zynq_clk id = clk->id;
+ bool two_divs = false;
+
+ switch (id) {
+ case armpll_clk ... iopll_clk:
+ return zynq_clk_get_pll_rate(priv, id);
+ case cpu_6or4x_clk ... cpu_1x_clk:
+ return zynq_clk_get_cpu_rate(priv, id);
+ case ddr2x_clk:
+ return zynq_clk_get_ddr2x_rate(priv);
+ case ddr3x_clk:
+ return zynq_clk_get_ddr3x_rate(priv);
+ case dci_clk:
+ return zynq_clk_get_dci_rate(priv);
+ case gem0_clk ... gem1_clk:
+ return zynq_clk_get_gem_rate(priv, id);
+ case fclk0_clk ... can1_clk:
+ two_divs = true;
+ /* fall through */
+ case dbg_trc_clk ... dbg_apb_clk:
+ case lqspi_clk ... pcap_clk:
+ case sdio0_clk ... spi1_clk:
+ return zynq_clk_get_peripheral_rate(priv, id, two_divs);
+ case dma_clk:
+ return zynq_clk_get_cpu_rate(priv, cpu_2x_clk);
+ case usb0_aper_clk ... smc_aper_clk:
+ return zynq_clk_get_cpu_rate(priv, cpu_1x_clk);
+ default:
+ return -ENXIO;
+ }
+}
+
+static ulong zynq_clk_set_rate(struct clk *clk, ulong rate)
+{
+ struct zynq_clk_priv *priv = dev_get_priv(clk->dev);
+ enum zynq_clk id = clk->id;
+ bool two_divs = false;
+
+ switch (id) {
+ case gem0_clk ... gem1_clk:
+ return zynq_clk_set_gem_rate(priv, id, rate);
+ case fclk0_clk ... can1_clk:
+ two_divs = true;
+ /* fall through */
+ case lqspi_clk ... pcap_clk:
+ case sdio0_clk ... spi1_clk:
+ case dbg_trc_clk ... dbg_apb_clk:
+ return zynq_clk_set_peripheral_rate(priv, id, rate, two_divs);
+ default:
+ return -ENXIO;
+ }
+}
+#else
+static ulong zynq_clk_get_rate(struct clk *clk)
+{
+ struct zynq_clk_priv *priv = dev_get_priv(clk->dev);
+ enum zynq_clk id = clk->id;
+
+ switch (id) {
+ case cpu_6or4x_clk ... cpu_1x_clk:
+ return zynq_clk_get_cpu_rate(priv, id);
+ case ddr3x_clk:
+ return zynq_clk_get_ddr3x_rate(priv);
+ case lqspi_clk ... pcap_clk:
+ case sdio0_clk ... spi1_clk:
+ return zynq_clk_get_peripheral_rate(priv, id, 0);
+ default:
+ return -ENXIO;
+ }
+}
+#endif
+
+static struct clk_ops zynq_clk_ops = {
+ .get_rate = zynq_clk_get_rate,
+#ifndef CONFIG_SPL_BUILD
+ .set_rate = zynq_clk_set_rate,
+#endif
+};
+
+static int zynq_clk_probe(struct udevice *dev)
+{
+ struct zynq_clk_priv *priv = dev_get_priv(dev);
+#ifndef CONFIG_SPL_BUILD
+ unsigned int i;
+ char name[16];
+ int ret;
+
+ for (i = 0; i < 2; i++) {
+ sprintf(name, "gem%d_emio_clk", i);
+ ret = clk_get_by_name(dev, name, &priv->gem_emio_clk[i]);
+ if (ret < 0 && ret != -FDT_ERR_NOTFOUND) {
+ dev_err(dev, "failed to get %s clock\n", name);
+ return ret;
+ }
+ }
+#endif
+
+ priv->ps_clk_freq = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+ "ps-clk-frequency", 33333333UL);
+
+ return 0;
+}
+
+static const struct udevice_id zynq_clk_ids[] = {
+ { .compatible = "xlnx,ps7-clkc"},
+ {}
+};
+
+U_BOOT_DRIVER(zynq_clk) = {
+ .name = "zynq_clk",
+ .id = UCLASS_CLK,
+ .of_match = zynq_clk_ids,
+ .flags = DM_FLAG_PRE_RELOC,
+ .ops = &zynq_clk_ops,
+ .priv_auto_alloc_size = sizeof(struct zynq_clk_priv),
+ .probe = zynq_clk_probe,
+};
* SPDX-License-Identifier: GPL-2.0+
*/
+#include <clk.h>
#include <common.h>
#include <dm.h>
#include <fdtdec.h>
#include <malloc.h>
#include <sdhci.h>
+DECLARE_GLOBAL_DATA_PTR;
+
#ifndef CONFIG_ZYNQ_SDHCI_MIN_FREQ
# define CONFIG_ZYNQ_SDHCI_MIN_FREQ 0
#endif
struct arasan_sdhci_plat {
struct mmc_config cfg;
struct mmc mmc;
+ unsigned int f_max;
};
static int arasan_sdhci_probe(struct udevice *dev)
struct arasan_sdhci_plat *plat = dev_get_platdata(dev);
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
struct sdhci_host *host = dev_get_priv(dev);
+ struct clk clk;
+ unsigned long clock;
int ret;
+ ret = clk_get_by_index(dev, 0, &clk);
+ if (ret < 0) {
+ dev_err(dev, "failed to get clock\n");
+ return ret;
+ }
+
+ clock = clk_get_rate(&clk);
+ if (IS_ERR_VALUE(clock)) {
+ dev_err(dev, "failed to get rate\n");
+ return clock;
+ }
+ debug("%s: CLK %ld\n", __func__, clock);
+
+ ret = clk_enable(&clk);
+ if (ret && ret != -ENOSYS) {
+ dev_err(dev, "failed to enable clock\n");
+ return ret;
+ }
+
host->quirks = SDHCI_QUIRK_WAIT_SEND_CMD |
SDHCI_QUIRK_BROKEN_R1B;
host->quirks |= SDHCI_QUIRK_NO_HISPD_BIT;
#endif
- host->max_clk = CONFIG_ZYNQ_SDHCI_MAX_FREQ;
+ host->max_clk = clock;
- ret = sdhci_setup_cfg(&plat->cfg, host, 0,
+ ret = sdhci_setup_cfg(&plat->cfg, host, plat->f_max,
CONFIG_ZYNQ_SDHCI_MIN_FREQ);
host->mmc = &plat->mmc;
if (ret)
static int arasan_sdhci_ofdata_to_platdata(struct udevice *dev)
{
+ struct arasan_sdhci_plat *plat = dev_get_platdata(dev);
struct sdhci_host *host = dev_get_priv(dev);
host->name = dev->name;
host->ioaddr = (void *)dev_get_addr(dev);
+ plat->f_max = fdtdec_get_int(gd->fdt_blob, dev->of_offset,
+ "max-frequency", CONFIG_ZYNQ_SDHCI_MAX_FREQ);
+
return 0;
}
}
#endif
-/*
- * Calculates the values to be used to specify the address range
- * for the MC private DRAM block, in the MCFBALR/MCFBAHR registers.
- * It returns the highest 512MB-aligned address within the given
- * address range, in '*aligned_base_addr', and the number of 256 MiB
- * blocks in it, in 'num_256mb_blocks'.
- */
-static int calculate_mc_private_ram_params(u64 mc_private_ram_start_addr,
- size_t mc_ram_size,
- u64 *aligned_base_addr,
- u8 *num_256mb_blocks)
-{
- u64 addr;
- u16 num_blocks;
-
- if (mc_ram_size % MC_RAM_SIZE_ALIGNMENT != 0) {
- printf("fsl-mc: ERROR: invalid MC private RAM size (%lu)\n",
- mc_ram_size);
- return -EINVAL;
- }
-
- num_blocks = mc_ram_size / MC_RAM_SIZE_ALIGNMENT;
- if (num_blocks < 1 || num_blocks > 0xff) {
- printf("fsl-mc: ERROR: invalid MC private RAM size (%lu)\n",
- mc_ram_size);
- return -EINVAL;
- }
-
- addr = (mc_private_ram_start_addr + mc_ram_size - 1) &
- MC_RAM_BASE_ADDR_ALIGNMENT_MASK;
-
- if (addr < mc_private_ram_start_addr) {
- printf("fsl-mc: ERROR: bad start address %#llx\n",
- mc_private_ram_start_addr);
- return -EFAULT;
- }
-
- *aligned_base_addr = addr;
- *num_256mb_blocks = num_blocks;
- return 0;
-}
-
static int mc_fixup_dpc_mac_addr(void *blob, int noff, int dpmac_id,
struct eth_device *eth_dev)
{
size_t raw_image_size = 0;
#endif
struct mc_version mc_ver_info;
- u64 mc_ram_aligned_base_addr;
u8 mc_ram_num_256mb_blocks;
size_t mc_ram_size = mc_get_dram_block_size();
-
- error = calculate_mc_private_ram_params(mc_ram_addr,
- mc_ram_size,
- &mc_ram_aligned_base_addr,
- &mc_ram_num_256mb_blocks);
- if (error != 0)
+ mc_ram_num_256mb_blocks = mc_ram_size / MC_RAM_SIZE_ALIGNMENT;
+ if (mc_ram_num_256mb_blocks < 1 || mc_ram_num_256mb_blocks > 0xff) {
+ error = -EINVAL;
+ printf("fsl-mc: ERROR: invalid MC private RAM size (%lu)\n",
+ mc_ram_size);
goto out;
+ }
/*
* Management Complex cores should be held at reset out of POR.
/*
* Tell MC what is the address range of the DRAM block assigned to it:
*/
- reg_mcfbalr = (u32)mc_ram_aligned_base_addr |
+ reg_mcfbalr = (u32)mc_ram_addr |
(mc_ram_num_256mb_blocks - 1);
out_le32(&mc_ccsr_regs->reg_mcfbalr, reg_mcfbalr);
out_le32(&mc_ccsr_regs->reg_mcfbahr,
- (u32)(mc_ram_aligned_base_addr >> 32));
+ (u32)(mc_ram_addr >> 32));
out_le32(&mc_ccsr_regs->reg_mcfapr, FSL_BYPASS_AMQ);
/*
*/
u64 mc_get_dram_addr(void)
{
- u64 mc_ram_addr;
-
- /*
- * The MC private DRAM block was already carved at the end of DRAM
- * by board_init_f() using CONFIG_SYS_MEM_TOP_HIDE:
- */
- if (gd->bd->bi_dram[1].start) {
- mc_ram_addr =
- gd->bd->bi_dram[1].start + gd->bd->bi_dram[1].size;
- } else {
- mc_ram_addr =
- gd->bd->bi_dram[0].start + gd->bd->bi_dram[0].size;
- }
-
- return mc_ram_addr;
+ return gd->arch.resv_ram;
}
/**
u32 rxbd_current;
u32 rx_first_buf;
int phyaddr;
- u32 emio;
int init;
struct zynq_gem_regs *iobase;
phy_interface_t interface;
struct phy_device *phydev;
int phy_of_handle;
struct mii_dev *bus;
-#ifdef CONFIG_CLK_ZYNQMP
struct clk clk;
-#endif
};
static u32 phy_setup_op(struct zynq_gem_priv *priv, u32 phy_addr, u32 regnum,
break;
}
- /* Change the rclk and clk only not using EMIO interface */
- if (!priv->emio)
-#ifndef CONFIG_CLK_ZYNQMP
- zynq_slcr_gem_clk_setup((ulong)priv->iobase !=
- ZYNQ_GEM_BASEADDR0, clk_rate);
-#else
- ret = clk_set_rate(&priv->clk, clk_rate);
- if (IS_ERR_VALUE(ret))
- return -1;
-#endif
+ ret = clk_set_rate(&priv->clk, clk_rate);
+ if (IS_ERR_VALUE(ret) && ret != (unsigned long)-ENOSYS) {
+ dev_err(dev, "failed to set tx clock rate\n");
+ return ret;
+ }
+
+ ret = clk_enable(&priv->clk);
+ if (ret && ret != -ENOSYS) {
+ dev_err(dev, "failed to enable tx clock\n");
+ return ret;
+ }
setbits_le32(®s->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
ZYNQ_GEM_NWCTRL_TXEN_MASK);
priv->tx_bd = (struct emac_bd *)bd_space;
priv->rx_bd = (struct emac_bd *)((ulong)bd_space + BD_SEPRN_SPACE);
-#ifdef CONFIG_CLK_ZYNQMP
ret = clk_get_by_name(dev, "tx_clk", &priv->clk);
if (ret < 0) {
dev_err(dev, "failed to get clock\n");
return -EINVAL;
}
-#endif
priv->bus = mdio_alloc();
priv->bus->read = zynq_gem_miiphy_read;
pdata->iobase = (phys_addr_t)dev_get_addr(dev);
priv->iobase = (struct zynq_gem_regs *)pdata->iobase;
/* Hardcode for now */
- priv->emio = 0;
priv->phyaddr = -1;
priv->phy_of_handle = fdtdec_lookup_phandle(gd->fdt_blob, node,
}
priv->interface = pdata->phy_interface;
- priv->emio = fdtdec_get_bool(gd->fdt_blob, node, "xlnx,emio");
-
printf("ZYNQ GEM: %lx, phyaddr %x, interface %s\n", (ulong)priv->iobase,
priv->phyaddr, phy_string_for_interface(priv->interface));
the GPIO definitions and pin control functions for each available multiplex
function.
+config PINCTRL_STM32
+ bool "ST STM32 pin control driver"
+ depends on DM
+ help
+ Supports pin multiplexing control on stm32 SoCs. The driver is
+ controlled by a device tree node which contains both the GPIO
+ definitions and pin control functions for each available multiplex
+ function.
+
endif
source "drivers/pinctrl/meson/Kconfig"
obj-$(CONFIG_PINCTRL_MESON) += meson/
obj-$(CONFIG_PINCTRL_MVEBU) += mvebu/
obj-$(CONFIG_PINCTRL_STI) += pinctrl-sti.o
+obj-$(CONFIG_PINCTRL_STM32) += pinctrl_stm32.o
--- /dev/null
+#include <common.h>
+#include <asm/arch/gpio.h>
+#include <dm.h>
+#include <dm/pinctrl.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static int prep_gpio_dsc(struct stm32_gpio_dsc *gpio_dsc, u32 port_pin)
+{
+ gpio_dsc->port = (port_pin & 0xF000) >> 12;
+ gpio_dsc->pin = (port_pin & 0x0F00) >> 8;
+ debug("%s: GPIO:port= %d, pin= %d\n", __func__, gpio_dsc->port,
+ gpio_dsc->pin);
+
+ return 0;
+}
+
+static int prep_gpio_ctl(struct stm32_gpio_ctl *gpio_ctl, u32 gpio_fn, int node)
+{
+ gpio_fn &= 0x00FF;
+
+ switch (gpio_fn) {
+ case 0:
+ gpio_ctl->mode = STM32_GPIO_MODE_IN;
+ break;
+ case 1 ... 16:
+ gpio_ctl->mode = STM32_GPIO_MODE_AF;
+ gpio_ctl->af = gpio_fn - 1;
+ break;
+ case 17:
+ gpio_ctl->mode = STM32_GPIO_MODE_AN;
+ break;
+ default:
+ gpio_ctl->mode = STM32_GPIO_MODE_OUT;
+ break;
+ }
+
+ gpio_ctl->speed = fdtdec_get_int(gd->fdt_blob, node, "slew-rate", 0);
+
+ if (fdtdec_get_bool(gd->fdt_blob, node, "drive-open-drain"))
+ gpio_ctl->otype = STM32_GPIO_OTYPE_OD;
+ else
+ gpio_ctl->otype = STM32_GPIO_OTYPE_PP;
+
+ if (fdtdec_get_bool(gd->fdt_blob, node, "bias-pull-up"))
+ gpio_ctl->pupd = STM32_GPIO_PUPD_UP;
+ else if (fdtdec_get_bool(gd->fdt_blob, node, "bias-pull-down"))
+ gpio_ctl->pupd = STM32_GPIO_PUPD_DOWN;
+ else
+ gpio_ctl->pupd = STM32_GPIO_PUPD_NO;
+
+ debug("%s: gpio fn= %d, slew-rate= %x, op type= %x, pull-upd is = %x\n",
+ __func__, gpio_fn, gpio_ctl->speed, gpio_ctl->otype,
+ gpio_ctl->pupd);
+
+ return 0;
+}
+
+static int stm32_pinctrl_set_state_simple(struct udevice *dev,
+ struct udevice *periph)
+{
+ u32 pin_mux[50];
+ struct fdtdec_phandle_args args;
+ int rv, len;
+
+ /* Get node pinctrl-0 */
+ rv = fdtdec_parse_phandle_with_args(gd->fdt_blob, periph->of_offset,
+ "pinctrl-0", 0, 0, 0, &args);
+ if (rv)
+ return rv;
+ /*
+ * check for "pinmux" property in each subnode (e.g. pins1 and pins2 for
+ * usart1) of pin controller phandle "pinctrl-0"
+ * */
+ fdt_for_each_subnode(args.node, gd->fdt_blob, args.node) {
+ struct stm32_gpio_dsc gpio_dsc;
+ struct stm32_gpio_ctl gpio_ctl;
+ int i;
+
+ len = fdtdec_get_int_array_count(gd->fdt_blob, args.node,
+ "pinmux", pin_mux,
+ ARRAY_SIZE(pin_mux));
+ debug("%s: periph->name = %s, no of pinmux entries= %d\n",
+ __func__, periph->name, len);
+ if (len < 0)
+ return -EINVAL;
+ for (i = 0; i < len; i++) {
+ debug("%s: pinmux = %x\n", __func__, *(pin_mux + i));
+ prep_gpio_dsc(&gpio_dsc, *(pin_mux + i));
+ prep_gpio_ctl(&gpio_ctl, *(pin_mux + i), args.node);
+
+ rv = stm32_gpio_config(&gpio_dsc, &gpio_ctl);
+ debug("%s: rv = %d\n\n", __func__, rv);
+ if (rv)
+ return rv;
+ }
+ }
+
+ return 0;
+}
+
+static struct pinctrl_ops stm32_pinctrl_ops = {
+ .set_state_simple = stm32_pinctrl_set_state_simple,
+};
+
+static const struct udevice_id stm32_pinctrl_ids[] = {
+ { .compatible = "st,stm32f746-pinctrl" },
+ { }
+};
+
+U_BOOT_DRIVER(pinctrl_stm32) = {
+ .name = "pinctrl_stm32",
+ .id = UCLASS_PINCTRL,
+ .of_match = stm32_pinctrl_ids,
+ .ops = &stm32_pinctrl_ops,
+ .bind = dm_scan_fdt_dev,
+};
*/
#include <common.h>
+#include <clk.h>
#include <dm.h>
#include <asm/io.h>
#include <serial.h>
{
struct stm32x7_serial_platdata *plat = dev->platdata;
struct stm32_usart *const usart = plat->base;
+
+#ifdef CONFIG_CLK
+ int ret;
+ struct clk clk;
+
+ ret = clk_get_by_index(dev, 0, &clk);
+ if (ret < 0)
+ return ret;
+
+ ret = clk_enable(&clk);
+ if (ret) {
+ dev_err(dev, "failed to enable clock\n");
+ return ret;
+ }
+#endif
+
setbits_le32(&usart->cr1, USART_CR1_RE | USART_CR1_TE | USART_CR1_UE);
return 0;
}
+#if CONFIG_IS_ENABLED(OF_CONTROL)
+static const struct udevice_id stm32_serial_id[] = {
+ {.compatible = "st,stm32-usart"},
+ {.compatible = "st,stm32-uart"},
+ {}
+};
+
+static int stm32_serial_ofdata_to_platdata(struct udevice *dev)
+{
+ struct stm32x7_serial_platdata *plat = dev_get_platdata(dev);
+ fdt_addr_t addr;
+
+ addr = dev_get_addr(dev);
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ plat->base = (struct stm32_usart *)addr;
+
+ return 0;
+}
+#endif
+
static const struct dm_serial_ops stm32_serial_ops = {
.putc = stm32_serial_putc,
.pending = stm32_serial_pending,
U_BOOT_DRIVER(serial_stm32) = {
.name = "serial_stm32x7",
.id = UCLASS_SERIAL,
+ .of_match = of_match_ptr(stm32_serial_id),
+ .ofdata_to_platdata = of_match_ptr(stm32_serial_ofdata_to_platdata),
+ .platdata_auto_alloc_size = sizeof(struct stm32x7_serial_platdata),
.ops = &stm32_serial_ops,
.probe = stm32_serial_probe,
.flags = DM_FLAG_PRE_RELOC,
#include <asm/io.h>
#include <linux/compiler.h>
#include <serial.h>
-#include <asm/arch/clk.h>
#include <asm/arch/hardware.h>
DECLARE_GLOBAL_DATA_PTR;
struct zynq_uart_priv *priv = dev_get_priv(dev);
unsigned long clock;
-#if defined(CONFIG_CLK) || defined(CONFIG_SPL_CLK)
int ret;
struct clk clk;
dev_err(dev, "failed to enable clock\n");
return ret;
}
-#else
- clock = get_uart_clk(0);
-#endif
+
_uart_zynq_serial_setbrg(priv->regs, clock, baudrate);
return 0;
#define CONFIG_USB_ETHER_MCS7830
#define CONFIG_USB_ETHER_SMSC95XX
-/* Libraries */
-#define CONFIG_MD5
-
/* Extra Commands */
#define CONFIG_CMD_ENV
-#define CONFIG_CMD_MD5SUM
/* Enable that for switching of boot partitions */
/* Disabled by default as some sub-commands can brick eMMC */
/*#define CONFIG_SUPPORT_EMMC_BOOT */
* size increases then increase this size in case of secure boot as
* it uses raw u-boot image instead of fit image.
*/
-#define CONFIG_SYS_MONITOR_LEN (0x80000 + CONFIG_U_BOOT_HDR_SIZE)
+#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
#else
-#define CONFIG_SYS_MONITOR_LEN 0x80000
+#define CONFIG_SYS_MONITOR_LEN 0x100000
#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
#endif
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_SYS_SPD_BUS_NUM 0
+#ifndef CONFIG_SPL
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+#endif
#define CONFIG_DDR_ECC
#ifdef CONFIG_DDR_ECC
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_FSL_DDR_BIST
+#ifndef CONFIG_SPL
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+#endif
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_SYS_SPD_BUS_NUM 0
+#ifndef CONFIG_SPL
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+#endif
#define CONFIG_DDR_ECC
#ifdef CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */
+#ifndef CONFIG_SPL
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+#endif
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000
/* MC firmware */
-#define CONFIG_FSL_MC_ENET
/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
*/
#ifdef CONFIG_FSL_MC_ENET
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024)
-#define CONFIG_SYS_MC_RSV_MEM_ALIGN (512UL * 1024 * 1024)
#endif
/* Command line configuration */
#define CONFIG_CMD_CBFS
#define CONFIG_CMD_CRAMFS
#define CONFIG_HOST_MAX_DEVICES 4
-#define CONFIG_CMD_MD5SUM
/*
* Size of malloc() pool, before and after relocation
#define CONFIG_CMD_DFL
#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_MD5SUM
-#define CONFIG_MD5
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTARGS "console=ttySC2,115200 root=/dev/nfs ip=dhcp"
#define CONFIG_CMD_DFL
#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_MD5SUM
-#define CONFIG_MD5
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTARGS "console=ttySC2,115200 root=/dev/nfs ip=dhcp"
#define CONFIG_SYS_TEXT_BASE 0x8ef80000
#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_MD5SUM
-#define CONFIG_MD5
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTARGS "console=ttySC2,115200 root=/dev/nfs ip=dhcp"
#define CONFIG_SYS_HZ_CLOCK 1000000000 /* 1 GHz */
-/* Libraries */
-#define CONFIG_MD5
-
#define CONFIG_BOOTARGS \
"console=ttyS0,115200 earlyprintk consoleblank=0 ignore_loglevel"
#ifndef __CONFIG_TOPIC_MIAMI_H
#define __CONFIG_TOPIC_MIAMI_H
-#define CONFIG_ZYNQ_PS_CLK_FREQ 33333333UL
-
#define CONFIG_ZYNQ_I2C0
#define CONFIG_ZYNQ_I2C1
#define CONFIG_DISPLAY
#define CONFIG_I2C_EDID
-/* Define ZYBO PS Clock Frequency to 50MHz */
-#define CONFIG_ZYNQ_PS_CLK_FREQ 50000000UL
-
#include <configs/zynq-common.h>
#endif /* __CONFIG_ZYNQ_ZYBO_H */
# endif
# else
# define CONFIG_CRC32 /* FIT images need CRC32 support */
-# define CONFIG_MD5 /* and MD5 */
# define CONFIG_SHA1 /* and SHA1 */
# define CONFIG_SHA256 /* and SHA256 */
# define IMAGE_ENABLE_CRC32 1
SHA1/SHA256 progressive hashing.
Data can be streamed in a block at a time and the hashing
is performed in hardware.
+
+config MD5
+ bool
+
endmenu
menu "Compression Support"
return EFI_SUCCESS;
}
-int efi_memory_init(void)
+__weak void efi_add_known_memory(void)
{
- unsigned long runtime_start, runtime_end, runtime_pages;
- unsigned long uboot_start, uboot_pages;
- unsigned long uboot_stack_size = 16 * 1024 * 1024;
int i;
/* Add RAM */
efi_add_memory_map(start, pages, EFI_CONVENTIONAL_MEMORY,
false);
}
+}
+
+int efi_memory_init(void)
+{
+ unsigned long runtime_start, runtime_end, runtime_pages;
+ unsigned long uboot_start, uboot_pages;
+ unsigned long uboot_stack_size = 16 * 1024 * 1024;
+
+ efi_add_known_memory();
/* Add U-Boot */
uboot_start = (gd->start_addr_sp - uboot_stack_size) & ~EFI_PAGE_MASK;
CONFIG_CMD_LOADY
CONFIG_CMD_LZMADEC
CONFIG_CMD_MAX6957
-CONFIG_CMD_MD5SUM
CONFIG_CMD_MEM
CONFIG_CMD_MFSL
CONFIG_CMD_MMC_SPI
CONFIG_FSL_LBC
CONFIG_FSL_LINFLEXUART
CONFIG_FSL_MC9SDZ60
-CONFIG_FSL_MC_ENET
CONFIG_FSL_MEMAC
CONFIG_FSL_NFC_CHIPS
CONFIG_FSL_NFC_SPARE_SIZE
CONFIG_MCFTMR
CONFIG_MCFUART
CONFIG_MCLK_DIS
-CONFIG_MD5
-CONFIG_MD5SUM_VERIFY
CONFIG_MDIO_TIMEOUT
CONFIG_MECP5123
CONFIG_MEMSIZE
CONFIG_SYS_MCLINK_MAX
CONFIG_SYS_MCMEM0_VAL
CONFIG_SYS_MCMEM1_VAL
-CONFIG_SYS_MC_RSV_MEM_ALIGN
CONFIG_SYS_MDC1_PIN
CONFIG_SYS_MDCNFG_VAL
CONFIG_SYS_MDC_PIN
CONFIG_ZYNQ_HISPD_BROKEN
CONFIG_ZYNQ_I2C0
CONFIG_ZYNQ_I2C1
-CONFIG_ZYNQ_PS_CLK_FREQ
CONFIG_ZYNQ_SDHCI0
CONFIG_ZYNQ_SDHCI1
CONFIG_ZYNQ_SDHCI_MAX_FREQ
projects / u-boot / commitdiff