The Wobo i5 top set box is a somewhat curious A10s based top set box,
it uses an AXP209 rather then the AXP152 usually used in combination
with the A10s. It has an ethernet phy connected to PORTD rather then
PORTA, and its built-in usb wifi is connected via the otg controller.
The dts file changes are identical to the changes submitted to the
upstream kernel.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sat, 5 Sep 2015 15:01:31 +0000 (17:01 +0200)]
sun5i: Add q8_a13_tablet defconfig and dts
This commits adds a generic support for q8 formfactor a13 based tablets.
These tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.
The wifi is USB based, and thus not listed in devicetree.
ATM the kernel does not support the touchscreen / accelerometer on these
devices. In the future we may need multiple configs with different
CONFIG_DEFAULT_DEVICE_TREE settings, this depends on how we solve the
hw differences on the kernel side.
For now this will suffice.
The dts files are identical to the dts files submitted to the upstream
kernel for these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 5 Sep 2015 08:50:56 +0000 (10:50 +0200)]
sun4i: Add defconfig and dts for the pov protab2-ips9 tablet
The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd
screen, microsd slot, headphones, mini hdmi, mini usb b and power barrel
connectors.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Stephen Warren [Thu, 20 Aug 2015 23:38:05 +0000 (17:38 -0600)]
usb: ehci: remember init mode
When an EHCI device is registered in device mode, the HW isn't actually
initialized at all, and hence isn't left in a running state. Consequently,
when the device is deregistered, ehci_shutdown() will fail, since the HW
bits it expects to see set in response to its shutdown requests will not
be sent, and the message "EHCI failed to shut down host controller." will
be printed.
Fix ehci-hcd.c to remember whether the device was registered in host or
device mode, and only call ehci_shutdown() for host mode registrations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Lukasz Majewski [Sun, 23 Aug 2015 22:21:44 +0000 (00:21 +0200)]
tftp: update: Allow some parts of the code to be reused when CONFIG_SYS_NO_FLASH is set
Up till now it was impossible to use code from update.c when system
was not equipped with raw FLASH memory.
Such behavior prevented DFU from reusing this code.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Lukasz Majewski [Sun, 23 Aug 2015 22:21:42 +0000 (00:21 +0200)]
doc: dfu: tftp: README entry for TFTP extension of DFU
Documentation file for DFU extension. With this functionality it is now
possible to transfer FIT images with firmware updates via TFTP and use
DFU backend for storing them.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit <8bfc288c3955> ("usb: gadget: ether: Perform board
initialization from ethernet gadget driver") added board_usb_init
and board_usb_cleanup in ethernet gadget driver. But h2200 board
didn't have board_usb_init and board_usb_cleanup implementations.
This introduced the following build errors
+drivers/usb/gadget/built-in.o: In function `usb_eth_halt':
+drivers/usb/gadget/ether.c:2498: undefined reference to `board_usb_cleanup'
+drivers/usb/gadget/built-in.o: In function `usb_eth_init':
+drivers/usb/gadget/ether.c:2316: undefined reference to `board_usb_init'
Fix it here by adding empty board_usb_init and board_usb_cleanup
functions in h2200.c.
dfu: Delete superfluous initialization of the dfu_buf_size static variable
After extension of the dfu_get_buf() to also setup (implicitly) the dfu_buf_size
variable it is not needed to set dfu_buf_size to CONFIG_SYS_DFU_DATA_BUF_SIZE.
This variable is set in the dfu_get_buf() by not only considering
CONFIG_SYS_DFU_DATA_BUF but more importantly the "dfu_bufsiz" env variable.
Therefore, dfu_get_buf() should be used for initialization.
Lukasz Majewski [Sat, 15 Aug 2015 09:23:45 +0000 (11:23 +0200)]
dfu:tests: Modify dfu_gadget_test.sh to accept USB device vendor:product ID
dfu-util allows filtering on USB device vendor:product ID by using
the -d flag (-d 0451:d022).
Such option is very handy when many DFU devices are connected to a single
host PC. This commit allows testing when above situation emerges.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Lukasz Majewski <l.majewski@majess.pl>
Test HW - AM335x Beagle Bone Black
NOTE: Max size of file to transfer: 2MiB
usb: gadget: f_thor: Allocate request up to THOR_PACKET_SIZE
Allocate request up to THOR_PACKET_SIZE not the ep0->maxpacket
as the descriptors data depend on the number of descriptors
and this 64 bytes were not enough and the buffer might overflow
which results in memalign failures later.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont perform reset at the end of thor download
if configured to do reset off.
Reset may not be required in all cases and hence
provided an option to do so.
The case would be to download the images to DDR instead
of flash device.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Marek Vasut [Sun, 2 Aug 2015 23:37:28 +0000 (01:37 +0200)]
arm: socfpga: Add support for DENX MCV SoM and MCVEVK board
Add support for DENX MCV SoM, which is CycloneV based and the
associated DENX MCVEVK baseboard. The board can boot from eMMC.
Ethernet and USB is supported.
Marek Vasut [Sat, 29 Aug 2015 08:16:20 +0000 (10:16 +0200)]
arm: socfpga: Do not call board_init_r() from board_init_f()
Instead of calling board_init_r() directly from board_init_f(), just
return from board_init_f(). This will make the code continue executing
in crt0.S _main(), from which the board_init_r() is called. This patch
aligns the SoCFPGA SPL with the correct SPL design as well as reduces
the stack utilisation slightly.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Mon, 24 Aug 2015 09:51:46 +0000 (11:51 +0200)]
arm: socfpga: Assure ISWGRP 0 and 1 are inited
This fix makes sure that the ISWGRP0 and ISWGRP1 registers are
correctly inited. In case those registers are not initialized,
it is not possible to access the registers synthesised in the
FPGA through the bridges. Any such access produces data abort.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Marek Vasut [Sat, 25 Jul 2015 08:48:14 +0000 (10:48 +0200)]
mmc: dw_mmc: Probe the MMC from OF
Rework the driver to probe the MMC controller from Device Tree
and make it mandatory. There is no longer support for probing
from the ancient qts-generated header files.
This patch now also removes previous temporary workaround.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Tom Rini <trini@konsulko.com>
Sjoerd Simons [Sun, 30 Aug 2015 22:55:50 +0000 (16:55 -0600)]
rockchip: Drop first 32kb of zeros from the rkSD image type
Instead of creating a rockchip SPL SD card image with 32KB of zeros
which can be written to the start of an SD card, create the images with
only the useful data that should be written to an offset of 32KB on the
SD card.
The first 32 kilobytes aren't needed for bootup and only serve as
convenient way of accidentally obliterating your partition table.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Sun, 30 Aug 2015 22:55:49 +0000 (16:55 -0600)]
arm: Turn of d-cache before i-cache
Booting the kernel fails on RK3288 (and probably other rockchip SoCs)
when the i-cache is disabled/flushed before d-cache.
I have not investigated whether this is due to U-Boot hanging or whether
it's very early in the linux boot, but following the approach of the
various rockchip U-Boot forks (first disable d-cache then i-cache) makes
things work.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Sun, 30 Aug 2015 22:55:48 +0000 (16:55 -0600)]
rockchip: Add config_distro_bootcmd support
Now that MMC works in U-Boot add config distro command support to start
Linux in a standard fashion. One oddity here is that linux fails to load
when the fdt is relocated to above 512MB, so set fdt_high to make sure it's
loaded below that.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Sun, 30 Aug 2015 22:55:47 +0000 (16:55 -0600)]
rockchip: Turn off CONFIG_SPL_LED for firefly
With LED support enabled the SPL easily goes over the size limit (e.g.
with both Debians gcc 4.9 and 5.2 cross-compilers). Turn off LED support
in the SPL to reduce the size just enough for those compilers.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tweaked commit subject to remove _SUPPORT Signed-off-by: Simon Glass <sjg@chromium.org>
Sjoerd Simons [Sun, 30 Aug 2015 22:55:44 +0000 (16:55 -0600)]
doc: Fix reference to Rock pro when Rock 2 is meant
The Radxa Rock pro board is rk3188 based and thus won't work with U-Boot
built for RK3288. Change the documentation to refer to the intended
board, the Radxa Rock 2, which is an RK3288-based design very similar to
the firefly
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 30 Aug 2015 22:55:41 +0000 (16:55 -0600)]
rockchip: Add basic support for firefly-rk3288
The Firefly RK3288 is a suitable target board for initial mainline Rockchip
support. It includes a good set of peripherals, a recent SoC and it is
readily available.
This adds only some basic files required to allow the baord to display a
serial message in SPL and hang.
Simon Glass [Sun, 30 Aug 2015 22:55:36 +0000 (16:55 -0600)]
rockchip: rk3288: Add SDRAM init
Add code to set up the SDRAM in SPL, ready for loading U-Boot. This uses
device tree for configuration so should be able to support other RAM
configurations. It may be possible to generalise the code to support other
SoCs at some point.
Simon Glass [Sun, 30 Aug 2015 22:55:29 +0000 (16:55 -0600)]
power: Add support for ACT8846 PMIC
Add a driver for the ACT8846 PMIC. This supports several LDOs and BUCKs and
is connected to the I2C bus. This driver supports using a regulator driver
to access the regulators.
Simon Glass [Sun, 30 Aug 2015 22:55:28 +0000 (16:55 -0600)]
rockchip: Add basic peripheral and clock definitions
Add header files for the peripherals and clocks supported on Rockchip
platforms. The particular implementation (and register set) for each is
SoC-specific, but it seems that the naming can be generic.
Simon Glass [Sun, 30 Aug 2015 22:55:26 +0000 (16:55 -0600)]
rockchip: Add support for the SPI image
The Rockchip boot ROM requires a particular file format for booting from SPI.
It consists of a 512-byte header encoded with RC4, some padding and then up
to 32KB of executable code in 2KB blocks, separated by 2KB empty blocks.
Add support to mkimage so that an SPL image (u-boot-spl-dtb.bin) can be
converted to this format. This allows booting from SPI flash on supported
machines.
Simon Glass [Sun, 30 Aug 2015 22:55:25 +0000 (16:55 -0600)]
rockchip: Add support for the SD image
The Rockchip boot ROM requires a particular file format. It consists of
64KB of zeroes, a 512-byte header encoded with RC4, and then some executable
code.
Add support to mkimage so that an SPL image (u-boot-spl-dtb.bin) can be
converted to this format.
Simon Glass [Sun, 30 Aug 2015 22:55:24 +0000 (16:55 -0600)]
rockchip: Add the rkimage format to mkimage
Rockchip SoCs require certain formats for code that they execute, The
simplest format is a 4-byte header at the start of a binary file. Add
support for this so that we can create images that the boot ROM understands.
Simon Glass [Sun, 30 Aug 2015 22:55:20 +0000 (16:55 -0600)]
rockchip: Bring in RK3288 device tree file includes and bindings
Bring in required device tree files from Linux. Since mainline Linux is
somewhat behind, use the files from the Chromium tree. We can re-sync once
further code is acccepted upstream.
Simon Glass [Sun, 30 Aug 2015 22:55:17 +0000 (16:55 -0600)]
dm: Provide better debugging when a device fails to bind
All devices should bind without error. But when they don't, they can cause
driver model init to fail. A real situation where this can happen is when
there is a missing uclass.
Add a debug() call to dm_scan_fdt_node to make this easier to track.
Simon Glass [Sun, 30 Aug 2015 22:55:16 +0000 (16:55 -0600)]
dm: Improve handling of a missing uclass
When a uclass definition is missing, no drivers in that uclass can operate.
This can happen if a board has a strange collection of options (e.g. the
driver is enabled but the uclass is not).
Unfortunately this is very confusing at present. Starting up driver model
results in a -ENOENT error, which is pretty generic. Quite a big of digging
is needed to get to the root cause.
To help with this, change the error to a very strange one with no other
users in U-Boot. Also add a debug message.
Simon Glass [Sun, 30 Aug 2015 22:55:15 +0000 (16:55 -0600)]
mmc: Support bypass mode with the get_mmc_clk() method
Some SoCs want to adjust the input clock to the DWMMC block as a way of
controlling the MMC bus clock. Update the get_mmc_clk() method to support
this.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Simon Glass [Sun, 30 Aug 2015 22:55:14 +0000 (16:55 -0600)]
dm: led: Tidy up SPL options for the led and led-gpio
At present SPL does not have its own option. But these features can
increase SPL code size. Adjust the Kconfig and Makefile so that
separate a SPL option can be selected.
Simon Glass [Sun, 30 Aug 2015 22:55:13 +0000 (16:55 -0600)]
pinctrl: Add the concept of peripheral IDs
My original pinctrl patch operating using a peripheral ID enum. This was
shared between pinmux and clock and provides an easy way to specify a device
that needs to be controlled, even it is does not (yet) have a driver within
driver model.
Masahiro's new simple pinctrl gets around this by providing a
set_state_simple() pinctrl method. By passing a device to that call the
peripheral ID becomes unnecessary. If the driver needs it, it can calculate
it itself and use it internally.
However this does not solve the problem for peripheral clocks. The 'pure'
solution would be to pass a driver to the clock uclass also. But this
requires that all devices should have a driver, and a struct udevide. Also
a key optimisation of the clock uclass is allowing a peripheral clock to
be set even when there is no device for that clock.
There may be a better way to achive the same goal, but for now it seems
expedient to add in peripheral ID to the pinctrl uclass. Two methods are
added - one to get the peripheral ID and one to select it. The existing
set_state_simple() is effectively the union of these.
Peng Fan [Tue, 1 Sep 2015 09:15:03 +0000 (17:15 +0800)]
imx: vf610 add get_cpu_rev
Since we need to support runtime check for different drivers, we need
to add get_cpu_rev for vf610, otherwise there will be build errors.
This patch introduces a dummy CPU id which is not read from chip
silicon. Later when we can get the real id from chip, can fix the
value of MXC_CPU_VF610 then.
Peng Fan [Wed, 26 Aug 2015 07:40:47 +0000 (15:40 +0800)]
mxc: ocotp fix hole in shadow registers
There is a hole in shadow registers address map of size 0x100
between bank 5 and bank 6 on iMX6QP, iMX6DQ, iMX6SDL, iMX6SX and iMX6UL.
Bank 5 ends at 0x6F0 and Bank 6 starts at 0x800. When reading the fuses,
we should account for this hole in address space.
Similar hole exists between bank 14 and bank 15 of size
0x80 on iMX6QP, iMX6DQ, iMX6SDL and iMX6SX.
Note: iMX6SL has only 0-7 banks and there is no hole.
Note: iMX6UL doesn't have this one.
When reading, we use register offset, so need to account for holes
to get the correct address.
When writing, we use bank/word index, there is no need to account
for holes, always use bank/word index from fuse map.
Nikita Kiryanov [Sun, 30 Aug 2015 12:36:49 +0000 (15:36 +0300)]
arm: mx6: cm-fx6: switch to usb kbd polling via int queue
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE works better than
CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP (keyboards that previously didn't
work such as Microsoft Comfort Curve 1000 now do work, and it's also faster).
Switch to CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE.
Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Nikita Kiryanov [Sun, 30 Aug 2015 12:36:47 +0000 (15:36 +0300)]
arm: mx6: cm-fx6: force host mode on usb controller
On some CM-FX6 modules U-Boot attempts to configure the usb0 controller in
device mode, which renders it unavailable:
USB0: Port not available.
and also causes usb stop to report an error
EHCI failed to shut down host controller.
This happens mostly on MX6 Dual based modules, and is caused by the USBPHY_CTRL
register reporting USBPHY_CTRL_OTG_ID to be 1, even when it is pulled down.
Since we do not support device mode in cm-fx6 u-boot, force all controllers to
be configured as hosts.
Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
projects / u-boot / log