Santan Kumar [Thu, 15 Jun 2017 11:37:01 +0000 (17:07 +0530)]
board:ls2080ardb: Update execution of config_board_mux
Function config_board_mux() reads env variable 'hwconfig' which is
only available after relocation for QSPI boot. Move calling
config_board_mux() to misc_init_r().
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
[YS: Revise commit message] Reviewed-by: York Sun <york.sun@nxp.com>
Smart voltage translator is removed from LS2080ARDB/LS2088ARDB
RevF boards. It is only used on LS2081ARDB. Programming GPIO
is only required for LS2081ARDB.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: Revise commit message] Reviewed-by: York Sun <york.sun@nxp.com>
York Sun [Tue, 8 Aug 2017 22:45:13 +0000 (15:45 -0700)]
driver: mmc: fsl_esdhc: Fix compiling warning
Commit 4483b7eb added variable vqmmc_dev but only uses it under
CONFIG_DM_REGULATOR. Add the same macro to variable declaration to
get rid of compiling warning.
Thomas Petazzoni [Fri, 28 Jul 2017 21:46:37 +0000 (23:46 +0200)]
common/env_embedded.c: drop support for CONFIG_SYS_USE_PPCENV
CONFIG_SYS_USE_PPCENV is no longer used anywhere. It was used to put
the environment in the special .ppcenv section, but the last
architecture using this section (SuperH) has been changed to not use
it.
Therefore, this commit drops support for CONFIG_SYS_USE_PPCENV
entirely. We only handle two cases:
- We're building the host tool tools/envcrc, in which case the
environment is place with no special section attribute (so it
depends up in .data)
- We're building U-Boot itself, in which case the environnement is
placed in the .text section.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Adam Ford [Fri, 28 Jul 2017 13:32:52 +0000 (08:32 -0500)]
Convert ARCH_OMAP2PLUS boards' CONFIG_SYS_TEXT_BASE to Kconfig
This converts the following to Kconfig:
CONFIG_SYS_TEXT_BASE
The includes, whitelist, etc. were left for now but I don't get any
build errors or warnings on the omap3_logic_defconfig or
am3517_evm_defconfig builds I tried.
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Update the configuration files to support the device tree and driver
model. The peripheral clock and pins configuration are handled by
the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
board: at91sam9260ek: Use SPI-flash-based AT45xxx DataFlash
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
board: at91sam9rlek: Use SPI-flash-based AT45xxx DataFlash
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
board: at91sam9263ek: Use SPI-flash-based AT45xxx DataFlash
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
gpt: harden set_gpt_info() against non NULL-terminated strings
Strings read from devices may sometimes fail to be
NULL-terminated. The functions in lib/string.c are subject to
failure in this case. Protect against observed failures in
set_gpt_info() by switching to length-checking variants with a length
limit of the maximum possible partition table length. At the same
time, add a few checks for NULL string pointers.
Here is an example as observed in sandbox under GDB:
=> gpt verify host 0 $partitions
Program received signal SIGSEGV, Segmentation fault.
0x0000000000477747 in strlen (s=0x0) at lib/string.c:267
267 for (sc = s; *sc != '\0'; ++sc)
(gdb) bt
#0 0x0000000000477747 in strlen (s=0x0) at lib/string.c:267
#1 0x00000000004140b2 in set_gpt_info (str_part=<optimized out>,
str_disk_guid=str_disk_guid@entry=0x7fffffffdbe8, partitions=partitions@entry=0x7fffffffdbd8,
parts_count=parts_count@entry=0x7fffffffdbcf "", dev_desc=<optimized out>) at cmd/gpt.c:415
#2 0x00000000004145b9 in gpt_verify (str_part=<optimized out>, blk_dev_desc=0x7fffef09a9d0) at cmd/gpt.c:580
#3 do_gpt (cmdtp=<optimized out>, flag=<optimized out>, argc=<optimized out>, argv=0x7fffef09a8f0)
at cmd/gpt.c:783
#4 0x00000000004295b0 in cmd_call (argv=0x7fffef09a8f0, argc=0x5, flag=<optimized out>,
cmdtp=0x714e20 <_u_boot_list_2_cmd_2_gpt>) at common/command.c:500
#5 cmd_process (flag=<optimized out>, argc=0x5, argv=0x7fffef09a8f0,
repeatable=repeatable@entry=0x726c04 <flag_repeat>, ticks=ticks@entry=0x0) at common/command.c:539
GPT: provide commands to selectively rename partitions
This patch provides support in u-boot for renaming GPT
partitions. The renaming is accomplished via new 'gpt swap'
and 'gpt rename' commands.
The 'swap' mode returns an error if no matching partition names
are found, or if the number of partitions with one name does not equal
the number with the second name. The 'rename' variant always
succeeds as long as a partition with the provided number exists.
Rewriting the partition table has the side-effect that all partitions
end up with "msftdata" flag set. The reason is that partition type
PARTITION_BASIC_DATA_GUID is hard-coded in the gpt_fill_pte()
function. This does not appear to cause any harm.
GPT: read partition table from device into a data structure
Make the partition table available for modification by reading it from
the user-specified device into a linked list. Provide an accessor
function for command-line testing.
Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
[trini: Make this depend on CMD_GPT_RENAME, as it is the user of this
code] Signed-off-by: Tom Rini <trini@konsulko.com>
Alison Chaiken [Sun, 25 Jun 2017 23:43:23 +0000 (16:43 -0700)]
GPT: add accessor function for disk GUID
In order to read the GPT, modify the partition name strings, and then
write out a new GPT, the disk GUID is needed. While there is an
existing accessor for the partition UUIDs, there is none yet for the
disk GUID.
Alison Chaiken [Sun, 25 Jun 2017 23:43:22 +0000 (16:43 -0700)]
partitions: increase MAX_SEARCH_PARTITIONS and move to part.h
Move MAX_SEARCH_PARTITIONS to part.h so that functions in cmd
directory can find it. At the same time, increase the value to
64 since some operating systems use many, and the resources
consumed by a larger value are minimal.
Alison Chaiken [Sun, 25 Jun 2017 23:43:19 +0000 (16:43 -0700)]
GPT: fix error in partitions string doc
The existing partitions-list parsing in cmd/gpt.c passes a value
from gpt_default() to set_gpt_info() that README.gpt suggests
should begin with 'partitions='. Partition-list strings should
in fact begin with 'uuid_disk', as otherwise the call from
set_gpt_info() to extract_val() to find 'uuid_disk' will fail.
Change README.gpt accordingly.
Tom Rini [Thu, 3 Aug 2017 13:33:07 +0000 (09:33 -0400)]
PowerPC: mpc85xx: Update ft_verify_fdt
With the changes to fdt_get_base_address() we need to modify the logic
in ft_verify_fdt() for how we check the validity of the CCSR address.
Tested-on: qemu-ppce500 -M mpc8544ds Fixes: 336a44877af8 ("fdt: Correct fdt_get_base_address()") Cc: York Sun <york.sun@nxp.com> Cc: Wolfgang Denk <wd@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
The logic of what fdt_get_base_address() will search for and return has
changed. Rework get_phys_ccsrbar_addr_early() to perform the logic that
fdt_get_base_address used to perform.
Fixes: 336a44877af8 ("fdt: Correct fdt_get_base_address()") Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Alexander Graf <agraf@suse.de> Signed-off-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Fri, 21 Jul 2017 21:20:34 +0000 (23:20 +0200)]
net: ravb: Detect PHY correctly
The order of parameters passed to the phy_connect() was wrong.
Moreover, only PHY address 0 was used. Replace this with code
capable of detecting the PHY address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Fri, 21 Jul 2017 21:19:18 +0000 (23:19 +0200)]
serial: sh: Use the clock framework to obtain clock config
Since we now have clock driver on the RCar Gen3 , obtain the clock
configuration using the clock framework functions. In case this
fails, fall back to the original code for pulling the clock config
directly out of OF.
Marek Vasut [Fri, 21 Jul 2017 21:18:03 +0000 (23:18 +0200)]
clk: rmobile: Add RCar Gen3 clock driver
Add clock driver for the RCar Gen3 R8A7795 and R8A7796 SoCs .
This driver allows reading out the clock configuration set by
previous boot stages and enabling and disabling clock using
the MSTP registers. Setting clock is not supported thus far.
Marek Vasut [Fri, 21 Jul 2017 21:16:59 +0000 (23:16 +0200)]
ARM: dts: rmobile: Import DTS from Linux 4.12
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.12-rc6,
commit 6f7da290413ba713f0cdd9ff1a2a9bb129ef4f6c . This includes both M3
and H3 ULCB and Salvator-X boards.
arm64: zynqmp: Make chip_id routine to handle based on el.
Modify chip_id() routine such that to handle based on
the current el. Also make it available even if FPGA is
not enabled in system such it can be used always.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 20 Jul 2017 10:38:27 +0000 (12:38 +0200)]
arm64: zynqmp: Move dts zcu102 to zcu102-revA
Not using board revision is causing confusion about which board is
supported and tested. Mark dts files exactly with board revision which
was tested. When new board revision arives it can be symlink if SW view
is the same. Also add -revX suffix to compatible string because user space
tools are parsing this string and can change behavior depends of board
revision.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Wed, 28 Jun 2017 13:40:32 +0000 (15:40 +0200)]
arm64: zynqmp: Fix SVD mask for getting chip ID
Mask should start from the first bit - using 0xe is just wrong.
3bits are used that's why 0x7 mask is correct.
This patch is fixing silicon ID code detection. Previous behavior was
that bit0 was completely ignored.
Issue was found on 2eg chip detection.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: zynqmp: Remove ifdef around zynqmp mmio read and write rotuines
This patch removes ifdef around mmio read and write rotuines
and make them a single routine by checking the current el.
This patch helps to remove ifdef around invoke_smc as well.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
fpga: xilinx: Avoid using local intermediate buffer
Dont use local temporary buffer for printing out the
info instead use directly from memroy. This fixes the
issue of stack corruprion due to local buffer overflow.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for CCF, this CCF reads the ref clocks
from dt and checks all the required clock control
registers for its source , divisors and calculates
the clock from them. This supports clock and set
functions.
Panic when read/write fails.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Alexander Graf [Mon, 3 Jul 2017 11:41:36 +0000 (13:41 +0200)]
zynq: Add Z-Turn board
The Z-Turn board is a low cost development board based on the
Xilinx Zynq SoC. While it's powerful and quite versatile, it
so far lacked upstream support.
This patch adds basic support for the Z-Turn. It does however
for now miss enablement for MIO51 reset which means that USB
and ethernet don't work. For that either FSBL or SPL need to
be adjusted. The SPL part will follow later.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Alexander Graf [Mon, 3 Jul 2017 11:41:35 +0000 (13:41 +0200)]
zynq: Enable distro boot
Distro boot allows devices to boot using standardized boot methods by
default. This can be very handy for distributions that want to run on
different platforms.
This patch moves the zynq platform to use its old, zynq specific boot
method first and then fall back to distro boot. That way supporting
Linux distributions like openSUSE is much easier.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Alexander Graf [Mon, 3 Jul 2017 11:41:34 +0000 (13:41 +0200)]
zynq: Add EFI runtime sections to linker script
When using EFI_LOADER, we add a few special sections for runtime code and
data which get relocated on demand when executing a target OS.
These runtime structures need to get annotated properly in the linker script.
While we do that properly in the generic one, we missed out on the zynq
specific linker script.
This patch adds the EFI runtime section annotations into the zynq linker script
so that the efi loader code actually works on that platform.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
VINITHA PILLAI [Mon, 12 Jun 2017 04:13:45 +0000 (09:43 +0530)]
arm64: ls2088ardb: Add distro secure boot support
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Also enable "secureboot=y"
flag in environment for ARM based platforms instead of bootcmd.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Include common config_distro_defaults.h and config_distro_bootcmd.h
for u-boot enviroments to support automatical distro boot which
scan boot.scr from external storage devices(e.g. SD/USB/SATA/SCSI disk)
and execute autoboot script. Tested on ls2088ardb with automatically
boot Ubuntu from SD card or USB disk, if it fails to detect external
storage disk, fall back to nor/qspi boot.
Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Tue, 6 Jun 2017 15:21:31 +0000 (20:51 +0530)]
arm: ls1021atwr: Add distro secure boot support
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Disable fall back option to
qspi boot in case of secure boot. Also enable "secureboot=y" flag
in environment for ARM based platforms instead of bootcmd.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Tue, 6 Jun 2017 15:20:29 +0000 (20:50 +0530)]
arm64: ls1046ardb: Add distro secure boot support
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Disable fall back option to
qspi boot in case of secure boot. Also enable "secureboot=y" flag
in environment for ARM based platforms instead of bootcmd.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Mon, 5 Jun 2017 18:21:51 +0000 (23:51 +0530)]
arm64: ls1043ardb: Add distro secure boot support
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Disable fall back option to
nor/qspi boot in case of secure boot. Also enable "secureboot=y"
flag in environment for ARM based platforms instead of bootcmd.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Shengzhou Liu [Thu, 8 Jun 2017 07:59:48 +0000 (15:59 +0800)]
arm64: ls1043ardb: Add distro boot support
Include common config_distro_defaults.h and config_distro_bootcmd.h
for u-boot enviroments to support automatical distro boot which
scan boot.scr from external storage devices(e.g. SD/USB/SATA/SCSI disk)
and execute autoboot script. Tested on ls1043ardb with automatically
boot Ubuntu from SD card or USB disk, if it fails to detect external
storage disk, fall back to nor/qspi boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Alison Wang [Fri, 26 May 2017 07:46:15 +0000 (15:46 +0800)]
arm: ls1021atwr: Add distro boot support
This patch includes common config_distro_defaults.h and
config_distro_bootcmd.h for u-boot enviroments to support distro boot
which automatically scan boot.scr from storage devices(e.g.
SD/USB/SATA/SCSI disk) and execute autoboot script on LS1021ATWR board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Simon Glass [Mon, 31 Jul 2017 02:24:01 +0000 (19:24 -0700)]
x86: Convert MMC to driver model
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove DM_MMC from edison_defconfig] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Sun, 30 Jul 2017 13:23:26 +0000 (06:23 -0700)]
x86: kconfig: Let board select SPI flash
Only a specific type of SPI flash exists on a board, having board
Kconfig to select the SPI flash seems to make more sense. Other
flash types are not necessary except coreboot, which implies all
available flash drivers there.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>