York Sun [Mon, 29 Jan 2018 17:44:33 +0000 (09:44 -0800)]
drivers/ddr/fsl: Fix DDR4 RDIMM support
For DDR4, command/address delay in mode registers and parity latency
in timing config register are only needed for UDIMMs, but not RDIMMs.
Add additional register rcw_3 for DDR4 RDIMM. Fix mirrored bit for
dual rank RDIMMs. Set sdram_cfg_3[DIS_MRS_PAR] for RDIMMs. Fix
calculation of timing config registers. Use hexadecimal format for
printing RCW (register control word) registers.
Yogesh Gaur [Tue, 16 Jan 2018 04:38:24 +0000 (10:08 +0530)]
driver: fsl-mc: Perform fsl-mc fdt fixup for lazyapply dpl
For for case of lazyapply method, API fdt_fixup_board_enet() gets
invoked before DPL being deployed. This leads to an issue that
fsl-mc fdt fixup status marked as fail and dprc driver didn't get
registered in linux boot.
Fixes this issue by calling fdt_fixup_board_enet() for case when
DPL is deployed successfully in lazyapply method.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Alexander Graf [Mon, 29 Jan 2018 12:57:20 +0000 (13:57 +0100)]
serial: Make full device search optional
Commit 608b0c4ad4e5ec0c ("serial: Use next serial device if probing fails")
added code to search for more serial devices if the default one was not
probed correctly.
Unfortunately, that breaks omap3_evm. So while investigating why that is
the case, let's disable the full search for everyone but bcm283x where it
is needed.
Fixes: 608b0c4ad4e5ec0c ("serial: Use next serial device if probing fails") Reported-by: Derald D. Woods <woods.technical@gmail.com> Signed-off-by: Alexander Graf <agraf@suse.de>
Andreas Färber [Sat, 20 Jan 2018 12:07:09 +0000 (13:07 +0100)]
tools/mrvl_uart.sh: Fix minicom baudrate
minicom doesn't inherit the baudrate from stty but uses its own
defaults, such as for example 57600, whereas we expect 115200 here.
Explicitly tell minicom which baudrate to use.
Fixes: eee4835d22 ("tools: Add Marvell recovery image download script") Cc: Konstantin Porotchkin <kostap@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Igal Liberman <igall@marvell.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
The variable cfi_flash_num_flash_banks is defined iff
CONFIG_SYS_MAX_FLASH_BANKS_DETECT is defined, but it is used
unconditionally in the function cfi_flash_init_dm. This leads to a
undefined variable compile error when CONFIG_SYS_MAX_FLASH_BANKS_DETECT
is not defined, but DM is enabled.
Fix this by always defining the cfi_flash_num_flash_banks variable.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
Mario Six [Fri, 26 Jan 2018 13:43:55 +0000 (14:43 +0100)]
cfi_flash: Fix indention
When long expressions surrounded by parentheses are split into multiple
lines, each consecutive line should be aligned with the corresponding
parenthesis. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
Mario Six [Fri, 26 Jan 2018 13:43:53 +0000 (14:43 +0100)]
cfi_flash: Bound-check index before array access
In a while loop in cfi_flash.c the array "start" is accessed at the index
"sector" before the index variable "sector" is bounds-checked, which
might lead to accesses beyond the bounds of the array.
Swap the order of the checks in the "&&" expression, so that the
short-circuit evaluation prevents out-of-bounds array accesses.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
Mario Six [Fri, 26 Jan 2018 13:43:49 +0000 (14:43 +0100)]
cfi_flash: Use u8 pointers instead of void pointers
According to the C standard, pointer arithmetic for pointers of type
void is undefined behavior (the assumption that they're 8-bit wide is a
GCC-specific assumption). In the interest of keeping the code
standards-compliant, and also better communicate intent, switch all
void* variables where pointer arithmetic is used to u8* variables.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
Mario Six [Fri, 26 Jan 2018 13:43:48 +0000 (14:43 +0100)]
cfi_flash: Remove assignments from if conditions
The condition in if statements should not be used for variable
assignment. Instead, the assignment should be done in a separate step
beforehand. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
Mario Six [Fri, 26 Jan 2018 13:43:45 +0000 (14:43 +0100)]
cfi_flash: Fix else after break
If in a loop, the if block in a if/else statement ends in a break, the
statements in the else blockcan be extracted, since the break stops the
execution.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
Mario Six [Fri, 26 Jan 2018 13:43:43 +0000 (14:43 +0100)]
cfi_flash: Add missing braces in blocks
In if/else statements, either both blocks (if and else) should have
braces or both blocks should not have braces, but mixed configurations
are discouraged. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
Mario Six [Fri, 26 Jan 2018 13:43:42 +0000 (14:43 +0100)]
cfi_flash: Remove unnecessary braces
"==" and "!=" bind tighter than the boolean operators, so parentheses
around them in compound logical statements are unnecessary. Fix all
instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
Mario Six [Fri, 26 Jan 2018 13:43:41 +0000 (14:43 +0100)]
cfi_flash: Fix comment style
Comment blocks should end with a "*/" on a separate line, not with the
"*/" attached to the end of the last line of text. Fix all instances
where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
Mario Six [Fri, 26 Jan 2018 13:43:40 +0000 (14:43 +0100)]
cfi_flash: Use __func__ macro instead of function name
printf/debug statements should not include the file name as a hardcoded
string, but instead use the __func__ macro. Fix all instances where this
occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
Mario Six [Fri, 26 Jan 2018 13:43:39 +0000 (14:43 +0100)]
cfi_flash: Fix logical continuations
When splitting long logical statements across multiple lines, the
logical operators should be at the end of the lines. Fix all instances
where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
Mario Six [Fri, 26 Jan 2018 13:43:37 +0000 (14:43 +0100)]
cfi_flash: Fix missing/superfluous lines
There should be no consecutive blank lines, and no blank lines at the
end of blocks. But there should be blank lines between variable
declarations and code. Fix all instances where either occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
vsprintf.c: correct printing of a NULL device path
When printing '%pD' with a value of NULL we want to output
'<NULL>'. But this requires copying to buf. Leave this
to string16.
A unit test is supplied which relies on EFI support in the sandbox.
The development for EFI support in the sandbox is currently in branch
u-boot-dm/efi-working. The branch lacks commit 6ea8b580f06b ("efi_loader:
correct DeviceNodeToText for media types"). Ater rebasing the aforementioned
branch on U-Boot v2018.01 and adding 256060e4257a2 and this patch the test
is executed successfully.
Fixes: 256060e4257a2 (vsprintf.c: add EFI device path printing) Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 23:47:53 +0000 (00:47 +0100)]
efi_loader: Call Exit() on return from payload in StartImage()
When a UEFI payload just returns instead of calling the Exit() callback,
we handle that in efi_do_enter() and call Exit on its behalf, so that
the loaded_image->exit_status value is correct.
We were missing that logic in StartImage(). Call it there too.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
If 'bootefi hello' or 'bootefi selftest' can be executed depends on the
configuration.
If an invalid non-numeric 1st argument is passed to bootefi, e.g.
'bootefi hola', this string is converted to 0 and U-Boot jumps to
this typically invalid address.
With the patch the online help is shown instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Tue, 23 Jan 2018 23:18:08 +0000 (00:18 +0100)]
efi_loader: Always use EFIAPI instead of asmlinkage
EFI calls are usually defined as asmlinkage. That means we pass all parameters
to functions via the stack x86_32.
On x86_64 however, we need to also stick to the MS ABI calling conventions,
which the EFIAPI define conveniently handles for us. Most EFI functions were
also marked with EFIAPI, except for the entry call.
So this patch adjusts all entry calls to use EFIAPI instead of the manual
asmlinkage attribute.
While at it, we also change the prototype of the entry point to return
efi_status_t instead of ulong, as this is the correct prototype definition.
Alexander Graf [Wed, 24 Jan 2018 13:54:21 +0000 (14:54 +0100)]
efi: Conflict efi_loader with different stub bitness
We have 2 users of the EFI headers: efi_loader and the EFI stub. Efi_loader
always expects that the bitness of the definitions it uses is identical to
the execution.
The EFI stub however allows to run x86_64 U-Boot on 32bit EFI and the other
way around, so it allows for different bitness of EFI definitions and U-Boot
environment.
This patch explicitly requests via Kconfig that efi_loader can only be enabled
if the bitness is identical. Because we can run efi_loader on x86_64 without
EFI stub enabled, it also ensures that this case propagates the correct ABI
constraints.
Alexander Graf [Thu, 25 Jan 2018 11:05:56 +0000 (12:05 +0100)]
bcm2835_pinctrl: Probe pre-reloc
The serial drivers now depend on the pinctrl driver to determine whether
they are enabled. That means if a serial device wants to be used pre-reloc,
we also need the pinctrl device pre-reloc.
Adapt the pinctrl driver as well as dts overlay accordingly.
Alexander Graf [Thu, 25 Jan 2018 11:05:55 +0000 (12:05 +0100)]
bcm2835_pl011_serial: Add BCM2835 specific serial driver
On bcm2835 we need to ensure we only access serial devices that are
muxed to the serial output pins of the pin header. To achieve this
for the pl011 device, add a bcm2835 specific pl011 wrapper device
that does this check but otherwise behaves like a pl011 device.
Alexander Graf [Thu, 25 Jan 2018 11:05:54 +0000 (12:05 +0100)]
MAINTAINERS: Take over BCM2835 maintainership
It seems as if I have more interest in BCM2835 support than most others,
so I'll bite the bullet and declare myself maintainer. It'd be a shame
to leave that platform orphaned.
Alexander Graf [Thu, 25 Jan 2018 11:05:47 +0000 (12:05 +0100)]
serial_bcm283x_mu: Always skip init
The serial initialization doesn't always quite work for me, so let's
always skip it for now. We know that firmware on the RPi initializes
us properly already.
Alexander Graf [Thu, 25 Jan 2018 11:05:45 +0000 (12:05 +0100)]
rpi: Determine PL011/Mini-UART availability at runtime
Firmware on the Raspberry Pi family of devices can dynamically configure either
the PL011, Mini-UART or no device at all to be routed to the user accessible
UART pins.
That means we need to always include both drivers, because we can never be sure
which of the two serial devices firmware actually chooses to use.
Alexander Graf [Thu, 25 Jan 2018 11:05:44 +0000 (12:05 +0100)]
serial: bcm283x_mu: Remove support for post-init disabling
We are switching to a model where a serial device doesn't even get probed when
it's not muxed properly, so we don't need device specific disabling
functionality anymore.
Alexander Graf [Thu, 25 Jan 2018 11:05:43 +0000 (12:05 +0100)]
rpi: Remove runtime disabling support for serial
We are switching to a model where our board file can directly fail probing
of serial devices when they're not usable, so remove the current runtime
hack we have.
Alexander Graf [Thu, 25 Jan 2018 11:05:42 +0000 (12:05 +0100)]
serial: Use next serial device if probing fails
Currently our serial device search chokes on the fact that the serial
probe function could fail. If it does, instead of searching for the next
usable serial device, it just quits.
This patch changes the fallback logic so that even when a serial device
was not probed correctly, we just try the next ones until we find one that
works.
Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Faiz Abbas [Wed, 24 Jan 2018 09:14:49 +0000 (14:44 +0530)]
am33xx: board: Call spl_early_init() to support sdram_init()
With driver model enabled in SPL, sdram_init() requires device tree
and malloc to be initialized.
Therefore call spl_early_init() in early_system_init().
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Alexander Graf [Tue, 23 Jan 2018 17:05:22 +0000 (18:05 +0100)]
mmc: Add bcm2835 sdhost controller
The BCM2835 family of SoCs has 2 different SD controllers: One based on
the SDHCI spec and a custom, home-grown one.
This patch implements a driver for the latter based on the Linux driver.
This is needed so that we can make use of device trees that assume driver
presence of both SD controllers.
Alexander Graf [Tue, 23 Jan 2018 17:05:21 +0000 (18:05 +0100)]
bcm283x: Add pinctrl driver
The bcm283x family of SoCs have a GPIO controller that also acts as
pinctrl controller.
This patch introduces a new pinctrl driver that can actually properly mux
devices into their device tree defined pin states and is now the primary
owner of the gpio device. The previous GPIO driver gets moved into a
subdevice of the pinctrl driver, bound to the same OF node.
That way whenever a device asks for pinctrl support, it gets it
automatically from the pinctrl driver and GPIO support is still available
in the normal command line phase.
Masahiro Yamada [Sun, 21 Jan 2018 10:19:17 +0000 (19:19 +0900)]
libfdt: migrate libfdt.h to a wrapper + U-Boot own code
There is tons of code duplication between lib/libfdt/libfdt.h and
scripts/dtc/libfdt/libfdt.h. Evacuate the U-Boot own code to
include/libfdt.h and remove lib/libfdt/libfdt.h.
For host tools, <libfdt.h> should include scripts/dtc/libfdt/libfdt.h,
which is already suitable for user-space.
For compiling U-Boot, <linux/libfdt.h> should be included because we
need a different libfdt_env.h .
I am fixing this horrible crap. In advance, I need to add necessary
include directives explicitly. tools/fdtgrep.c needs more; <fctl.h>
for open() and <errno.h> for errno.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Sun, 21 Jan 2018 10:19:13 +0000 (19:19 +0900)]
libfdt: migrate fdt_rw.c to a wrapper of scripts/dtc/libfdt/fdt_rw.c
The only difference between scripts/dtc/libfdt/fdt_rw.c and
lib/libfdt/fdt_rw.c is fdt_remove_unused_strings().
It is only used by fdtgrep, so we do not need to compile it for U-Boot
image. Move it to tools/libfdt/fdw_rw.c so that lib/libfdt/fdt_rw.c
can be a wrapper of scripts/dtc/libfdt/fdt_rw.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Derald D. Woods [Sun, 21 Jan 2018 03:16:14 +0000 (21:16 -0600)]
ARM: omap3: evm: Fix distro bootcmd UBIFS and MMC support
The omap3_evm board does not boot when commit: a47ca2cf67 ("ARM: omap3: evm: Add kernel image loading from UBIFS and EXT4")
is applied after commit: 3dde8f2037 ("Merge git://git.denx.de/u-boot-mmc")
This commit reduces the CONFIG_EXTRA_ENV_SETTINGS size and better
leverages the existing distro bootcmd infrastructure.
- Use updated UBIFS support from config_distro_bootcmd.h
- Use LEGACY_MMC naming found in am335x_evm.h and ti_omap4_common.h
- Remove extra environment content that is no longer needed
Derald D. Woods [Sun, 21 Jan 2018 03:16:13 +0000 (21:16 -0600)]
distro bootcmd: Allow board defined UBI partition and volume names
This commit allows overriding the default assumption that the boot UBI
MTD partition is named 'UBI' and the UBI volume is 'boot'. A board
desiring to use a legacy or alternative NAND layout can now define the
following two extra environment variables:
Loading files stored with lzo compression from a btrfs filesystem was
producing unaligned memory accesses, which were causing a data abort
and a reset on an Orange Pi Zero.
The change in hash.c is not triggered by any error but follows the
same pattern. Please confirm.
Fixed according to doc/README.unaligned-memory-access.txt
Signed-off-by: Alberto Sánchez Molero <alsamolero@gmail.com> Tested-by: Robert Nelson <robertcnelson@gmail.com>
Kever Yang [Wed, 17 Jan 2018 03:05:38 +0000 (11:05 +0800)]
spl: atf: pass NULL for bl32_ep pc
ATF use bl32_ep_info->pc to decide if thre is an available bl32,
let's mark it as NULL first.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Eddie Cai [Wed, 17 Jan 2018 01:51:41 +0000 (09:51 +0800)]
rockchip: rk3036: enable rockusb support on rk3036 based device
Rockchip Rockusb driver already merged. So we enable rockusb
support on rk3036 based device.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 16 Jan 2018 08:08:18 +0000 (16:08 +0800)]
rockchip: dts: rk3128: update pwm-cell for pwm0
The backlight pwm-cell is 3.
This remove the warning in buildman:
arch/arm/dts/rk3126-evb.dtb: Warning (pwms_property): Property 'pwms', cell 3 is not a phandle reference in /backlight
arch/arm/dts/rk3126-evb.dtb: Warning (pwms_property): Missing property '#pwm-cells' in node /sram@10080400 or bad phandle (referred from /backlight:pwms[3])
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Thu, 25 Jan 2018 14:27:10 +0000 (15:27 +0100)]
rockchip: clk: guard set_parent implementations against OF_PLATDATA
The set_parent implementations do not make sense when OF_PLATDATA is
enabled. We guard these against OF_PLATDATA and don't populate the
set_parent-op when this is the case.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Implement the setting parent for gmac clock, and add internal
pll div set for mac clk.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:06:33 +0000 (14:06 +0800)]
clk: rockchip: clk_rk3288: Implement "assign-clock-parent" and "assign-clock-rate"
The RK3288 CRU-node assigns rates to a number of clocks that are not
implemented in the RK3288 clock-driver (but which have been
sufficiently initialised from rkclk_init()): for these clocks, we
implement the gmac clock set parent, but simply ignore the
others' set_rate() operation and return 0 to signal success.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The LCDC assigned rate is 0, it will make boot error,
error log:"pll_para_config: the frequency can not be
0 Hz". Remove them, and the lcdc driver will do the
correct clock rate setting.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:05:51 +0000 (14:05 +0800)]
config: evb-rk3229: Enable rk gmac configs
Add gmac config support for rk3229 evb.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:05:30 +0000 (14:05 +0800)]
net: gmac_rockchip: Add support for the RK3228 GMAC
The GMAC in the RK3228 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3368-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:05:12 +0000 (14:05 +0800)]
clk: rockchip: Add rk322x gamc clock support
Assuming mac_clk is fed by an external clock, set clk_rmii_src
clock select control register from IO for rgmii interface.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:04:51 +0000 (14:04 +0800)]
rockchip: pinctrl: Add rk322x gmac pinctrl support
Set gmac pins iomux and rgmii tx pins to 12ma drive-strength,
clean others to 2ma.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:04:26 +0000 (14:04 +0800)]
rockchip: pinctrl: rk322x: Move the iomux definitions into pinctrl-driver
Clean the iomux definitions at grf_rk322x.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
After that, define the uart2 iomux at rk322x-board file.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:04:11 +0000 (14:04 +0800)]
rockchip: dts: rk3328-evb: Enable gmac2io for rk3328-evb
Add rk3328-evb gmac support.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:03:56 +0000 (14:03 +0800)]
rockchip: dts: rk3328: Add gmac2io support
Add basic dts configuration for rk3328 gmac2io.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:03:23 +0000 (14:03 +0800)]
rockchip: configs: Enable GMAC configs for evb-rk3328
Enable GMAC configs for evb-rk3328
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:03:04 +0000 (14:03 +0800)]
net: gmac_rockchip: Add rk3328 gmac support
The GMAC2IO in the RK3328 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3328-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:02:36 +0000 (14:02 +0800)]
clk: rockchip: Add rk3328 gamc clock support
The rk3328 soc has two gmac controllers, one is gmac2io,
the other is gmac2phy. We use the gmac2io rgmii interface
for 1000M phy here.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:02:07 +0000 (14:02 +0800)]
rockchip: pinctrl: Add rk3328 gmac pinctrl support
Need to set gmac m1 pins iomux, gmac m0 tx pins, select bit2
and bit10 at com iomux register. After that, set rgmii m1 tx
pins to 12ma drive-strength, and clean others to 2ma.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:01:45 +0000 (14:01 +0800)]
rockchip: pinctrl: rk3328: Move the iomux definitions into pinctrl-driver
Clean the iomux definitions at grf_rk3328.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:01:12 +0000 (14:01 +0800)]
net: gmac_rockchip: Add support for the RV1108 GMAC
The rv1108 GMAC only support rmii interface, so need to add the
set_rmii() ops. Use the phy current interface to set rmii or
rgmii ops. At the same time, need to set the mac clock rate of
rmii with 50M, the clock rate of rgmii with 125M.
Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
projects / u-boot / log